The three ways to add sound to your projector
Most projectors have a built-in speaker, but it is usually small and tinny. To get better sound, you connect an external speaker using one of three methods: an audio cable plugged into the projector's audio output jack, a wireless connection via Bluetooth, or an HDMI cable that carries both picture and sound together.
Which method works depends on what ports your projector has and what speaker you own. The easiest route is usually whatever your projector and speaker both support — if your projector has Bluetooth, a wireless speaker saves you cable clutter. If your projector only has an audio jack, a wired speaker is your only choice.
Before you buy a speaker or start plugging things in, check your projector's manual or the back panel to see which ports it actually has. This takes two minutes and saves you from buying equipment that won't work.
Key Takeaways
- A 3.5 mm audio cable (the same size as headphone jacks) is the most common wired connection and works with almost any projector and speaker.
- Bluetooth wireless connection requires both your projector and speaker to have Bluetooth built in, and you pair them the same way you would pair a phone to a speaker.
- HDMI cables carry both picture and sound, so if your projector has HDMI input, you can run sound through the same cable as video from your source device.
- Check your projector's manual or back panel before buying a speaker to confirm which connection types your specific model supports.
- If your projector has no audio output at all, you will need to run sound from your video source device directly to the speaker instead.
Wired connection using a 3.5 mm audio cable
A 3.5 mm audio cable (also called a mini-jack or headphone cable) is the simplest and most reliable way to connect a speaker to a projector. One end plugs into the projector's audio output jack, and the other end plugs into the speaker's audio input jack. Both jacks look like small round holes, usually labeled "audio out" or "line out" on the projector and "audio in" or "line in" on the speaker.
You can buy a 3.5 mm cable at any electronics store or online for a few dollars. The length you need depends on how far your speaker will sit from the projector — measure the distance before you buy. If your speaker is across the room, a 25-foot cable is common and still affordable.
Once the cable is plugged in, turn on both the projector and the speaker. The projector should automatically detect the external speaker and route sound to it instead of the built-in speaker. If you hear nothing, check that the speaker is powered on and turned up to a reasonable volume, then check the projector's settings menu to make sure audio output is not muted or set to the internal speaker.
Bluetooth wireless connection
If your projector and speaker both have Bluetooth, you can skip the cable entirely. Bluetooth is a wireless standard that lets devices talk to each other over short distances — usually 30 feet or less, depending on the devices and any obstacles between them.
To connect via Bluetooth, turn on both the projector and the speaker, then put the speaker into pairing mode. The method varies by speaker — some have a dedicated Bluetooth button, others require you to hold the power button for a few seconds. Check the speaker's manual if you are unsure. Once the speaker is in pairing mode, go into the projector's settings menu (usually accessed via the remote control), find the Bluetooth section, and select the speaker's name from the list of available devices. The two will pair and stay connected as long as they are both powered on and in range.
Bluetooth is convenient because there are no cables to run, but it is only an option if your projector actually has Bluetooth built in. Many older projectors and some budget models do not. Check your projector's specifications before assuming it has Bluetooth.
HDMI connection for picture and sound together
If your video source (a streaming device, laptop, or media player) connects to the projector via HDMI, that same HDMI cable can carry sound as well as picture. This works because HDMI is a digital standard that handles both audio and video in one cable.
To use this method, plug the HDMI cable from your source device into the projector's HDMI input port. Then connect a speaker to the projector's audio output jack or via Bluetooth, just as you would with any other setup. The projector will receive sound from the HDMI cable and pass it to the external speaker.
Some projectors also have an HDMI audio output port (sometimes labeled "HDMI audio out" or "HDMI ARC"), which lets you send sound back out through an HDMI cable to a soundbar or receiver. This is less common on basic projectors but useful if you have a home theater system. Check your projector's manual to see if this port exists on your model.
When your projector has no audio output at all
A few projectors, especially very basic or very old models, have no audio output port of any kind. If this is your situation, you cannot connect a speaker directly to the projector. Instead, you run sound from your video source device to the speaker.
For example, if you are streaming from a laptop, plug a 3.5 mm audio cable from the laptop's headphone jack into the speaker's audio input. The laptop sends picture to the projector via HDMI and sound to the speaker via the audio cable. If you are using a streaming device like a Roku or Apple TV, check whether it has an audio output jack — many do, and you can run a cable from there to the speaker instead.
This setup is less elegant than connecting the speaker to the projector, but it works. The trade-off is that you have to manage two cables instead of one, and if you switch video sources, you may need to unplug and replug the audio cable.
Troubleshooting sound that is not working
If you have connected a speaker but hear no sound, work through these steps in order. First, make sure the speaker is powered on and the volume is turned up — this sounds obvious, but it is the most common cause. Second, check that the cable is fully plugged in on both ends, or that Bluetooth pairing is still active. Third, go into the projector's settings menu and confirm that audio output is not muted and is set to the external speaker, not the internal one.
If the projector's menu shows no audio output option, or if the speaker is not appearing in the Bluetooth list, the projector may not have audio output capability at all. Check the manual or the back panel again. If you are certain the cable is connected and the settings are correct, try a different audio cable or a different speaker to rule out a faulty cable or speaker.
If you are using HDMI and the projector receives picture but no sound, the issue is usually that the video source device is not sending audio through HDMI. Check the source device's audio settings — it may be set to send sound to the headphone jack instead. Some devices require you to explicitly enable HDMI audio output.
Choosing between wired and wireless
Wired connections are more reliable because they do not depend on wireless range or interference from other devices. A 3.5 mm cable will work every time you plug it in, with no pairing or connection steps. Wired speakers are also usually cheaper than wireless ones.
Wireless connections are more convenient because you do not have to run a cable across the room. Bluetooth is fast to set up once — you pair the speaker once, and it connects automatically every time you turn both devices on. Wireless is the better choice if your projector is mounted high on a wall or ceiling and running a cable would be difficult or ugly.
If your projector supports both, try wired first. If the cable is in the way or you find yourself unplugging and replugging it often, switch to Bluetooth. There is no wrong choice — it depends on your room and your preference.
Frequently Asked Questions
Can I use a Bluetooth speaker if my projector does not have Bluetooth?
No, not directly. Your projector and speaker both need Bluetooth to connect wirelessly. However, you can use a Bluetooth transmitter — a small device that plugs into the projector's audio output jack and broadcasts sound via Bluetooth to your speaker. This adds a step and a small cost, but it works if you want wireless sound without upgrading your projector.
What if my speaker only has RCA inputs, not a 3.5 mm jack?
You can buy a 3.5 mm to RCA adapter cable, which has a 3.5 mm plug on one end and two RCA plugs (red and white) on the other. Plug the 3.5 mm end into the projector and the RCA ends into the speaker. These adapters cost a few dollars and are widely available.
Will connecting a speaker to the projector disable the built-in speaker?
Usually yes. Once you plug in an external speaker, the projector automatically routes sound to it and mutes the internal speaker. If you want to switch back to the built-in speaker, unplug the external one or go into the projector's settings menu and change the audio output setting.
Can I connect multiple speakers to one projector?
Not directly through a single audio output jack. However, you can connect one powered speaker or receiver to the projector, and then connect additional speakers to that device. A receiver or powered speaker often has multiple audio outputs or can split the signal internally.
Do I need a special HDMI cable to carry sound?
No. Any standard HDMI cable carries both picture and sound — there is no difference between a "video HDMI" and an "audio HDMI." All HDMI cables are the same in this respect.