Connect the router to your modem with an ethernet cable

Your Xfinity router connects to your modem using a single ethernet cable. One end plugs into the yellow port on the back of your modem (labeled "Ethernet" or "LAN"). The other end plugs into the port on the back of your router labeled "Internet," "WAN," or "Modem" — the label depends on which Xfinity model you have.

Make sure both devices are powered off before you plug in the cable. Once the cable is seated firmly in both ports, power on your modem first and wait 2 to 3 minutes for it to fully boot. Then power on your router and wait another 2 to 3 minutes. You should see lights on the front of both devices — a solid light on the modem means it has connected to Xfinity's network, and lights on the router mean it is communicating with the modem.

If you are replacing an old router, unplug the ethernet cable from the old one before connecting the new one. Leaving both plugged in can confuse your modem and prevent either router from working.

Key Takeaways

  • The ethernet cable runs from the yellow port on your modem to the Internet or WAN port on your router.
  • Power on the modem first and wait a few minutes, then power on the router — do not power them on at the same time.
  • Solid lights on both devices mean they are connected; if lights are off or blinking red, restart both devices by unplugging them for 30 seconds.
  • Your router will broadcast a Wi-Fi network name (SSID) and password, usually printed on a sticker on the router itself or in the setup paperwork.
  • If your router does not show lights or broadcast Wi-Fi after 5 minutes, the ethernet cable may not be fully inserted or your modem may not be online.

Check that your modem is online before connecting the router

Your router cannot work if your modem is not connected to Xfinity's network. Before you plug in the ethernet cable, look at the lights on the front of your modem. You should see a solid green or white light labeled "Online," "Internet," or "Downstream." If that light is off, blinking, or red, your modem is not ready yet.

If the modem light is not solid, unplug the modem's power cable, wait 30 seconds, and plug it back in. Wait another 3 to 5 minutes for it to boot. During this time, you may see the light blink or change color — that is normal. Once you see a solid light, the modem is online and you can connect the router.

If the light stays off or red after 10 minutes, check that the coaxial cable (the thick cable with a threaded connector) is screwed firmly into the port labeled "Cable In" on the back of the modem. If it is loose, tighten it by hand and wait another 2 minutes. If the light still does not come on, your modem may need service from Xfinity.

Locate the Wi-Fi network name and password on your router

Once your router is powered on and showing lights, it will broadcast a Wi-Fi network. The network name (called the SSID) and the password are printed on a sticker on the bottom or back of your router. They may also be in the setup guide or on a card that came in the box.

The sticker usually shows two networks: one labeled with "2.4GHz" and one labeled "5GHz." Both use the same password. The 5GHz network is faster but has shorter range; the 2.4GHz network is slower but reaches farther. Most phones and devices will automatically show both options when you search for Wi-Fi networks.

If you cannot find the sticker or the setup paperwork, you can log into your router's settings page. Open a web browser on a device that is already connected to Wi-Fi, go to 192.168.0.1 or 192.168.100.1, and log in with the username admin and the password printed on your modem (not your router). From there you can see or change your Wi-Fi network name and password.

Restart your router if it is not showing lights or Wi-Fi

If your router is plugged in but the lights are off, or if you cannot find the Wi-Fi network after 5 minutes, restart both devices. Unplug the power cable from the back of your router and wait 30 seconds. While you wait, also unplug your modem's power cable. After 30 seconds, plug the modem back in first and wait 2 to 3 minutes for it to boot. Then plug the router back in and wait another 2 to 3 minutes.

During the restart, watch the lights on both devices. The modem should show a solid light within 3 minutes. The router should show at least one light (usually labeled "Power" or "Status") within 2 minutes of being plugged in. If the router still shows no lights after 5 minutes, the power cable may not be fully inserted into the wall outlet or the router itself may be faulty.

If lights come on but you still cannot see the Wi-Fi network, check that the ethernet cable is firmly seated in both the modem's yellow port and the router's Internet port. A loose cable is the most common reason a router powers on but does not connect to the modem.

Understand the lights on your router

Most Xfinity routers have four or five lights on the front. A Power light (usually white or blue) means the router is plugged in and turned on. An Internet light (usually white or blue) means the router is connected to your modem. A Wi-Fi light (usually white or blue) means the router is broadcasting a wireless network. A Devices light (usually white or blue) means at least one device is connected to the Wi-Fi.

Solid lights mean everything is working. Blinking lights usually mean the router is busy (uploading a software update, for example) and will settle down in a minute or two. Red or orange lights mean there is a problem — most often a loose ethernet cable or a modem that is not online.

If the Internet light is off or red, unplug the ethernet cable from both the modem and the router, wait 10 seconds, and plug it back in firmly. If the light stays red after 2 minutes, restart both devices as described above.

Set up Wi-Fi on your devices

Once your router is showing lights and broadcasting Wi-Fi, you can connect your phone, laptop, or tablet. On your device, open the Wi-Fi settings and look for the network name printed on your router's sticker. Tap or click on it, enter the password (also from the sticker), and wait a few seconds. You should see a checkmark or "Connected" next to the network name.

If your device does not see the network after 5 minutes, restart your router by unplugging it for 30 seconds. If the network appears but you cannot connect, double-check that you are typing the password correctly — it is case-sensitive, which means capital letters matter. If you keep getting the password wrong, you can reset the router to its factory settings by holding down the reset button (a small hole on the back) for 10 seconds, but this will erase any changes you made and restore the default network name and password from the sticker.

If you can connect to Wi-Fi but have no internet, the problem is usually with your modem, not your router. Check that the modem's Online light is solid, and if it is not, restart the modem as described above.

Frequently Asked Questions

Do I need to call Xfinity to set up my router?

No. Your router does not need to be registered or activated with Xfinity. Once it is connected to your modem with an ethernet cable and powered on, it will work when ready. You may see a setup wizard or welcome screen when you first connect a device to the Wi-Fi, but you can skip it — the router is already working.

Can I use a router that is not made by Xfinity?

Yes. Any router will work with an Xfinity modem as long as you connect them with an ethernet cable. You do not need to buy an Xfinity-branded router. Third-party routers often cost less and may have features Xfinity routers do not have, but they are not required.

What if the ethernet cable is too short to reach from my modem to where I want the router?

You can buy a longer ethernet cable at any electronics store or online. Look for a Cat5e or Cat6 cable in the length you need — 25 feet, 50 feet, or longer. The longer the cable, the less it costs per foot. A longer cable will not slow down your internet.

Can I move my router to a different room after I set it up?

Yes, but you will need a longer ethernet cable to reach from your modem to the new location. You cannot move the router more than a few feet away from the modem without a longer cable. If you want to place the router in a central location in your home for better Wi-Fi coverage, plan the cable route before you buy the cable.

Why does my Wi-Fi keep dropping even though the router lights look fine?

Check that the ethernet cable is fully inserted into both the modem and the router — a partially loose cable can cause intermittent disconnections. If the cable is tight, restart both devices by unplugging them for 30 seconds. If the problem continues, move the router away from metal objects, microwaves, or cordless phones, which can interfere with Wi-Fi signals.