Clean your Fitbit with a soft, damp cloth and mild soap—never submerge it or use harsh chemicals
Your Fitbit tracks sweat, dirt, and skin oils every day, so regular cleaning keeps it working properly and prevents skin irritation. The safest method is a soft, lint-free cloth slightly dampened with water and a drop of mild dish soap. Wipe the band, the face, and the underside where the sensors sit. Dry it completely with a clean cloth before wearing it again. This takes about two minutes and should happen at least once a week, or more often if you exercise daily or live in a humid climate.
Never soak your Fitbit, use rubbing alcohol, bleach, or abrasive scrubbers. Even though most Fitbit models are water-resistant, they are not waterproof—water can seep into the charging contacts or the seams around the screen and cause permanent damage. The same goes for high-pressure water from a shower or faucet. Gentle hand-washing is all you need.
Key Takeaways
- Use only a soft, damp cloth with mild dish soap; never soak the device or use harsh chemicals.
- Pay special attention to the underside of the band and the sensor area, where sweat and dirt accumulate most.
- Dry the Fitbit completely with a clean cloth before putting it back on your wrist.
- Clean your Fitbit at least once a week, or more often if you exercise regularly or sweat heavily.
- Avoid submerging the device, using rubbing alcohol or bleach, or scrubbing with rough materials.
Cleaning the Band and Strap
The band collects the most dirt because it sits against your skin all day. Remove the band from the watch face if your model allows it—many Fitbit bands are designed to slide out or unclip. Check your device manual or the Fitbit website to confirm whether your specific model has a removable band.
Dampen a soft cloth with lukewarm water and add one small drop of mild dish soap. Wipe the entire band, paying extra attention to the underside that touches your skin. Use a second cloth dampened with plain water to rinse away any soap residue. Lay the band flat on a clean, dry towel and let it air-dry completely—at least 30 minutes—before reattaching it. If your band is not removable, wipe it in place using the same damp cloth method, then dry it thoroughly.
If the band smells or shows visible mold, soak it in a mixture of equal parts white vinegar and water for 15 minutes, then rinse and dry. Do not soak the watch face itself, only the band.
Cleaning the Watch Face and Screen
The screen and face collect fingerprints, dust, and dried sweat. Use a soft, lint-free cloth—microfiber cloths work best—slightly dampened with plain water. Gently wipe the screen in circular motions. If the screen is very dirty, add one tiny drop of mild dish soap to the cloth, wipe the screen, then when ready wipe again with a cloth dampened in plain water only.
Never spray liquid directly onto the screen or face. Never use paper towels, tissues, or rough cloths, which can scratch the display. Dry the screen completely with a clean, dry cloth before wearing the device again. If your Fitbit has a protective film or tempered glass screen protector, follow the same method—the protector is designed to take the wear instead of the actual screen.
Cleaning the Sensors and Charging Contacts
The sensors on the underside of your Fitbit and the charging contacts are the most delicate parts. These are where the device reads your heart rate and where the charger makes electrical contact. Dirt or corrosion here can cause the device to stop charging or give inaccurate readings.
Use a soft, dry cloth to gently wipe the underside of the watch face and the sensor area. If there is visible dirt or dried sweat, dampen the cloth very slightly with plain water—it should be barely damp, not wet. Wipe gently and dry when ready with a separate dry cloth. Never use soap on the sensors or charging contacts. If the charging contacts look corroded or discolored, try rubbing them very gently with a dry cloth first. If that does not work, contact Fitbit support before attempting any other cleaning method.
Drying Your Fitbit Properly
Incomplete drying is the most common cause of water damage. After cleaning, use a clean, dry cloth to wipe the entire device—band, face, underside, and charging contacts. Then let it air-dry for at least 15 to 30 minutes in a warm, dry place before wearing it again or putting it on the charger.
Do not use a hair dryer, heat lamp, or direct sunlight to speed up drying. Heat can damage the battery and the screen. If you just cleaned the band and removed it from the watch, dry both pieces separately and let them sit apart until completely dry. This prevents moisture from being trapped between the band and the watch face.
Cleaning Your Fitbit Charger
The charger also needs regular cleaning, especially the metal contacts that touch your Fitbit. Dirt or corrosion on the charger contacts prevents the device from charging properly. Use a dry, soft cloth to wipe the metal contacts on the charger cable. If the contacts look discolored or corroded, dampen the cloth very slightly with plain water and rub gently, then dry when ready.
Never soak the charger or expose it to water. Store the charger in a dry place when not in use. If the charger stops working after cleaning, do not attempt further repairs—contact Fitbit support for a replacement.
How Often to Clean and What to Avoid
Clean your Fitbit at least once a week with the damp cloth method. If you exercise daily, sweat heavily, or live in a humid or salty environment (like near the ocean), clean it two or three times a week. After swimming or showering, wipe it down when ready, even if you did not fully submerge it.
Never use rubbing alcohol, hand sanitizer, bleach, vinegar (except on the band only, in the special soak method), acetone, or any solvent. These damage the screen, the band material, and the internal components. Do not scrub with a toothbrush, steel wool, or any rough material. Do not use ultrasonic cleaners, which can force water into sealed areas. Do not expose your Fitbit to extreme heat or cold while cleaning or drying.
Frequently Asked Questions
Can I clean my Fitbit under running water?
No. Running water from a faucet or shower can force water into the seams and damage the device, even though Fitbit models are water-resistant for swimming or light rain. Always use a damp cloth instead. If water does get inside, remove the band, dry the device completely, and let it sit in a warm, dry place for 24 hours before charging or wearing it again.
What should I do if my Fitbit stops charging after I cleaned it?
The charging contacts may still be wet or corroded. Remove the band, dry the underside of the watch and the charger contacts thoroughly with a clean, dry cloth, and let everything air-dry for at least one hour. Try charging again. If it still does not charge, contact Fitbit support—do not attempt to clean the contacts further.
Is it safe to clean my Fitbit with a disinfectant wipe?
Most disinfectant wipes contain alcohol or bleach, which can damage the screen and band material. Stick to a soft cloth with plain water and a tiny drop of mild dish soap. If you want to disinfect the band, soak it in equal parts white vinegar and water for 15 minutes, then rinse and dry thoroughly.
How do I remove stubborn sweat stains from the band?
Soak the band (not the watch face) in a mixture of equal parts white vinegar and water for 15 minutes. Scrub gently with a soft cloth, rinse with plain water, and air-dry completely. For persistent stains, repeat the soak. If the stain does not come out, the band material may be permanently discolored, but this does not affect how the device works.
Can I wear my Fitbit while cleaning it?
No. Remove the Fitbit and set it aside on a clean surface before you start cleaning. This prevents accidental damage and lets you clean the underside and charging contacts thoroughly. Wait until it is completely dry before putting it back on.