Reset Your Controller Using the Physical Reset Button
The fastest way to reset a PlayStation controller is to use the small reset button on the back. This button clears the controller's memory and disconnects it from any paired device, which solves most connection problems and unresponsive button issues.
Locate the reset button on the back of your controller, near the left shoulder button. You will see a small recessed hole — this is the reset button. Use a straightened paperclip, a thin pin, or the tip of a ballpoint pen to press and hold the button for three to five seconds. You should feel a slight click when the button engages. Release the button and wait ten seconds before trying to connect the controller again.
After the reset, your controller will no longer be paired with any console or device. You will need to reconnect it using a USB cable or by re-pairing it wirelessly through your console's settings menu. This method works for PlayStation 4 and PlayStation 5 controllers.
Key Takeaways
- The physical reset button on the back of your controller clears all pairings and settings in seconds without needing a console.
- Use a paperclip or thin pin to press the recessed reset button for three to five seconds until you feel a click.
- After a physical reset, you must reconnect the controller to your console using a USB cable or wireless pairing.
- If the physical reset does not fix your problem, try updating your controller's firmware through your console's settings.
- A full factory reset through your console will erase all saved data, so use it only after other methods have failed.
Reconnect Your Controller After a Physical Reset
Once you have pressed the reset button, your controller is no longer paired with your console. The next step depends on whether you want to use a wired or wireless connection.
For a wired connection, plug a USB-C cable (PlayStation 5) or USB micro cable (PlayStation 4) into the controller and into an available USB port on your console. The console will recognize the controller within a few seconds. You can then use it while plugged in, or unplug it to use it wirelessly after the console has registered it.
For a wireless connection, go to your console's Settings menu, then select Devices, then Controllers, then Bluetooth Devices. Put your controller into pairing mode by holding the PlayStation button and the Share button together for three seconds until the light bar flashes. Your console will detect the controller and add it to the list of available devices. Select it to complete the pairing.
Update Your Controller's Firmware
If your controller is still not responding after a physical reset, the problem may be outdated firmware. Firmware is the software that runs inside your controller, and updates can fix bugs that cause connection drops or button lag.
Connect your controller to your console using a USB cable. Go to Settings, then Devices, then Controllers, then Firmware Update. Your console will check for available updates and install them automatically. This process usually takes two to five minutes. Do not unplug the controller or turn off the console during the update.
After the update finishes, disconnect the USB cable and test your controller. Many connection and responsiveness issues resolve after a firmware update, even if the physical reset did not fix them.
Perform a Full Factory Reset Through Your Console
A full factory reset through your console's settings will erase all custom button assignments, vibration settings, and any other changes you have made to that controller. Use this method only if the physical reset and firmware update have not solved your problem.
Go to Settings, then Devices, then Controllers, then select the controller you want to reset. Choose the option to reset or restore defaults. Your console will ask you to confirm — this action cannot be undone. After you confirm, the controller will return to its original factory settings.
This reset is different from the physical reset button because it erases settings stored on your console rather than on the controller itself. If you have customized button layouts or vibration intensity for specific games, you will need to set those up again after a factory reset.
Common Reasons Your Controller Stops Responding
Controller problems usually fall into a few categories. Connection issues happen when the controller loses its wireless signal or fails to pair with the console — these are solved by the physical reset or by re-pairing. Button lag or unresponsive buttons occur when the controller's firmware is outdated or when dirt has built up under the buttons — firmware updates and physical resets fix most of these.
Stick drift, where the analog stick registers movement even when you are not touching it, is a hardware problem that a reset cannot fix. If stick drift persists after a reset and firmware update, the controller's internal sensors need replacement. Battery problems show up as the controller losing power quickly or not charging at all — if your controller will not hold a charge after a full reset, the battery itself may be failing.
If your controller works fine when plugged in but loses connection when unplugged, the problem is usually the wireless receiver or battery, not the controller's software. A physical reset will not solve this, but a firmware update might improve the connection quality.
Prevent Future Connection Problems
Keep your controller firmware up to date by checking for updates once a month. Go to Settings, Devices, Controllers, and Firmware Update — your console will tell you if an update is available. Regular updates prevent many connection and responsiveness issues before they start.
Store your controller in a cool, dry place away from direct sunlight. Heat and moisture can damage the internal components and battery. Avoid dropping your controller or explore pressure to the buttons and sticks, as physical damage can cause drift and unresponsive buttons that no reset will fix.
If you use your controller wirelessly, keep it within 20 feet of your console and away from other wireless devices like routers or cordless phones. Interference from these devices can cause connection drops that feel like a hardware failure but are actually just signal problems.
Frequently Asked Questions
Will resetting my controller erase my game saves?
No. A controller reset only affects the controller itself and its connection to your console. Your game saves are stored on your console's hard drive or in cloud storage, and they will not be touched by any controller reset.
How do I know if the reset button actually worked?
After you press the reset button, the light bar on the front of the controller will turn off or dim. If the light bar does not change, try pressing the button again — you may not have pressed hard enough or hit the exact center of the button.
Can I reset my controller without a console?
Yes. The physical reset button works without a console — you can press it anytime to clear the controller's pairings and settings. However, you will need a console or a computer with Bluetooth to reconnect the controller after the reset.
What if my controller still does not work after I reset it?
Try a firmware update next, as that fixes many problems the physical reset cannot. If the controller still does not respond after a firmware update, the problem is likely a hardware failure inside the controller, and you may need to replace it.
Do I need to reset both controllers if I have two?
Only reset the controller that is having problems. Resetting both controllers will disconnect both from your console, and you will need to pair them again. If only one controller is unresponsive, leave the other one alone.