Wear your Fitbit on your inner wrist, snug but not tight, with the sensor flat against your skin
Your Fitbit tracks heart rate and movement by reading your wrist. The sensor on the back of the device needs direct contact with your skin to work. Wear it on the inside of your wrist — the soft underside, not the top — about one to two finger-widths below your wrist bone. The band should sit snug enough that it does not slide around when you move your arm, but loose enough that you can fit a finger underneath. If the band is too loose, the sensor loses contact and stops recording. If it is too tight, it cuts off circulation and becomes uncomfortable to wear all day.
The exact position matters because your Fitbit reads your pulse through the radial artery, which runs along the inside of your wrist. When the sensor sits directly over this artery with good skin contact, it gets an accurate reading. Bone, hair, and tattoos block the signal, so if you have a tattoo on your inner wrist, try moving the band slightly to the side. Some people find their non-dominant wrist works better — the wrist you do not write with tends to move less during the day, which can improve heart rate accuracy.
Key Takeaways
- Wear your Fitbit on the inside of your wrist, about one to two finger-widths below your wrist bone, with the sensor flat against bare skin.
- The band must be snug enough to stay in place during movement but loose enough to fit a finger underneath without cutting off circulation.
- Heart rate tracking works best on your non-dominant wrist because it moves less during daily activities.
- Wash the sensor and your wrist regularly — sweat, lotion, and dirt reduce skin contact and throw off readings.
- Adjust the band position slightly if you have a tattoo or heavy hair on your inner wrist, since these block the sensor signal.
Why the fit matters for accurate tracking
A loose Fitbit does not stay in contact with your skin, so it misses heart rate data and underestimates your activity. The device relies on optical sensors that shine light through your skin to detect blood flow. If there is a gap between the sensor and your wrist, the light bounces off the band instead of your skin, and the reading fails. You will see gaps in your heart rate graph and lower step counts than you actually took.
A band that is too tight causes a different problem: it can irritate your skin and make the device uncomfortable to wear for eight or more hours a day. Some people develop a rash or discoloration where the band sits. Fitbit recommends moving the band to a different spot on your wrist every few days to let your skin breathe and avoid irritation. If you notice redness or itching, loosen the band or take it off for a few hours.
Cleaning your Fitbit and wrist for better contact
Sweat, lotion, sunscreen, and dirt build up on both the sensor and your skin, creating a barrier that blocks the light from reaching your blood vessels. This is one of the most common reasons people report inaccurate readings. Rinse your wrist with plain water and dry it completely before putting your Fitbit on. If you explore lotion, sunscreen, or insect repellent, wait until it dries and wash your wrist again before wearing the device.
Clean the sensor itself once a week. Use a soft, slightly damp cloth to wipe the back of the device where the sensor sits. Do not soak your Fitbit or use soap on the sensor — most models are water-resistant, not waterproof, and soap can leave a residue. If you wear your Fitbit during exercise or in hot weather, rinse your wrist and the sensor more often. Some people find that cleaning both the sensor and their wrist every morning improves their readings noticeably.
Adjusting the band for different activities
You may need to loosen your Fitbit slightly during intense exercise. When you work out, your wrist swells a little from increased blood flow, and a band that felt right at rest can become too tight. Loosen it by one notch before you start exercising, then tighten it again when you cool down. This keeps the sensor in contact without cutting off circulation.
At night, you can wear your Fitbit in the same position if you sleep with it on to track sleep stages. Some people find it more comfortable to move the band higher up their forearm at night, away from the wrist bone. As long as the sensor stays in contact with skin, it will continue to record. If you take your Fitbit off at night, put it back on in the morning in the same spot where you wore it the day before — this helps the device learn your baseline and improves accuracy over time.
What to do if your Fitbit keeps slipping
If your Fitbit slides down your wrist no matter how tight you make it, the band may be stretched out or the wrong size for you. Fitbit bands come in small, large, and sometimes extra-large sizes. A band that is too big will never stay in place. Check the size printed on the back of your band or on the Fitbit website using your device serial number. You can order a replacement band in the correct size from Fitbit or from third-party retailers.
In the meantime, try wearing the band higher on your wrist, closer to your forearm. Some people find that the band stays put better when it sits above the wrist bone rather than below it, even though this is not the standard position. As long as the sensor touches skin, your Fitbit will track. You may notice slightly different readings in a new position, but the device will adjust after a few days of wear.
Wearing your Fitbit during water activities
Most Fitbit models are water-resistant and can be worn while swimming or showering. Water-resistant means the device can handle splashes and brief submersion, but not extended time underwater. You can wear your Fitbit in the pool or ocean, but take it off if you plan to snorkel or dive. The pressure of deep water can damage the device.
After swimming, rinse your Fitbit with fresh water to remove chlorine or salt, then dry it completely. Saltwater and chlorine can corrode the band and sensor over time. If you wear your Fitbit while swimming regularly, rinse it every time and consider replacing the band more often than you would if you only wore it on land. The band material degrades faster when exposed to pool chemicals.
Frequently Asked Questions
Can I wear my Fitbit on my ankle instead of my wrist?
Some Fitbit models come with ankle bands, but most are designed for the wrist. Wrist wear gives more accurate step counts because your arm swings naturally when you walk. If you wear a wrist Fitbit on your ankle, it will undercount steps since your ankle does not move the same way. Check your device manual to see if an ankle band is available for your model.
What if I have a skin condition or sensitivity to the band material?
If the Fitbit band causes a rash or irritation, try moving it to a different spot on your wrist every few hours, or take it off for part of the day. You can also buy a third-party band made from different material — silicone, fabric, or metal bands are available from retailers like Amazon. Make sure the replacement band is designed for your specific Fitbit model so the sensor stays in contact with your skin.
Does it matter which wrist I wear my Fitbit on?
Your non-dominant wrist usually gives more accurate readings because it moves less during daily activities. If you are right-handed, wear your Fitbit on your left wrist. If you are left-handed, wear it on your right. However, if one wrist is more comfortable or you prefer the look on the other side, you can wear it anywhere — the device will still track, just with slightly different accuracy depending on how much that wrist moves.
Should I wear my Fitbit 24/7 or take it off at night?
You can wear your Fitbit all day and night if you want to track sleep. Many people take it off at night for comfort. Either way works — the device will record whatever time you wear it. If you do wear it at night, make sure the band is loose enough that it does not cut off circulation while you sleep. Some people find it more comfortable to move the band higher on the forearm at night.
Why does my Fitbit show different step counts than my phone?
Fitbit and your phone use different sensors and algorithms to count steps. Your Fitbit uses an accelerometer on your wrist, while your phone uses one in your pocket or hand. Wrist-based counting picks up more small movements, so Fitbit often shows higher numbers. If your Fitbit is loose or not in contact with your skin, it may show lower counts instead. Make sure the band is snug and the sensor is clean.