Start with the basic outline shape
A PlayStation controller has a rounded rectangular body with two curved handles at the bottom. Begin by drawing a horizontal rectangle in the center of your page — make it wider than it is tall, roughly the size of your palm. Round all four corners so it looks smooth, not sharp.
Next, draw two curved lines extending downward from the bottom left and bottom right of that rectangle. These become the grip handles. Curve them outward slightly, then bring them back inward at the bottom so they look like two hands holding something. The handles should be narrower than the main body and taper as they go down.
Connect the bottom of each handle with a short curved line to close the shape. You now have the basic silhouette — a rounded rectangle with two handles underneath. This frame is your foundation for everything else.
Key Takeaways
- The controller body is a rounded rectangle with two curved handles extending downward, and all corners should be smooth rather than sharp.
- The touchpad sits in the center-top area and is a large rectangular shape, slightly wider than it is tall.
- Four buttons arranged in a diamond pattern go on the right side of the controller, with the triangle at the top, X at the bottom, square on the left, and circle on the right.
- The shoulder buttons (L1, L2, R1, R2) sit along the top edges, with two on each side, and the analog sticks go in the lower corners of the main body.
- Add shading and shadows under the handles and around the edges to make the flat drawing look three-dimensional.
Draw the touchpad in the center
The touchpad is the large dark rectangle that dominates the top half of a PlayStation controller. Position it roughly in the center of your rounded rectangle body, leaving space above it for the speaker and indicator lights. Make it wider than it is tall — about two-thirds the width of the main body.
Round the corners of the touchpad slightly, but less than the outer body. Draw a thin border around it to show the edge. Inside, you can add a subtle horizontal line or two to suggest the touch-sensitive surface, but keep it minimal — the touchpad should look flat and dark, not busy.
Place the four action buttons on the right side
PlayStation controllers have four colored buttons arranged in a diamond shape on the right side of the body. Start by finding the right half of your controller outline, below and to the right of the touchpad. Draw four circles or slightly flattened circles arranged in a diamond — one at the top (triangle), one at the bottom (X), one on the left (square), and one on the right (circle).
Space them evenly so they form a clear diamond pattern. Each button should be roughly the same size, about the size of a dime or smaller. Once you have the circles in place, add the symbols inside: a triangle pointing upward in the top button, an X in the bottom button, a square in the left button, and a circle in the right button. These symbols are the PlayStation button icons.
Add the shoulder buttons along the top edges
The shoulder buttons run along the top edge of the controller, two on the left side and two on the right. On the left edge, draw two small rounded rectangles stacked vertically — these are L1 (the upper one) and L2 (the lower one). Do the same on the right edge for R1 and R2. Make them small and slightly raised, as if they sit on top of the controller edge.
You can add small labels or just leave them as shapes. The L and R buttons are typically smaller and flatter than the action buttons, so keep them proportionally smaller in your drawing. They should look like they could be pressed down, not like full circles.
Draw the analog sticks in the lower corners
PlayStation controllers have two analog sticks positioned in the lower left and lower right areas of the main body, above where the handles begin. Draw two circles in these positions — one in the lower left corner and one in the lower right corner. Make them smaller than the action buttons, roughly the size of a pencil eraser.
Inside each circle, draw a smaller circle or dot in the center to represent the stick's top. You can add a slight depression or shadow around the edge of each stick to show that it sits slightly recessed into the controller body. These sticks should look like they can move in all directions.
Add details like the speaker and indicator lights
Above the touchpad, in the center-top area, draw a small rectangular speaker grille. This is just a series of thin horizontal lines close together, creating a striped pattern. Keep it small and subtle — it should not compete with the touchpad or buttons.
To the left and right of the speaker, add small indicator lights. These are typically tiny circles or dots that show the controller's status. You can leave them as straightforward dots or add a small glow around them. The speaker and lights are small details, but they make the controller look more complete and recognizable.
Shade and add dimension with shadows
To make your flat drawing look three-dimensional, add shading along the edges and under the handles. Lightly shade the underside of the handles with a pencil or marker — this creates shadow and makes them appear to curve away from the viewer. Add a subtle shadow along the bottom edge of the main body where it meets the handles.
Shade the edges of the touchpad slightly darker than the center to show depth. Around each button, add a tiny shadow on one side to make them look raised and pressable. The goal is not heavy shading but enough to suggest form and depth. Use a light hand — too much shadow will make the drawing look muddy.
You can also add a thin highlight line along the top edge of the controller body to suggest light reflecting off the plastic surface. This small detail makes the whole drawing feel more realistic and polished.
Frequently Asked Questions
What's the easiest way to get the proportions right?
Start by drawing a rectangle and dividing it into thirds horizontally. The touchpad occupies the upper two-thirds, and the buttons and sticks fill the lower third. This straightforward division helps you place everything in the right spot without measuring. You can erase the guide lines once everything is positioned.
Should I use a ruler for the straight edges?
A ruler helps with the main body outline and the touchpad border, but the handles and buttons look better if they are slightly freehand. The controller is not perfectly geometric — slight imperfections make it look more natural. Use a ruler for the big shapes, then draw the smaller details by hand.
How do I make the buttons look like they're actually on the controller?
Add a small shadow or darker line on one side of each button circle, as if light is hitting it from above. This makes the button appear to sit on the surface rather than float. A tiny highlight on the opposite side reinforces the effect. Even a subtle shadow makes a huge difference.
Can I color my drawing, and what colors should I use?
Yes. PlayStation controllers come in black, white, and various colors. The body is usually matte plastic, so use a solid, flat color. The touchpad is dark gray or black. The action buttons are typically white, black, red, and blue (or all one color depending on the controller model). The handles are the same color as the body. Keep colors straightforward and flat for a clean look.
What if my controller doesn't look quite right?
The most common issue is making the handles too thin or too short. They should be substantial and curve outward noticeably. Also, check that your four action buttons form a clear diamond — if they are too close together or uneven, the whole controller looks off. Step back and compare your drawing to a real controller or a photo to spot what needs adjusting.