Connect Your Modem to Power and the Wall Jack

Start by placing your Xfinity modem in a central location in your home, away from metal objects, microwaves, and cordless phones. These can interfere with your signal. Leave at least a few inches of space on all sides so air can circulate around it.

Plug the power cable into the back of the modem, then into a wall outlet or power strip. The modem will take 2 to 3 minutes to power on. You'll see lights begin to flash on the front panel—this is normal. Do not unplug it during this startup period.

While the modem is powering up, locate the coaxial cable (the thick cable with a threaded connector) that runs from your wall jack to where you want to place the modem. Screw this cable firmly into the port labeled "Cable In" on the back of the modem. Hand-tighten only—do not use a wrench, as this can damage the connection.

Key Takeaways

  • Place your modem in a central location away from metal objects and interference sources, then plug it into power and wait 2 to 3 minutes for startup.
  • Connect the coaxial cable from your wall jack to the "Cable In" port on the back of the modem by hand-tightening only.
  • Wait for the lights to stabilize—the "Online" or "Internet" light should turn solid green or white within 5 to 10 minutes of connecting the cable.
  • Connect your devices to the modem's Wi-Fi network using the network name and password printed on the modem's label, or use an ethernet cable for a wired connection.
  • If the online light does not turn solid after 15 minutes, restart the modem by unplugging it for 30 seconds, then plugging it back in.

Wait for the Lights to Stabilize

After you connect the coaxial cable, the modem will begin searching for a signal from Xfinity. Watch the lights on the front panel. You should see the "Online," "Internet," or "Downstream" light turn solid green or white within 5 to 10 minutes. This means the modem has locked onto the network and is ready to use.

During this time, other lights may flash or stay on. The "Power" light should be solid. The "Downstream" and "Upstream" lights may blink as the modem communicates with Xfinity's network. This is expected. Do not move or unplug the modem while the lights are stabilizing.

If the online light does not turn solid after 15 minutes, the modem may not be receiving a signal. Check that the coaxial cable is screwed in tightly at both the wall jack and the modem. If it is loose, tighten it by hand and wait another 5 minutes.

Connect Your Devices Using Wi-Fi

Once the online light is solid, your modem is broadcasting a Wi-Fi signal. Look at the label on the bottom or back of the modem. You will see a network name (also called SSID) and a password. These are unique to your modem.

On your phone, tablet, or computer, open the Wi-Fi settings and look for the network name from your modem's label. Select it and enter the password exactly as it appears on the label—passwords are case-sensitive, so uppercase and lowercase letters matter. After you enter the password, your device will connect to the internet.

If you have multiple devices, you can connect them all to the same network using the same password. Each device will remember the password after the first time you enter it, so you won't have to type it again.

Use an Ethernet Cable for a Wired Connection

If you want a faster, more stable connection for a computer, gaming console, or streaming device, you can use an ethernet cable instead of Wi-Fi. Plug one end of an ethernet cable into one of the ports labeled "Ethernet" on the back of the modem. Plug the other end into the ethernet port on your device.

The connection is automatic—your device will recognize the wired network when ready and begin using it. Wired connections are generally faster and more reliable than Wi-Fi, especially if you are far from the modem or in a building with thick walls.

You can use both Wi-Fi and ethernet at the same time. Some devices can connect via Wi-Fi while others use ethernet. The modem supports this without any extra setup.

Restart Your Modem if It Is Not Working

If your modem is not connecting to the internet, or if your internet suddenly stops working, a restart often fixes the problem. Unplug the power cable from the back of the modem. Wait 30 seconds—count them out or set a timer. This gives the modem time to fully shut down.

Plug the power cable back in. The modem will go through its startup sequence again. The lights will flash, and within 2 to 3 minutes you should see the online light turn solid again. This usually takes less time than the first startup because the modem remembers your network settings.

If restarting does not fix the problem, check that the coaxial cable is still screwed in tightly. A loose cable is the most common reason for lost connection. If the cable is tight and the online light still will not turn solid after 15 minutes, your service may be down in your area. You can check Xfinity's website or call their support line to confirm.

Understand the Lights on Your Modem

Your Xfinity modem has several lights that tell you what is happening. The Power light should always be solid when the modem is plugged in. The Online or Internet light is the most important—it should be solid green or white when you are connected. If it is off or red, you do not have internet.

The Downstream and Upstream lights show data moving to and from Xfinity's network. These may blink during normal use. The Wi-Fi light indicates that your wireless network is active. If you turn off Wi-Fi in your modem's settings, this light will turn off, but your ethernet connections will still work.

If the online light is off or red, and restarting does not fix it, the problem is usually a loose coaxial cable or an outage in your area. Tighten the cable first, wait 5 minutes, and check the light again.

Frequently Asked Questions

How long does it take for the modem to connect after I plug it in?

The modem takes 2 to 3 minutes to power on completely. After you connect the coaxial cable, it usually takes another 5 to 10 minutes for the online light to turn solid. If it takes longer than 15 minutes, restart the modem by unplugging it for 30 seconds.

Can I move my modem to a different room?

Yes, but keep it in a central location for the best Wi-Fi coverage. The coaxial cable from your wall jack must reach the modem, so you are limited by where the wall jacks are in your home. If you need to move it far from the nearest jack, you may need a longer coaxial cable.

What if I forgot the Wi-Fi password?

The password is printed on the label attached to the bottom or back of your modem. If you cannot find the label, you can reset the modem to its factory settings by holding the reset button on the back for 10 seconds. This will erase your settings, and you will need to set up the modem again from the beginning.

Do I need to do anything else after the modem connects?

No. Once the online light is solid and your devices are connected, your modem is ready to use. You do not need to install software or create an account. If you want to change your Wi-Fi password or adjust other settings, you can log into your modem's admin panel through a web browser, but this is optional.

What should I do if the online light turns off after it was working?

First, check that the coaxial cable is screwed in tightly at both ends. If it is loose, tighten it and wait 5 minutes. If the light still does not come back on, restart the modem by unplugging it for 30 seconds. If the problem continues, there may be an outage in your area—check Xfinity's website or call their support line.