A yellow blinking light means your modem is trying to connect to the internet but hasn't succeeded yet
When your Xfinity modem blinks yellow, it is stuck between "powered on" and "connected." The modem has power and is running its startup sequence, but it cannot reach Comcast's network. This usually lasts a few minutes during a normal restart. If it keeps blinking yellow for more than 10 minutes, something is blocking the connection — either on your end or on Comcast's side.
The yellow light is not a failure yet. It is a "waiting" state. Your modem is doing what it should do; it just needs to finish. The problem is figuring out whether to wait longer or take action.
Key Takeaways
- Yellow blinking for the first few minutes after power-up is normal and requires no action.
- If yellow blinking continues past 10 minutes, restart the modem by unplugging it for 30 seconds, then plugging it back in.
- Check that the coaxial cable (the thick cable from the wall) is hand-tight at both the modem and the wall outlet.
- If the light stays yellow after a restart and cable check, contact Comcast to confirm the line is active and there is no outage in your area.
When yellow blinking is normal
Yellow blinking happens every time your modem powers on or restarts. During this time, the modem is loading its firmware, checking its memory, and sending signals down the coaxial cable to Comcast's network. This process usually takes 2 to 5 minutes. If your modem blinks yellow for that long and then turns solid white or blue, the connection worked and you can ignore it.
You will also see yellow blinking if you unplug the modem and plug it back in, or if there is a brief power outage. Again, this is normal. Wait 10 minutes before assuming something is wrong.
How to restart your modem
If the yellow light has been blinking for more than 10 minutes, restart the modem. Unplug the power cable from the back of the modem — not from the wall outlet, but from the modem itself. Wait 30 seconds. Plug it back in. The lights will go dark, then start blinking again. Watch for the yellow light to change to white or blue within 5 to 10 minutes.
While you wait for the restart, do not unplug anything else. Leave the coaxial cable connected. The modem needs that cable to talk to Comcast's network.
Check the coaxial cable connection
The thick cable that runs from the wall outlet to your modem is called a coaxial cable. If it is loose, the modem cannot reach the network, and the yellow light will keep blinking. Grab the cable where it screws into the back of the modem and turn it clockwise by hand until it is snug. Do not use a wrench or pliers — hand-tight is enough. Then check the other end of the cable where it connects to the wall outlet and tighten that the same way.
Loose cables are one of the most common reasons for a stuck yellow light. Many people do not realize the connections can loosen over time, especially if the modem gets bumped or moved.
What to do if yellow blinking continues
After you restart the modem and check both cable connections, give it another 10 minutes. If the light is still blinking yellow, the problem is likely on Comcast's end. Contact Comcast customer service at 1-800-934-6489 or through the Xfinity app. Tell them your modem is stuck on a yellow blinking light. They will check whether your account is active, whether there is an outage in your area, and whether the line itself is working.
Comcast can also send a signal to your modem remotely to force it to reconnect. Sometimes this works when ready. If it does not, they may schedule a technician visit or replace the modem under warranty.
Other lights and what they mean
Your Xfinity modem has several lights, and each one tells you something different. A solid white or blue light means the modem is connected and working. A red light means there is a serious problem — usually no signal from the wall or a hardware failure. A light that is off means the modem has no power. Yellow blinking is the middle ground: the modem is trying but not there yet.
If you see a red light instead of yellow, skip the restart and call Comcast right away. Red means the modem cannot connect at all, and a restart usually will not fix it.
When to replace your modem
If your modem stays on yellow blinking even after Comcast confirms the line is active and there is no outage, the modem itself may be failing. Modems typically last 5 to 7 years. If yours is older than that and keeps getting stuck on yellow, replacement is usually the next step. Comcast will often replace a modem under warranty or for a small fee if it is out of warranty.
Before you pay for a replacement, ask Comcast whether they have already sent a replacement modem to your address. Sometimes they ship a new one automatically when they detect a problem, and it arrives within a few days.
Frequently Asked Questions
How long should I wait before I restart the modem?
Wait at least 10 minutes. The modem needs time to complete its startup sequence. If it is still blinking yellow after 10 minutes, then restart it. Restarting too early can interrupt the process and make it take longer.
Does yellow blinking mean I have no internet?
Yes, while the light is blinking yellow, you do not have internet. Once it turns solid white or blue, the connection is live. If you need internet urgently and the yellow light has been on for more than 10 minutes, restart the modem and call Comcast while you wait.
Can I fix this without calling Comcast?
Often yes. Restart the modem and check both cable connections. If the light turns solid after that, the problem is solved. If it stays yellow after a restart and cable check, you will need Comcast to investigate the line or account.
What if the yellow light blinks, then turns red?
Red means the modem cannot connect to the network at all. This usually means the line is down, the account is inactive, or the modem has a hardware failure. Call Comcast when ready rather than waiting.
Is it safe to unplug the modem while it is blinking yellow?
Yes, it is safe. Unplugging during yellow blinking will not damage the modem. However, it will interrupt the connection attempt, so you will have to wait for the startup sequence to run again after you plug it back in.