The Charge 2 band slides out from the side, not the bottom

The Fitbit Charge 2 band is held in place by a small pin on each side of the watch face. To remove it, you push the band away from the watch body — not down or up — until the pin clears the slot. The band then slides out sideways. This design is different from some other Fitbit models, so if you've owned a different one before, the motion might feel unfamiliar at first.

You do not need tools, and you do not need to remove the watch from your wrist to do this, though many people find it easier to work on a flat surface. The whole process takes about 30 seconds once you know which direction to push.

Key Takeaways

  • Push the band away from the watch face (toward the outer edge of your wrist) until the pin clears the slot on each side.
  • The band slides out sideways once both pins are free; it does not pop out suddenly.
  • Replacement bands are sold by Fitbit and by third-party makers, and they cost between $15 and $40 depending on material and brand.
  • The new band slides in the same way the old one came out — line up the pin holes and push the band toward the watch face until you hear or feel a click.

Step 1: Position the watch and locate the pins

Hold the Charge 2 so you can see the side of the watch face clearly. You will see a small slot on each side where the band connects. Inside each slot is a tiny pin that holds the band in place. The pins are usually silver or black and are about the size of a pencil tip.

If you are wearing the watch, you can do this on your wrist, but most people find it easier to set the watch on a table or hold it in one hand while working with the other. Make sure you have good light so you can see the pins clearly.

Step 2: Push the band away from the watch face

Grip the band firmly but gently. Using your thumb or index finger, push the band away from the watch face — in the direction that would move it toward the outer edge of your wrist if you were wearing it. You are pushing the band outward, not pulling it down or twisting it.

Push steadily until you feel the pin on that side clear the slot. You will usually feel a slight resistance, then a small give as the pin comes free. Repeat this on the other side. Once both pins are clear, the band will slide out sideways without any force. If it feels stuck, you are probably pushing in the wrong direction — try pushing the opposite way.

Step 3: Slide in the new band and find both sides

Line up the new band so the pin holes on the band match the slots on the watch face. Slide the band in from the side, pushing it toward the watch face until the pins seat fully in the slots. You should hear or feel a small click as each pin locks into place. The band should not move side to side once it is installed.

Test the band by gently trying to wiggle it. If it moves, the pins are not fully seated — push it in a bit further until it stops. Once it is find, the band is ready to wear.

Where to buy replacement bands

Fitbit sells official Charge 2 bands on their website and through retailers like Amazon and Best Buy. Official bands come in leather, fabric, and silicone, and cost between $25 and $40. They are may provide to fit and are backed by Fitbit's warranty.

Third-party bands made by companies like Wearlizer, Mornex, and Havill are also available and usually cost $15 to $25. These work with the Charge 2 and come in many colors and materials, though quality varies by maker. Read reviews before buying a third-party band to make sure the pins fit snugly in the slots — a loose fit can cause the band to fall off during wear.

What to do if the pin breaks or the band won't stay in

If a pin breaks off inside the watch, you will need to contact Fitbit support or take the watch to a repair shop. The pin is small and difficult to remove without damaging the watch. Fitbit may replace the watch under warranty depending on how long you have owned it.

If a new band keeps sliding out, the pins on that band may be slightly too small or the slots on your watch may be worn. Try a different band first to rule out a problem with the watch itself. If multiple bands fall out, contact Fitbit — the watch may need repair.

Frequently Asked Questions

Can I wear the Charge 2 without a band?

No. The band holds the watch face to the strap that goes around your wrist. Without a band, you have only the watch face, which cannot be worn. You need a band to use the watch.

Do I have to take the watch off my wrist to change the band?

No. You can change the band while wearing the watch if you have steady hands and good light. Many people find it easier to set the watch on a table, but it is not required.

What if I lose one of the bands that came with my Charge 2?

The Charge 2 comes with one band. If you lose it, you will need to buy a replacement band from Fitbit or a third-party maker. Fitbit does not sell the original band separately, so a replacement will be a different style or color.

Are Charge 2 bands the same size as bands for other Fitbit models?

No. Charge 2 bands are not compatible with Charge 3, Charge 4, Charge 5, or other Fitbit models. Each model has different pin spacing and slot sizes. Make sure you buy a band made specifically for the Charge 2.

Can I use a regular watch band on my Charge 2?

No. The Charge 2 uses a proprietary pin system that is different from standard watch bands. Only bands made for the Charge 2 will fit and work correctly.