Two ways to reset a PS4 controller
A PS4 controller can be reset in two ways: a soft reset that clears temporary problems without erasing your settings, and a hard reset that returns the controller to factory defaults. A soft reset fixes most issues — unresponsive buttons, drift, or connection drops — and takes 30 seconds. A hard reset erases all pairing data and is only necessary if the controller will not connect to your console at all, or if you are selling or giving away the controller.
The soft reset is your first step for any controller problem. The hard reset is a last resort because you will have to pair the controller to your PS4 again afterward, which requires a USB cable.
Key Takeaways
- A soft reset — holding the power button for 30 seconds — fixes most controller problems and keeps all your settings intact.
- A hard reset requires a small pin or paperclip to press the reset button on the back of the controller, then reconnecting it to your PS4 with a USB cable.
- Soft reset first; only do a hard reset if the controller will not connect to your console at all.
- After a hard reset, you must pair the controller again using a USB cable before you can use it wirelessly.
Soft reset: power button method
Turn off your PS4 completely — do not put it in rest mode. Press and hold the power button on the controller for 30 seconds. The light on the controller will flash, then turn off. Wait 10 seconds, then press the power button once to turn the controller back on. The light will return and the controller should reconnect to your console.
This reset clears the controller's temporary memory without changing any settings or pairing information. It works for button lag, stick drift that comes and goes, or a controller that drops connection during play. If the problem returns after a few hours or days, the issue may be physical wear rather than a software glitch.
Hard reset: using the reset button
Locate the small reset button on the back of the controller, in the recessed area between the L2 and R2 buttons. You will need a straightened paperclip, a small pin, or a SIM card ejector tool to press it — the button is too small for a fingernail. Press and hold the reset button for three to five seconds. The light on the controller will turn off.
After the hard reset, the controller has no pairing data and will not connect wirelessly to your PS4. You must use a USB cable to reconnect it. Plug a micro-USB cable into the controller and the other end into your PS4. The light will turn blue. Press the PS button on the controller. Your PS4 will recognize it and pair it again. Once paired, you can unplug the cable and use the controller wirelessly as normal.
When to soft reset versus hard reset
Use a soft reset if the controller turns on, connects to your PS4, but has a problem during play — buttons feel unresponsive, the stick drifts, or the connection cuts out. A soft reset solves most of these issues because they are usually temporary glitches in the controller's memory, not hardware failure.
Use a hard reset only if the controller will not turn on, will not connect to your PS4 even with a cable, or if you are preparing to sell or give away the controller. A hard reset is also worth trying if you have already done a soft reset and the problem persists, though that usually means the controller has a hardware problem that a reset cannot fix.
Troubleshooting after a reset
If a soft reset does not fix the problem, try charging the controller for at least two hours. A low battery can cause connection drops and unresponsive buttons. Connect it to your PS4 with a USB cable while it charges — the light will turn orange, then white when fully charged.
If the controller still does not work after charging, try a hard reset. If a hard reset does not work either, the controller likely has a hardware problem. Stick drift, for example, is caused by wear inside the joystick mechanism and cannot be fixed by resetting. In that case, you may need to repair or replace the controller.
Pairing a controller after a hard reset
After a hard reset, the controller has no memory of your PS4. Plug a micro-USB cable into the controller and into your PS4 — any USB port on the console works. Press the PS button on the controller. Your PS4 will recognize it as a new controller and pair it automatically. This takes about 10 seconds.
Once paired, unplug the cable. The controller will now connect wirelessly to your PS4 the next time you press the PS button, just as it did before the reset. You do not have to pair it again unless you do another hard reset or pair it to a different PS4.
Frequently Asked Questions
Will a soft reset erase my game saves or controller settings?
No. A soft reset only clears the controller's temporary memory. Your game saves stay on your PS4, and any custom button assignments or vibration settings on the controller remain unchanged.
Do I need a USB cable for a soft reset?
No. A soft reset uses only the power button and takes 30 seconds. You do not need any cables or tools.
What if the reset button is stuck or will not press?
Try a different tool — a straightened paperclip often works better than a pin. If the button still will not press, do not force it. The button may be damaged, and forcing it could break the controller further. A soft reset may still solve your problem without needing the hard reset.
Can I reset a controller while it is connected to my PS4?
Yes. You can do a soft reset while the controller is connected and your PS4 is on. For a hard reset, turn off your PS4 first, then press the reset button on the back of the controller.
How long does pairing take after a hard reset?
Pairing usually takes 10 to 15 seconds. Plug in the USB cable, press the PS button, and wait. Your PS4 will display a message when the controller is paired. You can then unplug the cable.