A factory reset clears all settings and returns your modem to its original state
An Arris modem reset wipes out your current configuration and restores the modem to factory defaults. This means your internet connection will stop working until you set it up again with your internet service provider (ISP). A reset is useful when your modem is unresponsive, won't connect to the internet, or you're preparing to return it to your ISP—but it's a last resort, not a first step. Most connection problems can be fixed by power-cycling (unplugging and replugging) or rebooting through the modem's settings menu.
Before you reset, understand that you will need to contact your ISP to restore your connection afterward. Write down your account number and have your ISP's phone number ready before you start. A reset takes 20 to 30 minutes total, including the time for your ISP to re-provision the modem remotely.
Key Takeaways
- Power-cycling your modem by unplugging it for 30 seconds fixes most connection problems and should be your first troubleshooting step.
- A factory reset erases all settings and requires you to set up your internet connection again with your ISP, so only do this if other steps fail.
- The reset button on an Arris modem is recessed and requires a paperclip or pin held for 10 to 15 seconds to set up.
- After a reset, your modem will restart and show default lights; contact your ISP to re-provision it before you can use the internet again.
- If your modem is still unresponsive after a reset, the hardware may be failing and you should contact your ISP for a replacement.
Power-cycle your modem before attempting a reset
Power-cycling is the simplest fix and solves most temporary connection issues. Unplug the power cable from the back of your Arris modem and wait 30 seconds. This clears the modem's memory and allows it to restart fresh. Plug the power cable back in and wait two to three minutes for the modem to fully boot up. Watch the lights on the front: you should see a power light come on, followed by internet and online lights that eventually turn solid or stop blinking.
If your modem has a battery backup (some models do), unplugging alone won't fully power it down. In that case, hold the power button on the back of the modem for 10 seconds while it's unplugged, then plug it back in. This drains any remaining charge and forces a complete restart. Try power-cycling at least once before moving on to a factory reset.
Locate the reset button on your Arris modem
The reset button on Arris modems is small and recessed into the back or bottom of the unit—it's deliberately hard to press by accident. Look for a tiny hole labeled "Reset" near the power port or on the underside of the modem. You'll need a straightened paperclip, a ballpoint pen, or a thumbtack to reach it. Do not use your finger; the button is designed to be inaccessible without a tool.
If you cannot find the reset button, check the model number on the bottom or back of your modem and search the manufacturer's documentation online. Different Arris models (SB, MG, CM series) have slightly different layouts, and some older models may have the button in a different location. The model number usually starts with "SB" or "MG" followed by numbers.
Perform a factory reset on your Arris modem
Before you reset, understand that you will lose your internet connection and will need to contact your ISP to restore it. Write down your account number and have your ISP's phone number ready. With the modem powered on, insert your tool into the reset hole and press the button firmly. Hold it down for 10 to 15 seconds—you may feel a slight click or resistance. Do not release early; the modem needs the full duration to trigger the reset.
The modem will restart automatically. You'll see the lights go dark, then the power light will come back on. Wait three to five minutes for the modem to fully reboot. The lights will cycle through different colors or patterns as it initializes. Once the lights stabilize (usually with the power light solid and other lights off or blinking slowly), the reset is complete and the modem is back to factory settings.
Set up your modem again after a factory reset
After a factory reset, your modem has no internet configuration. Call your ISP's customer service number and tell them you've reset your modem and need to re-provision it. Have your account number and the modem's serial number (printed on the back or bottom) ready. Your ISP will push new settings to the modem remotely, a process that usually takes five to ten minutes.
While you wait for your ISP to re-provision the modem, watch the lights. You should see the internet light come on and eventually turn solid or show a steady pattern. Once your ISP confirms the modem is provisioned, connect a device to the modem's Wi-Fi network or plug in an ethernet cable and test your connection. If the connection still doesn't work after re-provisioning, contact your ISP again—there may be an issue with your account or the modem itself.
When to reboot instead of resetting
A reboot is different from a reset and is much safer to try first. A reboot restarts the modem without erasing settings. Most Arris modems allow you to reboot through the web interface: open a browser, type 192.168.0.1 into the address bar, and log in (the default username is often "admin" and the password is on the modem's label). Look for a "Reboot" or "Restart" button in the settings menu and click it. The modem will restart in about two minutes and keep all your settings intact.
If you can't access the web interface, a power-cycle (unplugging for 30 seconds) is the next best option. Only perform a factory reset if the modem is completely unresponsive, won't connect to the internet after multiple power-cycles, or you're returning it to your ISP. Rebooting and power-cycling are reversible; a factory reset is not.
Troubleshoot if the modem won't respond after a reset
If your modem still won't connect to the internet after a reset and re-provisioning, or if it won't power on at all, the hardware may be failing. Check that the power cable is firmly seated in both the modem and the wall outlet. Try a different outlet to rule out a tripped breaker or dead circuit. If the modem still won't power on, the power supply may be defective.
If the modem powers on but won't connect even after your ISP re-provisions it, contact your ISP's technical support. They can check whether the modem is recognized on their network and whether there's an account issue preventing connection. If the modem is more than five to seven years old, your ISP may recommend replacing it—older modems sometimes lose the ability to hold a connection reliably. Document what you've tried (power-cycle, reset, re-provisioning) so you can tell the technician.
Frequently Asked Questions
Will a reset delete my Wi-Fi password?
Yes. A factory reset erases all settings, including your Wi-Fi network name and password. After re-provisioning, you'll need to set up a new Wi-Fi network. Log into the modem's web interface at 192.168.0.1 and create a new network name and password in the wireless settings.
How long does it take for an Arris modem to reset?
The reset button press itself takes 10 to 15 seconds. The modem then restarts, which takes three to five minutes. Re-provisioning by your ISP adds another five to ten minutes. Total time from pressing reset to having internet again is usually 20 to 30 minutes.
Can I reset my modem if it's still under warranty?
A factory reset does not void your warranty. However, if the modem is defective and won't work even after a reset and re-provisioning, contact your ISP or the manufacturer about a replacement. Keep your proof of purchase or account information handy.
What's the difference between a soft reset and a hard reset?
A soft reset is a reboot through the web interface or power button—it restarts the modem but keeps your settings. A hard reset is pressing the recessed reset button and erases all settings. Use a soft reset first; only do a hard reset if the modem is unresponsive.
Do I need to unplug my modem before pressing the reset button?
No. Press the reset button while the modem is powered on. The modem will restart on its own. Unplugging first is not necessary and may delay the reset process.