Connect the Router to Your Modem in Three Steps
Your Xfinity router connects to your modem with a single ethernet cable, then broadcasts wifi to your devices. The physical connection takes less than a minute: plug one end of an ethernet cable into the yellow port on the back of your modem, plug the other end into the internet port (usually labeled WAN or Internet) on the back of your router, then power on the router. Wait two to three minutes for the lights to stabilize — you will see a solid white or blue light on the front when it is ready.
The router's lights tell you what is happening. A blinking light means it is starting up or connecting to the modem. A solid light means the connection is active. If the light stays red or off after five minutes, unplug the router for 30 seconds, plug it back in, and wait again. If it still does not light up, the ethernet cable may be loose — unplug both ends and push them firmly back in until you hear a click.
Do not plug the router into the same power outlet as the modem if you can avoid it. If your power goes out, both devices will restart at the same time, which can cause connection delays. Using separate outlets means one can stay on if the other loses power briefly.
Key Takeaways
- Connect the modem to the router using an ethernet cable plugged into the yellow port on the modem and the WAN or Internet port on the router.
- Power on the router and wait two to three minutes for the lights to show a solid color, which means the connection is active.
- If the light does not turn solid after five minutes, unplug the router for 30 seconds and plug it back in.
- Use separate power outlets for the modem and router so one device can stay on if the other loses power.
- Once the router is connected to the modem, you can then connect your devices to the router's wifi network using the network name and password printed on the router label.
Find Your Wifi Network Name and Password
Your Xfinity router broadcasts a wifi network with a name and password printed on a sticker attached to the router itself. Look on the back or bottom of the device for a label that shows "Network Name" (also called SSID) and "Network Password" or "Passphrase." The network name often starts with "XFINITY" or "xfinitywifi" followed by numbers or letters. Write down both the name and password before you start connecting devices — you will need them for each phone, laptop, or tablet you want to use.
If you cannot find the sticker or the label is worn away, you can log into the router's settings page to see the network name and password. Open a web browser on a computer connected to the router with an ethernet cable, type 192.168.0.1 into the address bar, and press Enter. Log in with the username admin and the password printed on your modem's label (not the router). Once you are logged in, look for a section labeled "Wifi" or "Wireless" to find your network name and password.
Connect Your Devices to the Wifi Network
On your phone, tablet, or laptop, open the wifi settings and look for your network name in the list of available networks. Tap or click on it, then enter the password exactly as it appears on the router label — passwords are case-sensitive, so uppercase and lowercase letters matter. If you type the password wrong, the device will not connect and will ask you to try again.
Once a device connects, it will remember that network and connect automatically the next time it is in range. If a device keeps disconnecting or connecting slowly, move it closer to the router. Walls, metal objects, and other electronics can weaken the wifi signal. If the problem continues, restart the device by turning it off for 10 seconds and turning it back on.
If you want to change the network name or password to something easier to remember, log into the router settings page at 192.168.0.1 and look for the Wifi or Wireless section. You can create a custom name and password there, but write down the new password somewhere safe — you will need it to connect future devices.
Understand the Lights on Your Router
The front of your Xfinity router has several lights that show you what is happening. A solid white or blue light on the power button means the router is on and working. A blinking light means data is moving between your devices and the internet. A red light or no light at all means something is wrong — usually a loose cable or a power problem.
The wifi light (often labeled with a wifi symbol) should be solid or blinking when the router is broadcasting your network. If this light is off, wifi is disabled. Press and hold the wifi button on the back of the router for three seconds to turn it back on. The internet light should be solid when the router is connected to the modem. If this light is off or red, check that the ethernet cable is plugged firmly into both the modem and the router.
If all the lights are off, make sure the power cable is plugged into both the router and a working outlet. Try plugging a lamp into the same outlet to confirm the outlet has power. If the outlet works but the router still will not turn on, the power adapter may be broken — contact Xfinity support for a replacement.
Restart Your Router When Connection Problems Happen
Restarting the router fixes most connection problems. Unplug the power cable from the back of the router, wait 30 seconds, then plug it back in. The lights will blink as the router restarts — this usually takes two to three minutes. Do not unplug the modem at the same time unless you are restarting both devices on purpose.
If restarting does not fix the problem, check that the ethernet cable between the modem and router is plugged in firmly on both ends. A loose cable is the most common reason a router loses internet connection. If the cable is tight and the problem continues, try using a different ethernet cable — the original cable may be damaged.
If your internet is slow even though the lights show a good connection, restart both the modem and router together. Unplug the modem first, wait 30 seconds, then unplug the router. Wait another 30 seconds, then plug the modem back in and wait for its lights to stabilize. Finally, plug the router back in and wait for its lights to stabilize. This full restart can take five to ten minutes but often improves speed.
Move Your Router to a Better Location
The location of your router affects how strong your wifi signal is throughout your home. Place the router in a central, elevated location — a shelf or wall mount in the middle of your home works better than a corner or closet. Avoid placing it on the floor, inside a cabinet, or behind a door, as these locations block the signal.
Keep the router away from metal objects, microwaves, cordless phones, and baby monitors, which can interfere with the wifi signal. If your router is next to your modem, that is fine — they can sit side by side. However, if your modem is in a basement or far corner of your home, consider moving the router to a more central spot and running a longer ethernet cable between them.
If you have a large home or thick walls, one router may not reach every room. You can add a wifi extender or mesh wifi system to expand coverage, but that is a separate purchase and setup. For now, moving your current router to a central location will improve the signal in most rooms.
Frequently Asked Questions
What if the router does not get an internet light after I plug it in?
Check that the ethernet cable is plugged into the yellow port on the modem and the WAN or Internet port on the router. Both connections must be tight — unplug and replug each end. If the light still does not appear after two minutes, the cable may be damaged. Try a different ethernet cable.
Can I use wifi and ethernet at the same time?
Yes. You can connect some devices to wifi and others to the router using ethernet cables plugged into the numbered ports on the back. Ethernet connections are usually faster and more stable than wifi, so use ethernet for devices that need high speed, like gaming consoles or desktop computers.
How do I reset the router to factory settings?
Press and hold the reset button on the back of the router for 10 to 15 seconds using a paperclip or pen. The router will restart and erase all custom settings, including any password you created. It will return to the default network name and password printed on the label. You will need to set it up again from the beginning.
Why does my wifi keep disconnecting?
Restart the router by unplugging it for 30 seconds and plugging it back in. If disconnections continue, move closer to the router to rule out signal problems. Check that the ethernet cable between the modem and router is tight. If the problem persists, restart the modem as well by unplugging it for 30 seconds.
Can I move the router to a different room?
Yes, as long as you can run an ethernet cable from the modem to the router. The cable can run along walls or under carpet (though under carpet is not ideal). A longer ethernet cable will not slow down your connection — the distance does not matter as long as the cable is plugged in firmly on both ends.