The Basic Setup: Router One Plugs Into the Modem, Router Two Plugs Into Router One

To connect two routers to a single modem, you run an ethernet cable from the modem to the first router's WAN (internet) port, then run a second ethernet cable from the first router's LAN port to the second router's WAN port. The modem supplies internet to the first router, which then shares that connection to the second router. Both routers broadcast their own wireless networks, so your devices can connect to either one.

This setup works because routers are designed to pass internet traffic downstream. The first router handles the connection to your modem and acts as the gateway for your network. The second router receives internet from the first and extends coverage or adds capacity without needing a second modem or a second internet account.

The physical order matters: modem → router one → router two. If you reverse it or try to connect both routers directly to the modem, one of them will not receive internet properly.

Key Takeaways

  • Connect an ethernet cable from your modem's output port to the WAN port on your first router, then connect a second ethernet cable from that router's LAN port to the second router's WAN port.
  • The first router must be set to gateway mode (the default), while the second router should be set to bridge or access point mode so it does not try to manage the network.
  • Both routers can broadcast separate wireless networks with different names and passwords, or you can give them the same name so devices switch between them automatically.
  • You will need to log into each router's settings separately to configure its wireless network name, password, and mode.

Configuring the First Router as Your Gateway

The first router — the one plugged directly into the modem — should remain in its default gateway mode. This is usually the factory setting, so you may not need to change anything. The gateway router manages the connection to your modem and assigns IP addresses to all devices on your network.

Log into the first router's settings by opening a web browser and typing its IP address (usually 192.168.1.1 or 192.168.0.1 — check the router's label or manual). Enter the admin username and password, which are often printed on the device itself. Once inside, look for wireless settings and change the network name (SSID) and password to something you will recognize. Write these down.

Leave all other settings at their defaults unless you have a specific reason to change them. The gateway router handles all the heavy lifting of connecting to your modem and managing traffic, so a standard configuration works fine for most homes.

Setting the Second Router to Bridge or Access Point Mode

The second router must be told not to act as a gateway. If you leave it in gateway mode, it will try to create its own separate network and may conflict with the first router. Instead, set it to bridge mode or access point mode — different routers use different names for the same function.

Log into the second router using the same method: type its IP address into a browser. The default is often 192.168.1.1, but if that does not work, try 192.168.0.1 or check the router's manual. Once logged in, look for a settings menu labeled "Operating Mode," "Router Mode," "Network Mode," or "Advanced Settings." Select bridge mode or access point mode from the options.

After switching modes, the second router will restart. It may take a minute or two to come back online. Once it does, log back in and set up a wireless network name and password. You can use the same name and password as the first router (so devices connect seamlessly) or different ones (so you can see which router a device is connected to).

Choosing Between One Network Name or Two

If you give both routers the same wireless network name and password, your devices will automatically switch between them as you move around your home. This is called roaming, and it works smoothly on most phones and laptops. You will not see two networks listed — just one.

If you give them different names, you will see both networks in your device's list of available networks. You can connect to whichever one has the stronger signal in your location. This approach is useful if you want to test which router performs better in different rooms, or if you want to keep certain devices on one router and others on the second.

For most homes, using the same name and password is simpler. Your devices handle the switching automatically, and you do not have to think about which router you are using.

Checking Your Connection and Troubleshooting

Once both routers are set up, open a web browser on a device connected to the second router and visit a speed-test site or try loading a webpage. If the page loads, both routers are working and passing internet traffic correctly. If the second router has no internet, the most common causes are a loose ethernet cable, the second router still in gateway mode, or the cable plugged into the wrong port.

Check that the ethernet cable between the two routers is firmly seated in the LAN port of the first router and the WAN port of the second. If it is loose, push it in until you hear a click. Then restart the second router by unplugging it for 10 seconds and plugging it back in.

If the second router still has no internet after a restart, log back into its settings and confirm it is in bridge or access point mode, not gateway mode. Some routers default to gateway mode even after a factory reset, so this is worth double-checking.

Using Ethernet Cables vs. Wireless Backhaul

The setup described above uses an ethernet cable to connect the two routers. This is the most reliable method because ethernet is faster and more stable than wireless. If you cannot run a cable between the routers, some routers support wireless backhaul, which means the second router connects to the first one over WiFi instead of ethernet.

Wireless backhaul is slower than a wired connection because the second router has to receive and transmit data on the same frequency. You will see a noticeable drop in speed compared to a wired setup. If you have the option to run an ethernet cable — even a long one along a wall or through a basement — that is the better choice.

To set up wireless backhaul, put the second router in access point mode and it will search for nearby networks. Select the first router's network name and enter its password. The second router will then connect wirelessly and extend your network. The process varies by router brand, so check the manual if the option does not appear in the settings menu.

When Two Routers Make Sense and When They Do Not

Two routers are useful if your home is large, your modem is in a corner, or you have dead zones where WiFi does not reach. A second router in a different part of your home can cover those areas. Two routers also add capacity if you have many devices connecting at once — each router handles its own traffic, so neither one gets overwhelmed.

Two routers are not necessary if your single router already covers your entire home with strong signal. Adding a second router will not speed up your internet; it will only extend coverage. If your internet is slow, the problem is usually your internet service plan or your modem, not your router. A second router will not fix that.

If you need better coverage, a mesh WiFi system (which uses multiple units designed to work together) is often easier to set up than two separate routers. Mesh systems handle the mode switching and network configuration automatically. However, if you already own two routers, connecting them this way costs nothing and works well.

Frequently Asked Questions

Can I plug both routers directly into the modem?

No. A modem has only one output port, and even if it had two, both routers would try to act as gateways and conflict with each other. One router must plug into the modem, and the second must plug into the first router.

Do I need a second modem to use two routers?

No. One modem supplies internet to both routers. The first router receives the connection from the modem and passes it to the second router. You only need a second modem if you want two separate internet accounts.

Will two routers slow down my internet?

A wired connection between the routers will not slow your internet noticeably. A wireless connection (backhaul) will reduce speed on the second router by roughly half, since it has to send and receive on the same frequency. Your main internet speed is determined by your service plan and modem, not by the routers.

What if my second router does not have a WAN port?

Some routers have only LAN ports and are designed to work as access points only. If your second router has no WAN port, plug the ethernet cable into any LAN port and set the router to access point mode. It will work the same way.

Can I use WiFi instead of an ethernet cable to connect the routers?

Yes, if your routers support wireless backhaul. The second router will connect to the first over WiFi, but you will lose speed compared to a wired connection. An ethernet cable is faster and more reliable if you can run one.