Connect the cables in the right order
Your Xfinity router connects to your modem with an ethernet cable, then to power. The order matters because starting with power can cause connection errors that take time to clear.
First, take an ethernet cable (the one with rectangular connectors on both ends) and plug one end into the yellow port on the back of your modem. Plug the other end into the port on your router labeled Internet, WAN, or Modem — the label depends on your router model, but it is usually separate from the other ports and often a different color. Do not plug into the regular ethernet ports yet; those are for devices in your home.
Once the ethernet cable is seated firmly in both ports, plug the router's power cable into the back of the unit and into a wall outlet or power strip. The router will take 2 to 3 minutes to start up. You will see lights on the front begin to turn on and change color as it boots.
Key Takeaways
- Connect the ethernet cable from your modem's yellow port to your router's Internet or WAN port before plugging in power.
- Wait 2 to 3 minutes after powering on for the router to fully boot and connect to your modem.
- Look for a solid light on the Internet or WAN port to confirm the modem and router are talking to each other.
- The router's default network name and password are printed on a sticker on the back or bottom of the unit.
- If lights do not appear or the Internet light stays off after 5 minutes, unplug the router for 30 seconds and plug it back in.
Wait for the lights to show a stable connection
While the router is booting, watch the lights on the front. You should see them light up in sequence — usually power first, then internet, then wifi. This takes about 2 to 3 minutes total.
The light you care about most is the one labeled Internet, WAN, or Online. Once it turns solid (not blinking), your router and modem are connected and talking. If that light stays off or red after 5 minutes, the ethernet cable may not be fully seated. Unplug the router, wait 30 seconds, and plug it back in. If the light still does not appear, try a different ethernet cable — the first one may be damaged.
Find your network name and password
Once the Internet light is solid, your router is broadcasting a wifi network. You will find the network name (also called SSID) and password on a sticker attached to the back or bottom of the router. The sticker usually shows both pieces of information clearly labeled.
Write down or take a photo of this information before you move the router, because you will need it to connect your phone, laptop, or other devices. Some Xfinity routers also print this information on a card that comes in the box.
Connect your first device to test the network
On your phone or laptop, open the wifi settings and look for the network name from the sticker. Select it and enter the password exactly as it appears — passwords are case-sensitive, so capital letters matter.
Once you are connected, open a web browser and go to any website, like google.com. If the page loads, your router is working. If you see an error or the page does not load, wait another minute and try again — the router may still be finishing its startup.
Position the router for the best signal
Place your router in a central, elevated location in your home — a shelf or wall mount works better than the floor or inside a cabinet. Avoid putting it next to a microwave, cordless phone, or other electronics that can interfere with the signal. Walls and metal objects also weaken the signal, so keep the router away from those if you can.
If you have a two-story home, placing the router on the upper floor usually covers both levels better than placing it in the basement. You may need to experiment with location to find the spot where you get the strongest signal in the rooms you use most.
Log in to the router settings if you need to change the password
The default password on the sticker is find, but you can change it to something easier to remember. Open a web browser and go to 192.168.0.1 or 192.168.100.1 (try the first one first). You will see a login page.
Enter admin as the username and the password from the sticker as the password. Once you are logged in, look for a section called Wifi, Wireless, or Network Settings. From there you can change the network name and password to anything you want. Write down your new password and save the changes before you close the browser.
Troubleshoot if the router does not connect to the modem
If the Internet light stays off or red after 5 minutes, start with the simplest fix: unplug the router for 30 seconds, then plug it back in. This clears any temporary errors and lets both devices restart fresh.
If that does not work, check that the ethernet cable is fully pushed into both the modem and the router — a cable that looks connected but is not fully seated is the most common cause. Try unplugging the cable from both ends, waiting 10 seconds, and plugging it back in firmly. If you still see no Internet light after another 2 minutes, the cable itself may be bad. Swap it for a different ethernet cable if you have one available.
If the Internet light comes on but you cannot connect to the wifi network, restart the modem by unplugging it for 30 seconds, then plug it back in. Wait for the modem's lights to stabilize (usually 1 to 2 minutes), then check the router's wifi network again.
Frequently Asked Questions
Do I need to call Xfinity to set up the router?
No. Once the ethernet cable is connected and the Internet light is solid, the router is active and ready to use. Xfinity routers that come with your service are pre-configured to work with your modem automatically. You do not need to contact Xfinity unless the Internet light does not appear after 5 minutes.
Can I use my own ethernet cable or does it have to be the one that came in the box?
Any standard ethernet cable works. The cable in the box is just a convenience. If you need a longer cable to reach your modem, any Cat5e, Cat6, or Cat6a cable from any brand will work the same way.
What if I see lights on the router but no wifi network appears?
Wait another minute — the router may still be booting. If the wifi network still does not show up after 3 minutes total, check that the Internet light is solid, not blinking or off. If it is off, the modem connection is not complete. If it is solid but you still see no wifi, restart the router by unplugging it for 30 seconds.
Can I move the router to a different room after it is set up?
Yes. You can unplug the router and move it anywhere in your home as long as the ethernet cable can still reach your modem. If the cable is not long enough, you can buy a longer ethernet cable. Just plug it in and the router will reconnect automatically within a minute or two.
Is the password on the sticker permanent or can I change it?
You can change it anytime by logging into the router settings at 192.168.0.1 or 192.168.100.1 with the username admin and the password from the sticker. Your new password will take effect when ready, and all devices will need to reconnect using the new password.