The right way to disconnect your modem from power
Unplugging a modem is straightforward: locate the power cable at the back of the unit, grip it near the connector (not the cord itself), and pull it straight out. If the cable is tight, wiggle it gently side to side as you pull. Do not yank the cord or pull at an angle — this can damage the connector on the modem or the power adapter. Once the cable is free, the modem will shut down within seconds.
Most modems have no on/off switch, so unplugging is the only way to cut power completely. Some models have a power button on the front or back, but pressing it usually just puts the device into a low-power state rather than shutting it off entirely. If your modem has a button, unplugging is still the more thorough method.
You do not need to do anything before unplugging — there is no shutdown sequence to run or data to save. The modem stores its settings in memory that persists even when power is off, so your internet configuration will remain intact when you plug it back in.
Key Takeaways
- Grip the power connector itself, not the cord, and pull straight out to avoid damaging the cable or the modem's port.
- The modem will shut down completely within seconds of being unplugged, even if it has a power button on the front.
- Your internet settings and account information stay saved in the modem's memory, so you do not lose anything by unplugging it.
- Wait 30 seconds after unplugging before plugging it back in if you are trying to restart your connection or fix a problem.
- Unplugging is safe to do at any time — there is no risk of data loss or corruption from a sudden power cut.
When to unplug your modem
Unplug your modem when you need to restart your internet connection. If your internet has stopped working, unplugging for 30 seconds and plugging it back in will often restore service. This works because it clears temporary errors in the modem's memory and forces it to reconnect to your internet service provider.
You should also unplug the modem if you are moving it to a different location, replacing it with a new one, or performing maintenance on your network equipment. Unplugging before you disconnect cables prevents electrical surges and protects both the modem and your router or other devices connected to it.
Unplug the modem during thunderstorms if you want extra protection against lightning damage, even though most modern modems have surge protection built in. If your area experiences frequent power outages, unplugging the modem during an outage can prevent damage when power returns suddenly.
What happens when you unplug the modem
The modem loses all power when ready and shuts down. Any lights on the front of the unit will turn off. If you have a router connected to the modem, the router will lose its internet connection but will remain powered on if it has its own power cable — your Wi-Fi will stay active but will not connect to the internet.
Your internet service provider will see the modem as offline. If you leave it unplugged for more than a few minutes, your ISP may send you a notification that your modem is not responding. This is normal and will clear once you plug the modem back in and it reconnects.
Any devices using your internet will lose their connection. Computers, phones, and smart devices connected to your Wi-Fi will show "no internet" or "connected but no internet access." They will automatically reconnect once the modem is back online, usually within 30 to 60 seconds.
How to plug the modem back in
Locate the power cable you unplugged and insert the connector back into the port on the modem. Push it in firmly until you hear or feel a click — the connector should sit flush against the modem's back panel. Plug the other end of the power cable into a wall outlet or power strip.
The modem will begin starting up. You will see lights on the front of the unit turn on in sequence — usually a power light first, then lights for internet connection and activity. Wait 60 to 90 seconds for all lights to stabilize. Once the internet light stops blinking and stays solid, the modem is fully connected and ready to use.
If the internet light does not turn solid after two minutes, unplug the modem again, wait 30 seconds, and plug it back in. If the problem persists, contact your internet service provider to check whether there is an outage in your area or a problem with your account.
Protecting your modem when unplugging
Use a power strip with a surge protector rather than plugging the modem directly into a wall outlet. This protects the modem from voltage spikes that can occur when power is restored after an outage. If you do unplug the modem during a storm or outage, the surge protector will absorb the spike when you plug it back in.
Keep the power cable in good condition. If the cable is frayed, cracked, or discolored, replace it before using the modem again. A damaged cable can cause electrical hazards and may not deliver stable power to the modem, leading to connection problems.
Do not unplug the modem by pulling on the cord itself — always grip the connector. Pulling on the cord can damage the internal wires and create a fire hazard. If the connector is stuck, unplug the power strip instead of forcing the cable.
Unplugging vs. using a power button
If your modem has a power button, pressing it may not fully cut power to the device. Many modems with buttons enter a standby mode that keeps some circuits active and still draws a small amount of electricity. Unplugging removes all power and is the only way to may support the modem is completely off.
Some newer modems have a power button that does fully shut down the device when pressed. Check your modem's manual to see whether the button cuts power completely or just enters standby. If you are unsure, unplugging is always the safer choice and will definitely turn the modem off.
For a full restart — which is what you need to fix most internet problems — unplugging is more reliable than pressing a power button. The 30-second wait after unplugging gives the modem's capacitors time to fully discharge, which clears more temporary errors than a button press alone.
Frequently Asked Questions
Will unplugging the modem delete my saved passwords or settings?
No. Your modem stores its configuration and account information in permanent memory that does not require power. When you plug the modem back in, it will reconnect to your internet service provider using the same settings it had before. Your Wi-Fi password and network name will also remain unchanged.
How long should I wait after unplugging before plugging it back in?
Wait at least 30 seconds. This gives the modem's internal capacitors time to fully discharge, which clears temporary errors more effectively than a shorter wait. If your internet is still not working after a 30-second restart, wait a full two minutes before plugging it back in and trying again.
Is it safe to unplug the modem while it is actively transferring data?
Yes. Unplugging the modem will not corrupt any files on your computer or damage the modem itself. Any data transfer in progress will straightforward stop, but your files will remain intact. The modem has no moving parts or data that can be harmed by a sudden power loss.
Can I unplug the modem and router at the same time?
Yes, you can unplug both at the same time if you want to restart your entire network. Unplug the modem first, then the router. When plugging them back in, plug the modem in first and wait for it to fully connect (60 to 90 seconds) before plugging in the router. This ensures the modem is ready to provide internet to the router.
What if the modem does not turn back on after I plug it in?
Check that the power cable is fully inserted into both the modem and the wall outlet. Try a different outlet to rule out a tripped breaker. If the modem still does not power on, the power adapter may be faulty. Contact your internet service provider — they can send you a replacement modem and power supply.