Connect Your Modem to Power and Cable
Start by placing your modem in a central location in your home—ideally near where your cable line enters the building. Keep it away from microwaves, cordless phones, and metal objects, which can interfere with the signal. Make sure the modem has good air circulation around it and is not in a closed cabinet.
Plug the power cable into the back of the modem, then into a wall outlet or power strip. Wait 30 seconds for the modem to begin its startup sequence. You will see lights on the front of the unit start to flash.
Take the coaxial cable (the thick cable with a threaded connector) that comes from your wall outlet or cable box and screw it firmly into the port labeled "Cable In" on the back of the modem. Turn it clockwise until it is snug—do not over-tighten, as this can damage the connector. This is the only cable connection the modem needs to receive internet service.
Key Takeaways
- Place your modem in a central location away from interference sources like microwaves and metal objects.
- Connect the coaxial cable from your wall outlet to the "Cable In" port on the back of the modem.
- Wait three to five minutes after powering on for all lights to stabilize before moving to the next step.
- Write down your modem's MAC address (found on a sticker on the bottom or back) before you register it with Xfinity.
- If the online registration does not work, call Xfinity at 1-800-934-6489 to register by phone instead.
Wait for the Modem to Boot Up Completely
The modem needs three to five minutes to fully start up after you plug it in. During this time, you will see the lights on the front change. The Power light should turn solid white or green. The Online light will blink while the modem is connecting to Xfinity's network, then turn solid when the connection is established.
Do not unplug the modem or move it during this startup period. If you see a red light or the Online light does not turn solid after five minutes, unplug the modem, wait 30 seconds, and plug it back in. This is called a power cycle and fixes most connection problems.
Find Your Modem's MAC Address
Before you can register your modem with Xfinity, you need its MAC address (Media Access Control address). This is a unique identifier printed on a sticker on the bottom or back of the modem. It looks like this: 00:1A:2B:3C:4D:5E (six pairs of letters and numbers separated by colons or hyphens).
Write this number down or take a photo of it with your phone. You will need it in the next step. Some modems also display the MAC address on the front screen or in the modem's settings menu, which you can access by typing 192.168.0.1 into a web browser on a computer connected to the modem.
Register Your Modem Online or by Phone
Go to xfinity.com/set up or call Xfinity at 1-800-934-6489. If you register online, you will need your Xfinity account number (found on your bill), your MAC address, and your service address. The online form will ask you to confirm these details and may ask you to create or sign into your Xfinity account.
Registration usually takes five to ten minutes online. After you submit your information, Xfinity's system will send a signal to your modem to set up it. You will see a confirmation message on the screen. If you prefer to register by phone, a representative can walk you through the process and answer questions about your service.
If you do not have an Xfinity account yet because this is a new service, the representative or online form will help you set one up at the same time.
Connect Your Router (If You Have One)
If you want to use Wi-Fi, you will need a router. Some Xfinity customers rent a combined modem-router unit from Xfinity, in which case you skip this step. If you have a separate router, connect an ethernet cable from one of the ports labeled "Ethernet" on the back of the modem to the port labeled "Internet" or "WAN" on the back of your router.
Power on the router and wait two to three minutes for it to connect to the modem. You should see lights on the router turn solid. The Wi-Fi network name (SSID) and password are usually printed on a sticker on the router itself. Use these to connect your phone, laptop, or other devices to Wi-Fi.
If you do not see a Wi-Fi network name on your router, check the router's instruction manual or log into the router's settings by typing 192.168.1.1 into a web browser. Most routers have a default username and password printed on the device.
Test Your Connection
Once your modem is registered and all lights are solid, open a web browser on any device and try to visit a website like google.com. If the page loads, your internet connection is working. If the page does not load, wait another minute and try again—sometimes registration takes a few extra moments to complete.
If you still cannot reach any websites after five minutes, unplug the modem for 30 seconds, plug it back in, and wait for the Online light to turn solid again. If the problem continues, check that the coaxial cable is screwed in tightly at both the wall outlet and the modem. A loose connection is the most common reason for no internet.
Troubleshoot Common Problems
If the Online light is red or blinking red, the modem cannot reach Xfinity's network. First, make sure the coaxial cable is connected firmly to both the wall outlet and the modem. If the cable is loose, tighten it and wait two minutes. If the light is still red, unplug the modem for one minute, then plug it back in.
If the modem has power but no lights are on at all, the power cable may not be fully inserted into the outlet or the modem itself. Try a different outlet to rule out a problem with the wall socket. If you still see no lights after trying a different outlet, the modem may have a hardware problem and you should contact Xfinity for a replacement.
If your internet is very slow or keeps dropping, move the modem away from walls, metal objects, and other electronics. Microwaves and cordless phones especially can interfere with the signal. If you are using Wi-Fi, move closer to the router or try connecting a device with an ethernet cable to see if the problem is with the Wi-Fi or the internet itself.
Frequently Asked Questions
Do I need to call Xfinity to set up my modem, or can I do it online?
You can do it either way. Online registration at xfinity.com/set up is faster if you have your account number and MAC address ready. Calling 1-800-934-6489 takes longer but a representative can answer questions and troubleshoot if something goes wrong during setup.
What if I do not know my Xfinity account number?
Check your Xfinity bill—the account number is printed near the top. If you do not have a bill yet because this is new service, the online registration form or phone representative can look up your account using your service address and phone number.
Can I use any router with my Xfinity modem?
Yes. Any standard Wi-Fi router will work with an Xfinity modem as long as you connect it with an ethernet cable from the modem's Ethernet port to the router's Internet or WAN port. You do not have to use Xfinity's router.
How long does it take for the modem to set up after I register it?
Online registration usually activates the modem within five to ten minutes. Phone registration can take up to 30 minutes. If your modem does not connect after 30 minutes, unplug it for one minute and plug it back in, then wait another five minutes.
What does it mean if the Online light is blinking instead of solid?
A blinking Online light means the modem is still connecting to Xfinity's network. Wait two to three minutes for it to turn solid. If it blinks for more than five minutes, the modem may not be registered yet or the coaxial cable may be loose. Check the cable connection and make sure you completed the registration step.