What You Need Before You Start

A Comcast modem connects your home to the internet through a coaxial cable (the thick cable with a metal connector) that runs from the wall outlet to the modem's input port. You'll also need an ethernet cable to connect the modem to your router, or directly to a computer if you're testing the connection. Most Comcast modems come with one ethernet cable in the box.

Check that you have an active Comcast internet service account before you begin. If you're setting up service for the first time, Comcast will have assigned a service address and set up date. If you're replacing an old modem, your account is already active and ready to use.

Gather these items: your Comcast modem, the coaxial cable (usually included), an ethernet cable, and a power adapter. Place the modem in a central location in your home — near where the coaxial cable enters from outside works best, though any spot with good airflow will do. Avoid enclosed cabinets or closets, as modems generate heat and need ventilation.

Key Takeaways

  • The coaxial cable from the wall outlet connects to the port labeled "Cable In" on the back of the modem.
  • An ethernet cable runs from the modem's ethernet port to your router or computer to carry the internet signal into your devices.
  • The modem lights will show you whether it has connected to Comcast's network — typically a solid green light means you're online.
  • set up usually takes 5 to 15 minutes after you plug in the modem, but can take up to an hour on first setup.
  • If the lights don't show a connection after 20 minutes, restart the modem by unplugging it for 30 seconds, then plug it back in.

Connecting the Coaxial Cable

Locate the coaxial cable outlet on your wall. It looks like a small metal jack with a threaded ring around it. Unscrew any cap covering it. Take the coaxial cable and screw it firmly into the wall outlet by hand — you should feel it tighten, but do not force it or use pliers, as that can damage the connector.

Now locate the port on the back of your modem labeled "Cable In" or sometimes just "In". It will be the largest port on the back panel. Screw the other end of the coaxial cable into this port the same way — hand-tight, firm but not forced. The cable should not wiggle once connected.

If you do not see a coaxial outlet on your wall, or if the outlet is in an inconvenient location, contact Comcast to discuss running a new line. Do not attempt to run coaxial cable yourself through walls or ceilings, as improper installation can degrade your signal.

Connecting the Ethernet Cable

Look at the back of the modem and find the ethernet ports. Most Comcast modems have one or two ports labeled with numbers (like "1" or "2") or the word "Ethernet". These ports are smaller than the coaxial port and look like phone jacks with eight small pins inside.

If you're connecting to a router, plug one end of the ethernet cable into any available ethernet port on the modem, then plug the other end into the port on your router labeled "Internet", "WAN", or "Uplink". If you're connecting directly to a computer for testing, plug the ethernet cable into the modem and into your computer's ethernet port instead.

The ethernet cable is not directional — either end can go into either device. If the cable does not fit, do not force it. Ethernet connectors have a small clip that should click into place when fully inserted.

Powering On the Modem

Plug the modem's power adapter into the back of the unit where it says "Power" or shows a power symbol. Then plug the adapter into a wall outlet or power strip. The modem will begin to boot up when ready.

Watch the lights on the front of the modem. Within 10 to 15 seconds, you should see lights begin to turn on. Most Comcast modems show a power light first, then lights for "Online", "Downstream", "Upstream", and "WiFi" (if your modem has built-in WiFi). Do not unplug the modem during this startup process.

The modem is communicating with Comcast's network during startup. This process is called provisioning. You will see the lights change colors and patterns as the modem searches for the network, authenticates your account, and downloads its configuration. This is normal and expected.

Waiting for the Online Light

The most important light is labeled "Online", "Internet", or sometimes just shows a globe symbol. This light should turn solid green within 5 to 15 minutes of powering on the modem. Once it is solid green, your modem has successfully connected to Comcast's network and your internet is ready to use.

If you see a solid green online light, your connection is working. Open a web browser on your computer or router and try to load a website. If the page loads, your setup is complete.

If the online light is off, blinking red, or amber after 20 minutes, the modem has not yet connected. This can happen on first set up or if there is a service issue. Wait another 10 minutes — some modems take up to 30 minutes on initial setup. If the light is still not green after 30 minutes, move to the troubleshooting section below.

Restarting the Modem If It Is Not Connecting

If the online light has not turned green after 30 minutes, restart the modem. Unplug the power adapter from the wall outlet and wait 30 seconds. Count to 30 out loud or use a timer — this gives the modem time to fully power down. Then plug the power adapter back in.

Watch the lights again as the modem boots up. The startup sequence should take 5 to 15 minutes. If the online light turns green this time, your connection is working and the restart solved the problem.

If the online light still does not turn green after a second restart, check that the coaxial cable is screwed firmly into both the wall outlet and the modem. A loose connection is the most common reason a modem will not connect. Unscrew the cable from the modem, inspect the connector for dirt or damage, and screw it back in firmly.

When to Contact Comcast Support

If you have restarted the modem twice, checked that both cables are firmly connected, and the online light is still not green after 45 minutes, contact Comcast. You can reach them by phone at 1-800-COMCAST (1-800-266-2278) or through their website. Have your account number and service address ready.

Comcast support can check whether your service is active, whether there is an outage in your area, and whether your modem has been registered to your account. They may also walk you through additional troubleshooting steps or send a technician if there is a problem with the line coming into your home.

If you are setting up service for the first time, Comcast may need to set up your modem remotely before it will connect. This usually happens automatically, but if you are still waiting for set up after 24 hours, call support to confirm your service is active.

Frequently Asked Questions

Do I need a router if I have a Comcast modem?

Not necessarily. If your modem has built-in WiFi (many newer Comcast modems do), you can connect wirelessly without a separate router. However, a separate router often provides better WiFi range and performance. You can use both together — the modem connects to the internet, and the router broadcasts the WiFi signal throughout your home.

What do the different colored lights mean?

A solid green light means the modem is working normally. A blinking green light usually means the modem is sending or receiving data. A red or amber light means there is a problem — either the modem is still starting up, or it has not connected to the network. If a light stays red for more than 30 minutes, restart the modem or contact Comcast.

Can I move the modem to a different room after it is connected?

Yes, but you will need to move the coaxial cable with it. The coaxial cable must run from the wall outlet to the modem, so the modem can only be as far from the outlet as your cable will reach. If you want to move the modem far from the outlet, you may need a longer coaxial cable, which Comcast can provide.

What if the coaxial cable from the wall is already connected to something else?

If the cable is connected to a cable box or TV, you will need a splitter. A coaxial splitter allows one cable from the wall to feed both the modem and another device. You can buy a splitter at any electronics store for under $20. Screw the wall cable into the splitter, then run separate cables from the splitter to the modem and to your other device.

How long does it take for the modem to fully set up?

On a replacement modem with an active account, set up usually takes 5 to 15 minutes. On a first-time setup, it can take up to an hour. If your modem has not connected after an hour, contact Comcast to confirm your service is active and your modem has been registered to your account.