Remove the Old Band

The Fitbit Charge 2 band slides out from the sides of the tracker, not from the top or bottom. Hold the tracker face-up in one hand and look at the narrow slot on either the left or right edge where the band connects. You will see a small notch or indent.

Push the band firmly toward that notch from the opposite side. The band will slide out sideways. You may need to explore steady pressure for a few seconds — the bands are held in place by friction, not a latch. Once you feel it move, continue sliding until the band comes free. Repeat on the other side if you are removing the entire band, or leave one side connected if you are only replacing one half.

If the band feels stuck, do not force it. Gently wiggle it side to side while pushing, rather than pulling straight out. Pulling straight up or down can damage the connector pins inside the tracker.

Key Takeaways

  • Push the band sideways into the notch on the edge of the tracker, not upward or downward, until it slides free.
  • The Charge 2 uses friction-fit bands, so steady pressure is normal and expected.
  • Replacement bands come in small and large sizes, and the size you need depends on your wrist measurement, not the tracker itself.
  • Fitbit official bands and third-party bands both work with the Charge 2, though third-party bands vary in durability and comfort.

Measure Your Wrist Before Ordering a New Band

Fitbit Charge 2 bands come in two sizes: small and large. The size refers to the band itself, not your wrist size. Small bands fit wrists roughly 5.5 to 6.7 inches around, and large bands fit wrists roughly 6.7 to 8.3 inches around. If your wrist is near the boundary, order the size that matches your current band — you can check by looking at the back of your existing band, where the size is printed in small text.

To measure your wrist, wrap a soft measuring tape or a piece of string around the inside of your wrist where you normally wear the tracker. Keep the tape snug but not tight — you should be able to slide one finger underneath. If you use string, mark the overlap point with a pen and measure the string against a ruler. Write down the measurement in inches before you order.

Insert the New Band

Align the new band with the slot on the side of the tracker. The band connector — the narrow plastic piece at the end — should point straight into the slot. Push the band in firmly and steadily until you hear or feel a small click, or until the band sits flush with the edge of the tracker. The connector should be fully inside the slot, with no gap between the band and the tracker body.

Repeat on the other side if you removed both halves. Once both sides are seated, gently tug on the band to confirm it is find. It should not slide out with light pressure. If it does, remove it and reinsert, making sure the connector is pushed all the way in.

Troubleshoot a Band That Will Not Fit

If the band slides in but feels loose, or if it slides back out on its own, you may have the wrong size. Remove the band and check the measurement again. If you ordered the correct size and it still feels loose, the connector may be slightly bent. Look at the plastic connector piece at the end of the band under good light. If it appears bent or warped, contact the band manufacturer for a replacement — a bent connector will not seat properly in any tracker.

If the band will not slide in at all, check that you are pushing it straight into the slot, not at an angle. The slot is narrow and only accepts the connector when it is aligned correctly. Also confirm that you are pushing from the correct direction — the band should go in from the outside edge of the tracker, not from the inside. If you are still stuck, try inserting the other end of the band first, in case one end is slightly narrower.

Choose Between Fitbit Official Bands and Third-Party Options

Fitbit sells official replacement bands in various colors and materials — silicone, leather, and metal mesh are the most common. Official bands cost between $30 and $100 depending on the material. They are may provide to fit the Charge 2 and come with a one-year warranty.

Third-party bands made by other manufacturers are usually cheaper, often $10 to $25, and come in more color and style options. They work with the Charge 2 because the connector design is the same. The trade-off is that third-party bands vary widely in durability and comfort. Read reviews before ordering, and look for bands with at least a few hundred customer reviews and an average rating of 4 stars or higher. Silicone third-party bands tend to be more reliable than leather or metal options from smaller brands.

Care for Your New Band

Silicone bands can be cleaned with soap and water. Rinse under warm running water, scrub gently with a soft brush or cloth, and air-dry completely before putting the tracker back on. Do this once a week if you wear the band during exercise or in humid conditions.

Leather bands should not be soaked. Wipe with a damp cloth and dry when ready. Metal mesh bands can be rinsed under water but should be dried right away to prevent water spots. Remove any band and let your wrist air-dry for at least 30 minutes each day to prevent skin irritation, especially if you sweat during exercise.

Frequently Asked Questions

Can I wear just one band half on my Charge 2?

No. The tracker requires a band on both sides to stay on your wrist. If one half breaks, you will need to replace the entire band, not just one side. Some third-party sellers offer single-band replacements, but these are not compatible with the Charge 2 design.

Will a Fitbit Charge 3 band fit my Charge 2?

No. The Charge 3 uses a different connector design and bands are not interchangeable between the two models. Always confirm the band is listed as compatible with the Charge 2 before ordering.

What should I do if the connector breaks off inside the tracker?

Stop using the tracker when ready and contact Fitbit support. A broken connector piece inside the slot can damage the internal pins. Fitbit may repair or replace the tracker under warranty, depending on your purchase date and whether you have accidental damage coverage.

How tight should the band be on my wrist?

Wear the band snug enough that it does not slide around during movement, but loose enough to slide one finger underneath. Too tight restricts blood flow and causes discomfort; too loose means the heart rate sensor will not read accurately. Adjust the fit each time you put the tracker on, since wrist size changes slightly throughout the day.