Netgear routers cannot connect to modems wirelessly — you must use an ethernet cable
A Netgear router cannot receive an internet signal from your modem over the air. Every router, including Netgear models, needs a physical ethernet cable plugged into the modem's ethernet port to get internet access. The wireless part of your router — the part that broadcasts Wi-Fi to your devices — only works after the router itself is connected to the modem by cable.
If you have seen instructions suggesting a wireless connection between modem and router, they are describing something different: connecting your phone or computer to the router's Wi-Fi network after the router is already plugged in. That is wireless. The modem-to-router link must always be wired.
The physical setup takes about two minutes. The configuration takes another five to ten minutes on your first run.
Key Takeaways
- Your Netgear router must connect to the modem using an ethernet cable plugged into the modem's ethernet port and the router's WAN or Internet port.
- The wireless connection you set up is between your devices and the router, not between the router and modem.
- Most Netgear routers detect the modem connection automatically and begin broadcasting Wi-Fi within a few minutes of being powered on.
- If the router does not detect internet, restart both the modem and router, waiting two minutes between each restart.
- You can manage your router's Wi-Fi network name and password through the Netgear Nighthawk app or by visiting 192.168.1.1 in a web browser.
What cable you need and where it plugs in
You need one ethernet cable — the same type used for wired internet anywhere else. Any standard ethernet cable works; the length does not matter as long as it reaches from your modem to your router. Most people use a cable between 3 and 10 feet long.
On the modem side, plug the cable into the port labeled Ethernet, LAN, or sometimes Internet Out. If your modem has multiple ethernet ports, any one of them works. On the Netgear router side, plug the cable into the port labeled WAN, Internet, or Uplink — this is usually a different color from the other ports and is often on the edge of the router. Do not plug it into one of the regular LAN ports.
Once both ends are plugged in, the modem and router should show activity lights. You do not need to do anything else with the cable; it stays connected permanently.
Powering on and waiting for the connection
Turn on your modem first, then turn on your Netgear router. Wait for the modem's lights to stabilize — usually about two minutes. Then wait for the router's lights to stabilize, which typically takes another two to three minutes. During this time, the router is detecting the internet connection from the modem and loading its settings.
When the router is ready, you will see a solid or blinking light on the WAN or Internet port. Some Netgear models also show a light labeled Internet or Online. A solid light means the connection is active. A blinking light means data is moving. Either one is normal.
If you see no light on the WAN port after five minutes, or if the light is red or orange, the connection has not been detected. Move to the troubleshooting section below.
Setting up your Wi-Fi network name and password
Once the router has detected the modem connection, you can set up the wireless network that your devices will connect to. You have two ways to do this: through the Netgear Nighthawk app or through a web browser.
Using the Nighthawk app: read the Netgear Nighthawk app on your phone. Open it and follow the setup wizard. The app will ask you to create a Wi-Fi network name (called an SSID) and a password. Write down both. Once you finish, your phone will automatically connect to the new network, and you can connect other devices from their Wi-Fi settings.
Using a web browser: Open any web browser on a device connected to the router (by ethernet cable or Wi-Fi). Type 192.168.1.1 into the address bar and press Enter. You will be asked to log in. The default username is admin and the default password is password (or sometimes blank). Once logged in, look for a Wi-Fi or Wireless Settings section. Create a network name and password there, then save your changes.
After you save, the router will restart. Wait two minutes, then look for your new network name in your device's Wi-Fi list. Select it and enter the password you created.
What to do if the router does not detect internet
If the WAN port light is off or red after five minutes, or if you can connect to the router's Wi-Fi but have no internet, restart both devices. Unplug the modem, wait 30 seconds, and plug it back in. Wait two minutes for it to fully restart. Then unplug the Netgear router, wait 30 seconds, and plug it back in. Wait another two to three minutes.
Check the WAN port light again. If it is now solid or blinking, the connection has been restored. If it is still off or red, check that the ethernet cable is fully seated in both ports — push it in firmly on each end. If the cable is loose, it will not transmit a signal.
If the light is still not active after restarting and checking the cable, the ethernet cable itself may be damaged. Try a different cable if you have one. If a different cable works, the first cable is faulty and should be replaced.
Connecting devices to your new Wi-Fi network
Once your Wi-Fi network is broadcasting, connecting devices is straightforward. On your phone, tablet, or computer, open the Wi-Fi settings. Look for your network name in the list of available networks. Select it and enter the password you created during setup. The device will connect and should have internet access within a few seconds.
If a device connects but shows no internet, restart that device. If it still has no internet but other devices do, the problem is with that device, not your router. If all devices lose internet at the same time, restart the modem and router again using the process described above.
You can add as many devices as your router supports. Most Netgear routers support 50 to 100 devices at once, though performance may slow if many devices are actively using the network at the same time.
Changing your Wi-Fi password or network name later
If you want to change your network name or password after the initial setup, use the Nighthawk app or return to 192.168.1.1 in your browser. Log in with the same username and password you used before. Find the Wi-Fi or Wireless Settings section and update the name or password. Save your changes and wait for the router to restart.
When you change the password, all your currently connected devices will be disconnected. You will need to reconnect each one using the new password. When you change the network name, devices may take a few minutes to recognize the new name in their Wi-Fi lists.
Frequently Asked Questions
Can I use a wireless bridge to connect my router to the modem instead of a cable?
No. A wireless bridge is a separate device that lets you extend a Wi-Fi network to another location, but it does not replace the modem-to-router cable. Your Netgear router must have a physical ethernet connection to the modem to function as a router. A wireless bridge would require the router to already be connected and working.
What if my modem and router are in different rooms?
Run an ethernet cable between them. Ethernet cables work through walls, under carpet, and along baseboards. They do not interfere with Wi-Fi and can be as long as you need, though cables longer than 100 meters may lose signal strength. If running a cable is not practical, you can place the modem and router in the same location, or use a wireless mesh system instead of a single router.
Do I need to restart my modem and router every time I turn them off?
No. You can turn them off and on normally without restarting. A restart (unplugging for 30 seconds) is only necessary when the connection is not working or when you make changes to the router settings that require a restart.
Why does my router have multiple ethernet ports if only one connects to the modem?
The WAN port connects to the modem. The other ports, labeled LAN, are for devices you want to connect by ethernet cable instead of Wi-Fi — like a desktop computer or a printer. You can use as many LAN ports as you need for wired devices.
Can I use the same ethernet cable for both the modem and router if I unplug and move it?
Technically yes, but it is not practical. You would lose internet every time you moved the cable. It is much simpler to buy a second cable and leave both connections in place permanently.