Connect the modem to power and your internet line
Start by placing your Arris modem in a central location in your home — ideally near where your internet line enters the building and away from walls or metal objects that can weaken the signal. Plug the power cable into the back of the modem and into a wall outlet. You should see lights begin to appear on the front panel within a few seconds.
Next, take the coaxial cable (the thick cable with a threaded connector) that comes from your wall jack or cable box and screw it firmly into the port labeled "Cable In" on the back of the modem. Turn it by hand until it is snug — do not force it. This is the connection that brings your internet signal into the modem.
If you are setting up a modem-router combo unit (like an Arris SB8200 with built-in WiFi), you can skip the ethernet step below. If you have a modem-only unit, continue to the next step.
Connect your devices with an ethernet cable
Take an ethernet cable and plug one end into the port labeled "Ethernet" or "LAN" on the back of the modem. Plug the other end into your router, computer, or another device. This creates a wired internet connection while the modem boots up and registers with your internet service provider.
If you are using a modem-router combo, the WiFi network will broadcast automatically once the modem finishes starting up. You do not need to plug in an ethernet cable unless you want a wired connection for a specific device.
Wait for the modem to fully boot and register
The startup process takes between 2 and 5 minutes. During this time, watch the lights on the front of the modem. You will see them change color and blink as the modem goes through its startup sequence. The lights tell you what is happening:
- Power light: Should be solid green or white once power is connected.
- Downstream light: Blinks while the modem reads the signal from your cable line, then turns solid when it locks on.
- Upstream light: Blinks while the modem sends data back to your provider, then turns solid when the connection is established.
- Online light: Turns solid green or white when the modem has registered with your internet service provider and is ready to use.
Do not unplug the modem during this process. If the lights do not change after 10 minutes, or if the Online light never turns solid, move to the troubleshooting section below.
Log in to the modem's settings page
Once the Online light is solid, open a web browser on any device connected to the modem and type 192.168.0.1 or 192.168.100.1 into the address bar. Press Enter. You should see a login page for your Arris modem.
The default username is usually admin and the default password is motorola (or sometimes admin). Enter these credentials and click Log In. If these do not work, check the sticker on the back or bottom of your modem — it may have different default credentials printed there.
Once you are logged in, you can see the modem's status, check your internet speed, and view connected devices. Most users do not need to change any settings here. The modem is now working.
Set up WiFi on a modem-router combo unit
If you have an Arris modem with built-in WiFi (like the SB8200 or G36), the WiFi network broadcasts automatically with a default name and password. You can find the network name and password on the sticker attached to the modem.
To change the WiFi name or password to something easier to remember, log in to the settings page at 192.168.0.1 or 192.168.100.1, then look for a section labeled "WiFi" or "Wireless". From there you can create a new network name and password. Write down your new password somewhere safe — you will need it when you connect phones, tablets, and other devices.
If you do not see a WiFi section in the settings, your modem is a modem-only unit and does not have WiFi built in. In that case, connect your router to the modem using an ethernet cable and set up the router's WiFi separately using the router's own settings page.
Troubleshoot if the modem does not connect
If the Online light does not turn solid after 10 minutes, or if you cannot reach the internet, start with these steps. First, unplug the modem's power cable, wait 30 seconds, and plug it back in. This resets the modem and often clears temporary connection problems. Wait another 5 minutes for it to boot.
If that does not work, check that the coaxial cable from the wall is screwed in tightly to the "Cable In" port. A loose connection is the most common reason a modem will not register. If the cable is loose, tighten it by hand and wait 2 minutes.
If the lights still do not change, or if you see a red light instead of green, the problem may be on your internet service provider's end or the modem itself may be faulty. Contact your provider's support line — they can check whether your modem is registered on their network and whether there is an outage in your area. Have your modem's serial number ready; it is printed on the sticker on the back.
Key Takeaways
- Place the modem in a central location, plug in power, and connect the coaxial cable from your wall jack to the "Cable In" port on the back.
- The modem takes 2 to 5 minutes to start up and register with your internet service provider; the Online light turning solid green means it is ready.
- You can log in to the modem's settings at 192.168.0.1 or 192.168.100.1 using the default username admin and password motorola to check status or change WiFi settings.
- If the modem does not connect, unplug it for 30 seconds, check that the coaxial cable is tight, and then contact your internet provider if the problem continues.
- On a modem-router combo unit, WiFi broadcasts automatically with a default name and password printed on the modem's sticker.
Frequently Asked Questions
What do the lights on the front of the modem mean?
The Power light shows the modem has electricity. The Downstream and Upstream lights show the modem is communicating with your provider's network. The Online light turning solid green means the modem is registered and ready to use. If any light stays red or does not light up, the modem is still starting or there is a connection problem.
Can I use my own modem instead of renting one from my provider?
Yes, if your provider allows it. Arris modems are compatible with most major cable internet providers in the United States, but you should check your provider's list of approved modems before buying. Your provider can tell you which Arris models work on their network.
Do I need to restart the modem after I set it up?
No, once the modem is fully booted and the Online light is solid, it is ready to use. You do not need to restart it unless you are troubleshooting a connection problem or your provider asks you to.
What if I forgot the WiFi password?
The default password is printed on the sticker attached to the modem. If you changed the password and forgot it, you can reset the modem to factory defaults by holding the Reset button on the back for 10 seconds. This will erase your custom WiFi name and password and restore the defaults, so you will need to set them up again.
Is it safe to leave the modem plugged in all the time?
Yes, modems are designed to run continuously. Leaving it plugged in does not damage the device or use a significant amount of electricity. You can unplug it if you are away for an extended period, but there is no need to turn it off daily.