You can connect a projector to a TV, but it usually means using the TV as a second display, not replacing it

A projector and a TV serve different purposes, so connecting them together is not a standard setup. What you are most likely trying to do is one of three things: use your TV to control what the projector shows, mirror your TV's picture onto a wall via the projector, or send a projector's output to a TV screen instead of a wall. Each route uses different cables and settings.

The simplest connection is HDMI from a single source to both devices. If you have a streaming device, game console, or laptop, you can run one HDMI cable to the projector and another to the TV from the same device. Both will show the same picture at the same time. This does not require the projector and TV to talk to each other — they both just receive the signal independently.

If you want the TV to control the projector's input or settings, you will need to check whether your projector supports CEC (Consumer Electronics Control) over HDMI. CEC allows devices on the same HDMI network to communicate. Not all projectors have this feature, so check your projector's manual before assuming it does.

Key Takeaways

  • A projector and TV do not need to be directly connected to each other; they both receive video from a separate source like a streaming device or laptop.
  • HDMI is the standard cable for both devices, and you will need separate HDMI cables running from your source to each one.
  • CEC over HDMI allows some projectors and TVs to communicate and control each other, but not all models support it.
  • If your projector has no HDMI input, you may need an adapter for older connection types like VGA or composite video.
  • The TV and projector will work independently; turning one off does not affect the other.

Setting up HDMI connections from a single source

Start by identifying your video source — this is the device sending the picture, such as a Roku, Apple TV, PlayStation, Xbox, or laptop. Locate its HDMI output port. Most modern sources have at least one; some have two or more.

Run one HDMI cable from the source's HDMI output to the projector's HDMI input. Run a second HDMI cable from the same source to the TV's HDMI input. Both cables should be the same type (HDMI 2.0 or higher works for most content). Power on the source first, then the projector and TV. Both devices should display the same picture without any additional setup.

If only one picture appears, check that both devices are set to the correct input. On the TV, press the Input or Source button on the remote and select the HDMI port you plugged into. On the projector, use its remote or menu button to select the same HDMI input. Some projectors default to the first HDMI port; others require manual selection.

Connecting a projector to a TV using CEC (if supported)

CEC is a feature that lets HDMI devices communicate over the same cable. If both your projector and TV support CEC, you can control one device from the other's remote in some cases. Check your projector's manual for "CEC," "HDMI-CEC," "Anynet+," "Aquos Link," or similar terms — manufacturers use different names.

To enable CEC, connect both devices to the same HDMI source using separate cables (as described above). Then go into each device's settings menu and look for a CEC or HDMI control option. Enable it on both. The exact menu path varies by brand — for example, on some LG TVs it is under Settings > General > HDMI-CEC, while on Sony projectors it may be under Setup > HDMI Control.

Once enabled, you may be able to use one remote to power both devices on or off, or to switch inputs on both at once. Not all projectors support full CEC control, so test your specific model to see what functions work. If CEC does not work after enabling it, check that you are using a high-quality HDMI cable rated for 2.0 or higher.

Using adapters for older projectors without HDMI

If your projector has only VGA, DVI, or composite video inputs (common on older models), you will need an adapter to connect it to a modern source. A VGA-to-HDMI adapter or DVI-to-HDMI adapter converts the digital HDMI signal to the older standard. These adapters are inexpensive and widely available online.

Connect the HDMI cable from your source to the adapter, then connect the adapter's output (VGA or DVI) to the projector. The TV still connects directly via HDMI to the source. Both devices will display the same picture, though the projector may have slightly lower image quality depending on the adapter's build and the cable length.

For very old projectors with only composite video (three RCA plugs — red, white, yellow), you will need a composite-to-HDMI converter, which is bulkier and more expensive. These are less common and harder to find; if your projector is that old, it may be worth checking whether a newer model would serve you better.

Troubleshooting when one device does not show a picture

If the TV displays a picture but the projector does not, first check that the projector is powered on and that its lamp is warm (this takes 30 seconds to a minute on most models). Then press the projector's Input or Source button and cycle through the available HDMI ports until you see the picture. Some projectors default to a port that is not in use.

If the projector still shows nothing, try a different HDMI cable. Faulty cables are common and can prevent a signal from reaching the device. Swap the cable between the TV and projector temporarily — if the TV then loses picture and the projector gains it, the cable was the problem.

If both devices are connected but one is black or shows "No Signal," the source device may not be outputting to both HDMI ports at once. Check your source's display settings. On a laptop, press Windows Key + P (Windows) or use System Preferences > Displays (Mac) to enable extended display or mirror mode. On a streaming device or game console, go to Settings > Display and confirm that both HDMI outputs are active if that option exists.

Choosing the right HDMI cables and ports

Use HDMI 2.0 cables or higher for the best reliability. Older HDMI 1.4 cables work for standard video but may drop signal on longer runs (over 25 feet). If your cables are longer than 15 feet, buy cables rated for high-speed use to avoid picture dropout.

Check that your source device has enough HDMI outputs for both the projector and TV. If it has only one HDMI port, you have two options: use an HDMI splitter (a small device that sends one HDMI signal to two outputs), or switch cables manually between the two devices. HDMI splitters are cheap but can sometimes cause compatibility issues with certain projectors, so test before buying.

Label your cables with tape or a marker so you know which one goes where. This saves time if you need to troubleshoot or rearrange your setup later.

When to use a projector and TV together versus separately

Running both a projector and TV from the same source makes sense if you want to watch on a large wall display while also having a smaller screen visible — for example, showing a presentation on the wall while monitoring a control panel on the TV. It also works if you are in a room where the projector and TV serve different purposes at different times.

If you are trying to choose between a projector and a TV for everyday viewing, they are not interchangeable. Projectors work best in dark rooms and produce a larger image but require a blank wall or screen. TVs work in any lighting and take up less space but show a smaller picture. Connecting them together does not change these trade-offs; it just lets you use both at once.

Frequently Asked Questions

Can I connect a projector directly to a TV without another device?

No. A projector and TV are both display devices — neither one sends video to the other. You need a third device (a streaming box, laptop, game console, or cable box) that outputs video to both. The projector and TV receive the signal independently from that source.

Will connecting a projector to a TV through HDMI damage either device?

No. HDMI is a standard connection designed to handle multiple devices on the same cable. As long as you use the correct cable type and do not force the connectors, both devices will work safely. Faulty cables can cause signal loss but not hardware damage.

What if my projector and TV have different HDMI versions?

It does not matter. HDMI versions are backward compatible, so an older TV will work fine with a newer projector or vice versa. Use HDMI 2.0 cables to may support both devices receive a strong signal, and you will have no problems.

Can I use a projector as a second monitor for my TV?

No. A projector is a display, not a source. It cannot receive a signal from a TV. However, you can connect both your projector and TV to the same computer, and then use your computer's display settings to show different content on each screen.

Do I need a special cable to connect a projector to a TV?

No. Standard HDMI cables work for both devices. If your projector is older and lacks HDMI, you will need an adapter (VGA-to-HDMI or DVI-to-HDMI), but the TV still uses a regular HDMI cable.