Unpack and Position Your Router Before Plugging It In

Remove your Xfinity router from the box and set it on a flat, elevated surface in a central location in your home. A shelf, bookcase, or table works better than the floor or inside a cabinet—walls and metal objects block the wireless signal. Keep the router at least a few feet away from your modem, even though they will be connected by cable. If your modem is in a closet or corner, place the router in a more open area of your home.

Check that you have the power cable, an ethernet cable, and the router itself. The ethernet cable connects your modem to the router's port labeled "Internet" or "WAN" (Wide Area Network). Do not plug anything in yet. Take a moment to locate the reset button on the back of the router—it is usually a small recessed button you would press with a paperclip. You will not need it for a normal setup, but knowing where it is prevents confusion later.

Connect the Ethernet Cable Between Your Modem and Router

Locate the ethernet cable in your router box. One end plugs into your modem's ethernet port (usually labeled "Ethernet" or "Out"), and the other end plugs into your router's "Internet" or "WAN" port. The cable clicks in place with a small clip—push until you hear or feel it lock. This cable carries the internet signal from your modem to your router, which then broadcasts it wirelessly throughout your home.

If your modem is already powered on and working, you should see lights on the modem change or blink when you plug in the ethernet cable. This is normal. The modem is detecting the router on the other end of the cable. Wait 10 to 15 seconds before moving to the next step.

Plug In the Router and Wait for Startup

Connect the power cable to the back of the router and plug it into a wall outlet or power strip. The router will take 2 to 3 minutes to fully start up. During this time, you will see lights on the front of the router turn on, blink, and then settle into a steady pattern. A solid light usually means the connection is active; a blinking light means the router is still communicating with the modem.

Do not unplug the router during startup, even if the lights seem to be taking a while. Let it sit for the full 3 minutes. Once the lights have stopped changing and appear steady, the router is ready to use. If you see a red light or no lights at all after 5 minutes, check that the power cable is fully inserted into both the router and the wall outlet.

Key Takeaways

  • Position your router in a central, elevated location away from walls and metal objects to get the strongest wireless signal throughout your home.
  • Connect the ethernet cable from your modem's output port to your router's "Internet" or "WAN" port before powering on the router.
  • Allow 2 to 3 minutes for the router to fully start up after you plug it in; do not unplug it during this time.
  • Once the lights on the front of the router stop blinking and appear steady, the hardware setup is complete and you can connect devices wirelessly.

Connect Your Devices to the Router's Wireless Network

On your phone, tablet, or computer, open the Wi-Fi settings and look for your Xfinity router's network name. The network name (also called the SSID) is printed on a sticker on the back or bottom of the router. It usually looks like "XFINITY-" followed by numbers or letters. Select this network from your device's Wi-Fi list.

When prompted for a password, use the Wi-Fi password printed on the same sticker as the network name. Type it exactly as shown—uppercase and lowercase letters matter. Once you enter the password, your device will connect to the router. You should now have internet access. Test this by opening a web browser and visiting a website like google.com.

Log Into the Router's Settings If You Need to Change the Network Name or Password

The default network name and password work fine for most people, but you can change them if you want something easier to remember. Open a web browser on any device connected to the router and type 192.168.0.1 into the address bar. This takes you to the router's settings page.

You will be asked to log in. The default username is admin and the default password is motorola (or sometimes motorola123). Once logged in, look for a section labeled "Wi-Fi" or "Wireless Settings." From there you can change the network name and password to anything you choose. Write down your new password somewhere safe before you log out. After you change these settings, all your devices will need to reconnect using the new password.

Troubleshoot If Your Router Is Not Connecting to the Internet

If your router powers on but shows no internet light or will not connect your devices to the internet, first check that the ethernet cable is fully clicked into both the modem and the router. Unplug the cable from both ends, wait 10 seconds, and plug it back in firmly. Then restart the modem by unplugging its power cable for 30 seconds, plugging it back in, and waiting 2 minutes for it to fully restart.

Once the modem is back on, restart the router the same way: unplug it, wait 30 seconds, and plug it back in. This full restart often fixes connection problems. If the router still does not show an internet light after 5 minutes, the issue may be with your modem or internet service rather than the router itself. Contact your internet service provider to confirm your modem is working correctly.

Frequently Asked Questions

Can I use my old router instead of the Xfinity router?

Yes, you can use a third-party router with Xfinity internet. Connect it to your modem the same way—ethernet cable from the modem's output to the router's WAN port. You will need to log into that router's settings to set up the network name and password. Check your router's manual or the manufacturer's website for the default login information and setup steps, as they vary by brand.

What if I do not see my router's network name in the Wi-Fi list?

Wait a full 3 minutes after plugging in the router before checking. If the network still does not appear, restart the router by unplugging it for 30 seconds and plugging it back in. If it still does not show up after another 3 minutes, check that the ethernet cable is fully connected to both the modem and the router. A loose cable is the most common reason the router cannot detect the internet signal.

Do I need to restart my modem when I install the router?

You do not have to restart it before installation, but restarting both the modem and router together after everything is plugged in can help them communicate better. Unplug the modem first, wait 30 seconds, plug it back in, and wait 2 minutes. Then unplug the router, wait 30 seconds, and plug it back in. This full restart takes about 5 minutes total but often prevents connection problems.

Where should I place the router for the best Wi-Fi signal?

Place it in a central location on a shelf or table, away from walls, metal objects, and appliances like microwaves or cordless phones. Higher placement is better than lower—a router on a shelf reaches more of your home than one on the floor. Avoid putting it inside a cabinet or closet, even if that is where your modem is. If your modem must stay in a closet, run the ethernet cable to a more open area for the router.

Can I move the router to a different room after installation?

Yes, you can move it anytime. Just unplug the power cable and the ethernet cable, move the router to the new location, and plug both cables back in. The router will restart and reconnect to the modem automatically. Your devices will stay connected to the network as long as they are within range of the new location.