Your Fitbit heart rate sensor stops working for one of five reasons: a loose or dirty band, outdated firmware, a syncing problem between the device and your phone, a hardware failure, or settings that have turned the feature off

The heart rate monitor on your Fitbit is an optical sensor on the back of the device that reads blood flow through your wrist. It needs direct skin contact, a snug fit, and a clear connection to your phone to report readings. When it stops working, the issue is almost always something you can fix in five minutes — but occasionally it means the sensor itself has failed and the device needs replacement.

Start by checking the most common culprits: whether your band is loose, whether your firmware is current, and whether your device is syncing properly with the Fitbit app. If those three things check out, move to the sensor itself and the app settings. This guide walks you through each step in order.

Key Takeaways

  • A loose or dirty band is the single most common reason the heart rate sensor stops reading — the sensor needs direct skin contact to work.
  • Your Fitbit firmware must be up to date for the heart rate feature to function; check for updates in the Fitbit app under your device settings.
  • The device must sync with your phone within the last few hours for heart rate data to appear in the app, even if the sensor is working.
  • If the sensor is physically damaged or the optical lens is cracked, the device cannot be repaired and will need to be replaced.
  • Turning off heart rate tracking in the app settings will hide readings even though the sensor is still working.

Check that your band is snug and the sensor is clean

The optical heart rate sensor on the back of your Fitbit works by shining light through your skin and measuring how much bounces back. If the band is loose, the sensor loses contact with your wrist and cannot take a reading. If the sensor lens is dirty, the light cannot pass through clearly.

Tighten your band so it sits snugly on your wrist — you should be able to fit one finger underneath it, but not two. The band should not slide around when you move your arm. Then use a soft, dry cloth to wipe the back of the device where the sensor sits. Do not use water or cleaning solution; a dry microfiber cloth or the corner of a cotton shirt is enough.

Wear the device for five minutes after tightening and cleaning, then open the Fitbit app and check whether heart rate readings appear. If readings show up, the problem was the fit or dirt. If not, move to the next step.

Update your Fitbit firmware to the latest version

Fitbit releases firmware updates regularly, and the heart rate feature will not work if your device is running an outdated version. Firmware is the software that runs on the device itself, separate from the app on your phone.

Open the Fitbit app on your phone and tap your profile picture in the top left corner. Select your device from the list. Scroll down and look for a section called "Device" or "About." If an update is available, you will see a button that says "Update" or "Install Update." Tap it and leave your device near your phone while it installs — this usually takes two to five minutes. Do not close the app or move the device away until the update finishes.

After the update completes, restart your Fitbit by holding the button on the side for ten seconds until the screen goes dark, then release. Wait thirty seconds and press the button again to turn it back on. Check the app again to see whether heart rate readings have returned.

Force a sync between your device and the Fitbit app

Your Fitbit stores heart rate data on the device itself, but the app only displays data that has been synced from the device to your phone. If the device has not synced in several hours, the app will show no recent heart rate readings even though the sensor is working.

Open the Fitbit app and tap your profile picture. Select your device. At the bottom of the screen, you should see a "Sync Now" button or a circular sync icon. Tap it. The app will attempt to connect to your device wirelessly — this takes about thirty seconds. Make sure your phone's Bluetooth is turned on and that you are within ten feet of your Fitbit.

After the sync completes, open the heart rate section of the app (usually under "Heart Rate" or "Today") and check whether readings appear. If you see data, the sensor was working but the device was not syncing. If you still see no readings, continue to the next step.

Verify that heart rate tracking is not turned off in settings

The Fitbit app has a setting that allows you to turn off heart rate tracking entirely. If this setting is disabled, the app will not display heart rate data even though the sensor is still collecting it.

Open the Fitbit app and tap your profile picture. Select your device. Scroll down to find "Heart Rate" or "Heart Rate Settings." Make sure the toggle next to it is turned on (it should be blue or green, not gray). If it is off, tap it to turn it back on.

Some Fitbit models also have a heart rate setting on the device itself. Press the button on your device to cycle through the screens until you see a heart icon. If the heart icon has a line through it, the feature is disabled on the device. Press the button again to enable it.

Restart your Fitbit and your phone

A restart clears temporary glitches that can prevent the device and app from communicating properly. This step fixes the problem in roughly one out of every three cases where the earlier steps have not worked.

First, restart your Fitbit: hold the button on the side for ten seconds until the screen goes dark, then release. Wait thirty seconds and press the button again. Next, restart your phone by powering it off completely and turning it back on. This takes about two minutes total.

After both devices have restarted, open the Fitbit app, force a sync, and check whether heart rate readings appear. If they do, the problem was a temporary software glitch. If not, the issue is likely with the sensor hardware itself.

Determine whether the sensor is physically damaged

If you have worked through all the steps above and heart rate readings still do not appear, the optical sensor on the back of your device may be damaged. Look at the back of your Fitbit under bright light. The sensor is a small dark circle, usually about the size of a pencil eraser. Check whether the lens is cracked, cloudy, or visibly damaged.

If the lens is cracked or severely cloudy, the sensor cannot be repaired and the device will need to be replaced. Fitbit does not sell replacement sensors for individual devices. If your device is still under warranty (usually one year from purchase), you may be able to contact Fitbit support to request a replacement. If it is out of warranty, you will need to purchase a new device.

If the lens looks clear and undamaged but heart rate readings still do not appear, the sensor may have an internal failure that is not visible from the outside. In this case, contact Fitbit support with the model number of your device (found in the app under your device settings) and a description of the steps you have taken. They can determine whether the device qualifies for replacement.

Frequently Asked Questions

Why does my Fitbit show a heart rate sometimes but not other times?

An intermittent heart rate reading usually means the band is loose or the sensor is not making consistent contact with your skin. Tighten the band and make sure it does not slide around during movement. If readings are intermittent during exercise, the band may be bouncing on your wrist — try moving it higher up your forearm, closer to your elbow, where there is less movement.

Can I use my Fitbit without the heart rate monitor?

Yes. You can turn off heart rate tracking in the app settings and your Fitbit will still track steps, distance, calories, and sleep. The device will continue to work normally for all other features. Some older Fitbit models do not have a heart rate sensor at all and function perfectly fine without it.

Does my Fitbit need to be connected to WiFi for the heart rate to work?

No. The heart rate sensor works entirely on the device itself and does not require an internet connection. It only needs Bluetooth to sync the data to your phone so you can see it in the app. The sensor will collect heart rate data even if Bluetooth is off, but the app will not display it until you sync.

What if my Fitbit is wet — could that be why the heart rate is not working?

Most Fitbit models are water-resistant but not waterproof, and water can interfere with the optical sensor. If your device got wet, remove it and let it dry completely in a warm, dry place for at least two hours. Do not use heat like a hair dryer. After it dries, try the heart rate feature again. If it still does not work, water may have damaged the sensor permanently.

How do I know if my Fitbit is too old to get firmware updates?

Open the Fitbit app, go to your device settings, and check the "About" section. If it shows your current firmware version but no update button appears, your device is running the latest version available for that model. Fitbit stops releasing updates for devices that are more than five to seven years old. If your device is very old and the heart rate feature is not working, an update will not fix it.