Connect the router to the modem with one ethernet cable
Your modem receives the internet signal from your provider. Your router takes that signal and broadcasts it wirelessly to your devices. To connect them, you need one ethernet cable — the same kind used for wired internet, with plastic connectors on both ends.
Plug one end of the ethernet cable into the port on the back of your modem labeled "Ethernet," "LAN," or sometimes just a numbered port. Plug the other end into the port on the back of your router labeled "WAN," "Internet," or "Uplink." This is usually a different color from the other ports on the router, often yellow or blue. The cable should click into place.
You do not need to turn anything off first. The modem and router can be powered on during this step.
Key Takeaways
- Use one ethernet cable to connect the modem's LAN port to the router's WAN port — this is the only physical connection you need.
- Wait two to three minutes after plugging in the cable for the modem and router to recognize each other and exchange signals.
- Check the lights on both devices: a steady or blinking light on the modem's internet port and a steady or blinking light on the router's WAN port mean the connection is working.
- If the lights do not appear or stay off, unplug both devices for 30 seconds, plug the modem in first, wait one minute, then plug in the router.
- Once the lights show a connection, you can set up your WiFi network name and password through the router's settings page or app.
Wait for the lights to show the connection is active
After you plug in the cable, both devices need time to recognize each other. Wait two to three minutes before checking anything. During this time, the modem is telling the router "I have internet," and the router is preparing to share it.
Look at the lights on the back or front of both devices. On the modem, find the light for the port you used — it may be labeled "Internet," "Online," or just show a number. On the router, find the light for the WAN port you plugged into. Both lights should be steady on or blinking. A steady light usually means the connection is stable; a blinking light means data is moving through. If either light is off or red, the connection did not work.
The other lights on your modem and router may be off or blinking — that is normal. You are only checking the two ports you connected.
Restart both devices if the lights do not appear
If the lights on the modem's internet port and the router's WAN port are both off or stay red after three minutes, the devices did not recognize the connection. The fastest fix is a restart.
Unplug the power cable from the modem first. Wait 30 seconds. Plug the modem back in and wait one full minute for it to boot up — you will see lights come on and stabilize. Then unplug the router, wait 30 seconds, and plug it back in. Wait another two minutes. Check the lights again.
If the lights still do not show a connection, try a different ethernet cable if you have one. Cables can fail, and a bad cable is the most common reason this step does not work. If a different cable works, the first one is damaged.
Check that the ethernet cable is fully seated in both ports
Ethernet cables should click firmly into their ports. If the connection is loose, the devices will not recognize each other even though the cable looks plugged in.
Unplug the cable from both ends. Look inside each port — they should be clean and free of dust or debris. If you see dust, use a dry cloth or compressed air to clean them gently. Plug the cable back in at the modem end first, pushing until you hear or feel a click. Then plug the other end into the router WAN port and push until it clicks. The small plastic clip on the connector should be fully inside the port.
After reseating the cable, wait two minutes and check the lights again.
Set up your WiFi network name and password once the lights are steady
Once the lights on both the modem's internet port and the router's WAN port are steady or blinking, the devices are talking to each other. You can now set up the WiFi network that your phones, laptops, and tablets will connect to.
Most routers come with a default WiFi name and password printed on a sticker on the back or bottom of the device. You can use these to connect your first device, or you can change them through the router's settings page. To access the settings, open a web browser on a device connected to the router (by WiFi or ethernet) and type the router's IP address — usually 192.168.1.1 or 192.168.0.1 — into the address bar. Log in with the username and password on the sticker, then look for WiFi settings or Network settings to change the name and password.
Some newer routers have a mobile app instead of a web page. Check the sticker or the router's manual to see which method yours uses.
Confirm your internet is working by opening a website
Once your WiFi network is set up, connect a phone, laptop, or tablet to it using the network name and password you created or found on the sticker. Open a web browser and try to load a website like Google.com or your email. If the page loads, your modem and router are connected and working.
If the page does not load, the modem may not have internet from your provider yet. Check with your provider to confirm your service is active. If your service is active, restart the modem again by unplugging it for 30 seconds, then plugging it back in and waiting two minutes.
Frequently Asked Questions
Do I need to use the ethernet cable permanently, or can I unplug it after setup?
Keep the ethernet cable plugged in. The cable is the only way your router receives internet from the modem. Without it, your WiFi will not work. You do not need to unplug it for any reason.
What if my modem and router are in different rooms?
You will need a longer ethernet cable. Standard cables come in lengths from 3 feet to 100 feet. Buy one long enough to reach between the two devices. The length does not affect speed or quality — a 50-foot cable works the same as a 6-foot cable.
Can I use WiFi to connect the modem and router instead of a cable?
No. The modem and router must be connected by ethernet cable. WiFi is what the router broadcasts to your devices after it receives internet from the modem through the cable. The cable is the foundation.
Why is the light on my router's WAN port blinking instead of steady?
A blinking light means data is moving through the port — this is normal and means the connection is working. A steady light means the connection is stable but no data is moving at that moment. Both steady and blinking are good signs.
What if I plugged the cable into the wrong port on the router?
If you plugged it into one of the numbered LAN ports instead of the WAN port, the router will not receive internet. Unplug the cable and move it to the WAN port — it is usually a different color and labeled clearly. The other ports are for devices you want to connect by ethernet, not for the modem.