Remove the Old Band in Two Steps
The Fitbit Charge 2 band slides out from the sides of the tracker, not the top or bottom. Hold the device face-up in one hand. With your other hand, push the band firmly toward the center of the tracker from either the left or right side — you will feel it click and release. Once one side pops free, slide the band all the way out.
If the band feels stuck, do not force it. The release mechanism works best when you push straight inward rather than at an angle. A small amount of pressure is enough; the band should come free with a distinct click. If it does not budge after gentle pressure, the tracker may have a manufacturing defect, but this is rare.
Key Takeaways
- Push the band inward from the side (not the top or bottom) until it clicks and releases from the tracker body.
- Fitbit Charge 2 bands are interchangeable with other Charge 2 devices, so any official or third-party Charge 2 band will fit your tracker.
- The tracker itself stays dry during band changes, so you can swap bands anywhere without worrying about water damage.
- Replacement bands come in small, large, and extra-large sizes — measure your wrist or check the size marking on your current band before ordering a new one.
Slide the New Band Into Place
Take your new band and align it with the empty slot on the tracker. The band should slide in smoothly from the side, the same direction you removed the old one. Push it in firmly until you hear or feel a click — this means the band is locked in place and will not slip out during wear.
Test the connection by gently tugging the band from both sides. It should not move. If the band slides back out easily, remove it and try again, making sure you push all the way in until the click happens. A properly seated band will be snug enough that you cannot pull it free by hand.
Check Your Band Size Before Ordering
Fitbit Charge 2 bands come in three sizes: small, large, and extra-large. Your current band has a size marking printed on the inside surface — look at the underside where it touches your skin. The size will be a single letter: S, L, or XL.
If you cannot find the marking or your current band does not fit well, measure your wrist with a soft measuring tape. Small bands fit wrists 5.5 to 6.7 inches around, large bands fit 6.7 to 8.1 inches, and extra-large bands fit 8.1 inches and above. When in doubt, order the size that matches your current band — it was sized correctly from the factory.
Understand Which Bands Work With Your Tracker
Any band made for the Fitbit Charge 2 will work with your device, whether it is an official Fitbit band or a third-party replacement. The connection mechanism is the same across all Charge 2 models. Bands made for other Fitbit devices — the Charge 3, Charge 4, Inspire, or Flex — will not fit because the slot width and release mechanism are different.
Official Fitbit bands typically cost between $25 and $35 per band. Third-party bands are often cheaper, ranging from $10 to $20, and many reviewers report they last as long as official bands. Both types come in a wide range of colors and materials, including silicone, leather, and woven fabric.
Care for Your Tracker While the Band Is Off
The Fitbit Charge 2 tracker itself is water-resistant, so it is safe to wear without a band or to clean it while the band is removed. If you want to wash the tracker body, use a soft, damp cloth and dry it thoroughly before putting a new band on. Do not submerge the tracker in water or use soap directly on the device.
Store removed bands in a cool, dry place. Silicone bands can develop odor over time if stored damp, so make sure they are completely dry before putting them away. If you plan to swap bands regularly — for example, wearing a sport band during the week and a leather band on weekends — keeping multiple bands on hand means you can change them as often as you like without waiting for shipping.
Troubleshoot a Band That Will Not Stay In
If your new band keeps sliding out after you insert it, the most common cause is not pushing it in far enough. Remove the band and try again, explore steady pressure until you feel the click. The click is the signal that the locking mechanism has engaged.
If the band still will not lock after several attempts, inspect the slot on the tracker for debris — lint, dust, or dried sweat can prevent the band from seating fully. Use a dry cloth or a soft brush to clean out the slot, then try inserting the band again. If the band still does not lock, the tracker may have a defective slot, and you should contact Fitbit support with the device serial number and purchase date.
Frequently Asked Questions
Can I wear my Fitbit Charge 2 without a band?
Yes, the tracker itself is water-resistant and will continue to track your steps, heart rate, and sleep without a band. However, wearing it without a band makes it more likely to slip off your wrist or get damaged if dropped. Most people wear a band for comfort and security.
How often should I replace the band?
A silicone band typically lasts 12 to 18 months with daily wear before the material begins to crack or lose elasticity. Leather and woven bands may wear out faster depending on how often you wear them and how much you expose them to sweat or water. Replace the band whenever it becomes uncomfortable or visibly damaged.
What if I lose my band and need a temporary replacement?
You can order a replacement band from Fitbit's website or from third-party retailers like Amazon. Shipping usually takes 3 to 7 business days. In the meantime, you can wear the tracker without a band or use a sports armband designed for fitness trackers as a temporary holder.
Do I need to remove my band before swimming?
No, the Fitbit Charge 2 and its bands are water-resistant up to 50 meters, which means they can handle swimming and snorkeling. However, salt water and chlorine can degrade silicone bands over time, so rinse your band with fresh water after swimming in a pool or ocean.
Can I use a Charge 2 band on a different Fitbit model?
No, Charge 2 bands only fit the Charge 2. The Charge 3, Charge 4, Inspire, and Flex all use different band connectors. If you upgrade to a newer Fitbit model, your current bands will not work with the new device.