The Basic Connection: What Goes Where

Your modem and router are two separate devices that work together. The modem connects to your internet service provider's line (cable, fiber, or DSL) and converts that signal into data your devices can use. The router takes that data from the modem and broadcasts it wirelessly to your phones, laptops, and other devices. To connect them, you run an ethernet cable from the modem's output port to the router's input port — usually labeled "WAN," "Internet," or "Uplink."

The physical connection itself takes about two minutes. The setup that follows — naming your network and setting a password — takes another five to ten minutes. After that, your devices can find and join your wireless network.

Key Takeaways

  • Connect an ethernet cable from your modem's output port to your router's WAN or Internet port; this is the only cable that goes between them.
  • Power on the modem first and wait for its lights to stabilize (usually two to three minutes), then power on the router.
  • Once the router's lights show it is connected, open a web browser and visit your router's setup page — usually 192.168.1.1 or printed on the router's label.
  • Create a network name (SSID) and password during setup; write these down so you can share them with household members and guests.
  • If your router does not connect after ten minutes, restart both devices by unplugging them for 30 seconds, modem first.

What You Need Before You Start

Gather these items before you begin: your modem, your router, one ethernet cable (usually included with the router), and power cords for both devices. The ethernet cable is a thin cord with plastic connectors on each end — it looks similar to a phone cord but slightly wider. If your router did not come with one, any standard ethernet cable works.

You will also need a device with a web browser — a laptop, tablet, or phone — to set up the router's wireless network name and password. This device does not need to be connected to the internet yet; you will connect it to the router's temporary setup network during the process.

Step-by-Step Connection Process

Step 1: Position your devices. Place your modem and router near each other, ideally within a few feet. This makes the ethernet cable easier to run and keeps both devices in a well-ventilated spot. Avoid stacking them directly on top of each other, as heat buildup can shorten their lifespan.

Step 2: Connect the ethernet cable. Plug one end of the ethernet cable into the port on the back of your modem labeled "Ethernet Out," "LAN," or sometimes just a numbered port. Plug the other end into the port on your router labeled "WAN," "Internet," "Uplink," or sometimes "Port 1." The cable should click into place. This is the only cable that connects the two devices — do not plug anything else between them.

Step 3: Power on the modem. Plug the modem's power cord into an outlet and press the power button if it has one. Wait two to three minutes for the modem's lights to stop blinking and settle into a steady pattern. You should see lights for power, internet connection, and ethernet activity. If the internet light does not turn on after five minutes, your modem may not be receiving a signal from your provider — contact them to confirm service is active at your address.

Step 4: Power on the router. Once the modem's lights are stable, plug in the router's power cord. The router will take one to two minutes to boot up. You should see lights turn on for power and internet connection. Some routers also have a light for wireless activity. Once these lights are steady, your router is connected to the modem.

Step 5: Set up your wireless network. On your laptop, phone, or tablet, look for available wireless networks. You should see your router's default network name (often something like "NETGEAR-1234" or "TP-Link-5G"). Connect to it — you may be prompted for a password, which is usually printed on a sticker on the router's bottom or back. Once connected, open a web browser and visit the address printed on that same sticker, usually 192.168.1.1 or 192.168.0.1. This opens your router's setup page. Follow the prompts to create your own network name and password. Write these down and keep them somewhere safe.

Troubleshooting If Your Router Does Not Connect

If the router's internet light does not turn on after five minutes, the ethernet cable may not be fully inserted. Unplug both ends and plug them back in firmly until you hear a click. Check that you are using the correct ports — the cable must go from the modem's output to the router's WAN or Internet port, not to a regular LAN port on the router.

If the cable is seated correctly but the router still shows no connection, restart both devices. Unplug the modem's power cord, wait 30 seconds, and plug it back in. Once its lights are stable again, unplug the router, wait 30 seconds, and plug it back in. This clears temporary errors and usually restores the connection within two minutes.

If you still have no connection after restarting, the ethernet cable itself may be damaged. Try a different cable if you have one. If a different cable works, the original cable is faulty and should be replaced. If neither cable works, contact your internet service provider — the issue may be on their end, or your modem may need service.

Positioning Your Router for the Best Wireless Signal

Once your router is connected and set up, where you place it affects how well your wireless network reaches throughout your home. Put the router in a central, elevated location — a shelf or wall mount in a hallway or living room works better than a closet or corner. Avoid placing it inside cabinets, behind appliances, or in basements, as walls and metal objects block the signal.

Keep the router away from other electronics that use radio frequencies, such as microwave ovens, cordless phones, and baby monitors. These devices can interfere with your wireless signal and slow your connection. If your router has external antennas, position one vertically and one horizontally to broadcast in different directions.

When to Call Your Internet Service Provider

If your modem never shows an internet connection light, even after restarting, contact your internet service provider. They can confirm that service is active at your address and may need to send a technician to check the line coming into your home. If your modem connects but your router cannot connect to the modem, the router may be faulty — check the manufacturer's warranty and contact their support line.

If you connect to the router's wireless network but cannot reach any websites, the issue is usually with the router's setup. Return to the setup page (192.168.1.1 or the address on your router) and confirm that the internet connection is showing as active. If it is, restart the router. If the problem persists, contact your router's manufacturer — most have phone support or live chat on their website.

Frequently Asked Questions

Can I use a different ethernet cable than the one that came with my router?

Yes. Any standard ethernet cable works. The cable that comes with your router is just a convenience. If you need a longer cable to reach across a room, any ethernet cable of any length will work the same way.

What if my router does not have a WAN port?

Some older or very basic routers label all ports the same. If you cannot find a WAN or Internet port, check the manual or the manufacturer's website. Usually, one port is designated as the input port and the others as output ports. The manual will tell you which one. If the manual is lost, the manufacturer's support page has this information.

Do I need to restart my modem and router every time I restart my computer?

No. Once they are connected and set up, they stay connected. You only restart them if your internet stops working or if you are troubleshooting a problem. Restarting your computer does not affect the modem or router.

Can I connect my router to the modem with WiFi instead of an ethernet cable?

Most routers cannot connect to a modem wirelessly. The ethernet cable is the standard connection. Some mesh systems and advanced routers have wireless backhaul features, but these are set up differently and require specific compatible equipment. For a standard modem and router, use the ethernet cable.

What if I have a modem and router in one device?

If your internet service provider gave you a single device that combines modem and router functions, you do not need a separate router. That device handles both jobs. You can still add a separate router if you want better wireless coverage or more control over your network — in that case, connect it to the combined device using an ethernet cable, just as you would with a separate modem.