The Basic Setup: Router One Plugs Into the Modem, Router Two Plugs Into Router One
You can use two routers with one modem by connecting them in a chain. The modem connects to your first router (the main one), and the second router connects to the first router using an ethernet cable. This is called daisy-chaining, and it works because the first router acts as both a receiver of the internet signal and a sender of that signal to the second router.
The modem itself does not change. It still receives the internet from your service provider and passes it to the first router exactly as it would with a single router. The first router then shares that connection with the second router, which broadcasts its own wireless network in a different part of your home or building.
This setup is straightforward to install and requires no special configuration on the modem side. You plug in cables, power on both routers, and they work. However, there are limits to how well this works and some trade-offs you should understand before you start.
Key Takeaways
- The simplest setup connects the modem to Router 1, then Router 1 to Router 2 using an ethernet cable, with both routers broadcasting separate wireless networks.
- Daisy-chaining routers cuts the available bandwidth roughly in half because the second router must send and receive data through the first router on the same wireless channel.
- You should disable the second router's DHCP server so it does not try to assign IP addresses, preventing conflicts and confusion on your network.
- If you need full speed in multiple locations, a mesh system or access point is more effective than two traditional routers, though it requires replacing your equipment.
How to Connect the Cables and Power
Start with the modem powered on and working normally. Take an ethernet cable and plug one end into the ethernet port on the back of the modem. Plug the other end into the WAN port (or Internet port) on your first router. This port is usually a different color from the other ethernet ports and is labeled clearly on the back of the router.
Power on the first router and wait for its lights to stabilize—usually two to three minutes. Once the first router is fully booted, take a second ethernet cable and plug one end into any of the regular ethernet ports (not the WAN port) on the first router. Plug the other end into the WAN port on the second router.
Power on the second router and wait for it to boot. Both routers should now have internet access. You can test this by connecting a device to the second router's wireless network and opening a web browser. If the page loads, the connection is working.
Disable DHCP on the Second Router to Avoid IP Address Conflicts
A DHCP server is the part of a router that assigns IP addresses to devices that connect to it. By default, both routers will try to do this, which creates a conflict: your devices will receive instructions from two different sources about what address to use, causing connection problems and slow speeds.
To fix this, you need to turn off DHCP on the second router only. Log into the second router's admin panel by opening a web browser and typing the router's IP address (usually printed on the back of the router or in its manual—often something like 192.168.1.1 or 192.168.0.1). Enter the username and password (also on the back or in the manual).
Once logged in, look for a section called DHCP, LAN Settings, or Network Settings. The exact location varies by router brand and model. Find the option to enable or disable DHCP and set it to Off or Disabled. Save the changes. The second router will now only broadcast a wireless signal and pass traffic through to the first router, without trying to manage IP addresses.
What to Expect: Speed Loss and When This Setup Works Well
When you daisy-chain routers, the second router must send and receive all its data through the first router. This means the bandwidth available to devices on the second router is roughly half of what it would be with a single router, because the first router is using the same wireless channel to talk to both its own devices and the second router.
This setup works well if you need wireless coverage in a distant room and do not need high speeds there. A bedroom on the far side of a house, a garage, or a basement are good examples. It also works if you have a small number of devices on the second router and they do not all need to transfer large files at once.
This setup does not work well if you need full speed in the second location, if you have many devices on the second router, or if you regularly transfer large files between the two networks. In those cases, you should consider a mesh system (which uses special hardware designed to work together) or a wireless access point (which is simpler than a router and designed specifically for extending coverage).
Naming the Networks So You Know Which Router You Are Connected To
By default, both routers will broadcast wireless networks with their own names (SSIDs). You might see "NETGEAR-5G" and "NETGEAR-5G-2" or similar. To avoid confusion, you should rename them so you know which one you are connecting to.
Log into each router's admin panel separately and look for a section called Wireless Settings, WiFi Settings, or SSID. Change the name of the first router to something like "Home-Main" and the second to "Home-Bedroom" or "Home-Garage"—whatever describes its location. Save the changes.
You can also set both routers to use the same password for convenience, so you do not have to remember two different ones. This is optional but makes connecting devices easier.
When to Call a Professional or Replace Your Setup
If you have followed these steps and devices on the second router are not connecting, or connections keep dropping, the problem is usually one of three things: the DHCP server on the second router was not fully disabled, the ethernet cable between the routers is loose or damaged, or the second router is too far from the first one and the signal is too weak.
Check the ethernet cable first—unplug it and plug it back in firmly. Then log into the second router's admin panel again and confirm that DHCP is set to Off. If both of those are correct and the problem persists, try moving the second router closer to the first one temporarily to see if distance is the issue.
If you find that the speed loss is too severe for your needs, or if you need reliable high-speed coverage in multiple rooms, it is time to replace this setup. A mesh WiFi system (like Eero, Netgear Orbi, or TP-Link Deco) is designed to handle this job better and will give you faster speeds throughout your home. A wireless access point is another option if you only need to extend coverage without adding a second network.
Frequently Asked Questions
Can I use WiFi instead of an ethernet cable to connect the two routers?
Yes, some routers support wireless bridging or WDS mode, which lets the second router connect to the first one over WiFi instead of ethernet. However, this cuts your bandwidth even more than ethernet does, because the router must use the same channel to receive and transmit. Ethernet is always better if you can run a cable.
Do both routers need to be the same brand?
No. You can mix brands—a Netgear modem with a TP-Link first router and a Linksys second router, for example. The only requirement is that both routers have standard ethernet ports and can be configured through a web browser or app. Matching brands sometimes makes configuration slightly easier, but it is not necessary.
Will this setup work with a cable modem and a fiber modem?
Yes. The type of modem does not matter. As long as the modem has an ethernet port and your routers have WAN ports, you can connect them the same way. The modem straightforward passes the internet signal to the first router, regardless of how it receives that signal from your service provider.
What if I want both routers to use the same wireless network name?
You can set both routers to broadcast the same SSID and password, and devices will switch between them as you move around. However, this can cause problems: devices sometimes get stuck on the weaker router and do not switch automatically. Most people find it easier to give each router a different name and switch manually when needed.
Can I add a third router to this setup?
Technically yes, but the speed loss becomes severe. Each additional router in the chain cuts bandwidth further. If you need coverage in three or more locations, a mesh system is a much better choice than daisy-chaining multiple traditional routers.