Connect the modem to power and your internet line

An Arris modem connects to two things: your cable line (the coaxial cable from your wall) and a power outlet. Start by plugging the modem into power — you'll see lights begin to flash on the front panel within a few seconds. Do not unplug it yet; those lights are telling you the modem is starting up.

Next, take the coaxial cable (the thick cable with a threaded connector, usually already running from your wall) and screw it firmly into the port labeled "Cable In" on the back of the modem. Turn it by hand until it's snug — you should not need a wrench. The modem will now begin to detect your internet signal.

Wait two to three minutes without touching anything. The lights on the front will cycle through different colors and patterns. This is normal. The modem is scanning for your internet service provider's signal and downloading its configuration.

Key Takeaways

  • Plug the modem into power first, then connect the coaxial cable from your wall to the "Cable In" port on the back.
  • Wait two to three minutes for the modem to detect the signal and finish its startup sequence before moving to the next step.
  • Once the lights stabilize (usually a solid or slowly blinking light), the modem is ready to connect to a router or computer.
  • If you see a red light or no lights after five minutes, restart the modem by unplugging it for 30 seconds, then plug it back in.
  • Write down the modem's MAC address (printed on the sticker on the back) in case your internet provider needs it later.

Understand what the lights mean

The front panel of an Arris modem has several lights, and each one tells you something about what the modem is doing. The Power light should be solid green or white once the modem is plugged in. If it's off or red, the modem is not receiving power or has a hardware problem.

The Online light (sometimes labeled "Internet" or "Downstream") is the most important one. During startup, it will blink amber or red as the modem searches for your internet signal. Once it turns solid green, the modem has found the signal and is ready to use. This usually takes two to five minutes.

The Upstream light shows whether the modem can send data back to your internet provider. It should also be solid green once the modem is fully online. If the Online light is green but Upstream is red or off, restart the modem by unplugging it for 30 seconds.

If you see a red Online light that does not change to green after five minutes, the modem is not detecting your internet signal. Check that the coaxial cable is screwed in tightly, and that it's connected to the correct port on the back of the modem.

Connect a router or computer to the modem

Once the Online light is solid green, the modem is ready to share internet. You can connect a router (which broadcasts Wi-Fi) or a computer directly to the modem using an Ethernet cable.

If you're using a router, plug one end of an Ethernet cable into the port labeled "Ethernet" on the back of the modem, and the other end into the port labeled "Internet" or "WAN" on the back of your router. The router will now receive internet from the modem. Wait another minute for the router to start up, then look for your Wi-Fi network name on your phone or computer.

If you're connecting a computer directly to the modem, plug an Ethernet cable into the "Ethernet" port on the modem and into the Ethernet port on your computer. Your computer should detect the internet connection within a few seconds.

Restart the modem if something goes wrong

A restart fixes most modem problems and takes less than two minutes. Unplug the modem from the power outlet and wait 30 seconds. This clears the modem's memory and forces it to start fresh. Then plug it back in and wait for the lights to cycle through their startup sequence again.

If the Online light is still red or off after a full restart, the problem is likely with your internet service or the cable line itself. Check that the coaxial cable is screwed in firmly at both the wall and the modem. If it is, contact your internet provider — they can check whether there's a signal problem on their end.

Do not restart the modem more than once every 10 minutes. Restarting too often can confuse the modem and make it take longer to come back online.

Find your modem's IP address if you need to change settings

Most Arris modems work fine without any manual changes. However, if you need to log in to the modem to check settings or restart it remotely, you'll need its IP address. This is a set of four numbers separated by periods, like 192.168.0.1.

On a Windows computer, open Command Prompt (search for "cmd" in the Start menu), type ipconfig, and press Enter. Look for the line that says "Default Gateway" — that number is usually your modem's IP address. On a Mac, open Terminal (search for "Terminal" in Spotlight), type netstat -nr | grep default, and press Enter. The first number in the output is your modem's IP address.

Once you have the IP address, open a web browser and type it into the address bar (for example, 192.168.0.1). You'll be asked to log in. The default username is usually "admin" and the default password is usually "motorola" for Arris modems, though your internet provider may have changed this. If you don't know the password, contact your provider.

Check the modem's MAC address for your internet provider

Your internet provider may ask for your modem's MAC address (Media Access Control address) when you set up service or troubleshoot a problem. This is a unique identifier printed on a sticker on the back or bottom of the modem. It looks like six pairs of letters and numbers separated by colons, such as 00:1A:2B:3C:4D:5E.

Write this number down or take a photo of the sticker and keep it somewhere safe. You may need it if you call your provider for support, or if you move the modem to a different location and need to re-register it on their network.

Frequently Asked Questions

How long should it take for the modem to come online?

Most Arris modems reach full online status (solid green Online light) within two to five minutes of being plugged in. If it takes longer than 10 minutes, restart the modem by unplugging it for 30 seconds. If the Online light is still red after a restart, contact your internet provider to check for signal problems on their network.

Can I use the modem without a router?

Yes. You can plug a computer directly into the modem's Ethernet port and use the internet without a router. However, you won't have Wi-Fi — only devices connected by Ethernet cable will work. Most people use a router so they can connect phones, tablets, and laptops wirelessly.

What if the lights are off but the modem is plugged in?

Check that the power cable is fully inserted into both the modem and the wall outlet. If it is, try a different outlet to rule out a dead power socket. If the lights still don't turn on, the modem may have a hardware failure and will need to be replaced by your internet provider.

Do I need to do anything after the modem is online?

No. Once the Online light is solid green and you've connected a router or computer, the modem is ready to use. You don't need to log in or change any settings unless your internet provider tells you to, or unless you want to restart the modem remotely.

What's the difference between restarting and resetting the modem?

Restarting means unplugging it and plugging it back in — this clears temporary problems but keeps your settings. Resetting means holding a small button on the back for 10 seconds, which erases all settings and returns the modem to factory defaults. Only reset if your provider tells you to, because it will erase any custom settings they've made.