The three ways to add sound to your projector

A projector's built-in speaker is usually too quiet and tinny for anything longer than a short video. You have three real options: run an audio cable from the projector to powered speakers, connect wireless speakers via Bluetooth, or run audio through your projector's HDMI input from a separate device. Which one works depends on what ports your projector has, where you want the speakers to sit, and whether you already own speakers.

The simplest route for most people is a 3.5mm audio cable (the thin jack you see on headphones) plugged into the projector's audio-out port, connected to powered speakers that sit near the screen. If your projector has no audio-out port, HDMI is your backup—the audio travels inside the HDMI cable itself, and you split it off to speakers using a small converter box. Bluetooth works if your projector supports it, but not all do, and wireless speakers add another device to charge and troubleshoot.

Key Takeaways

  • Most projectors have a 3.5mm audio-out jack where you plug in a cable that runs to powered speakers, which is the cheapest and most reliable method.
  • If your projector has no audio-out port, you can extract audio from the HDMI cable using an HDMI audio extractor, a small box that costs $15 to $40.
  • Bluetooth speakers work if your projector has Bluetooth built in, but you should check your projector's manual first because many older and budget models do not.
  • Powered speakers (with a built-in amplifier) are required—passive speakers will not work without a separate amplifier.
  • Test the audio before you mount the projector or run cables behind walls, because some combinations of projectors and speakers have compatibility issues that only show up when you try them.

Using a 3.5mm audio cable and powered speakers

Look at the back or side of your projector for a port labeled "Audio Out," "Line Out," or "Headphone Out." It is a small round jack about the size of a pencil eraser. Plug one end of a 3.5mm audio cable into that port. The cable itself costs $5 to $15 depending on length—get one long enough to reach your speakers without stretching tight, usually 10 to 25 feet.

Plug the other end into the audio input on your powered speakers. Powered speakers have a built-in amplifier, so they do not need a separate receiver or amp. Look for an input labeled "Audio In," "Line In," or "Aux In." If your speakers have multiple inputs (RCA connectors, XLR, or 3.5mm), use the 3.5mm input to match your cable. Turn the volume dial on the speakers to about 25 percent before you start, then adjust up or down once the projector is playing.

If the projector's audio-out port is labeled "Headphone Out," the volume control on the projector itself will affect the speaker volume. If it says "Line Out," the projector's volume control may not work, and you will control volume only from the speaker's dial. Check your projector's manual to be sure. Some projectors have both ports—use "Line Out" if available, because it gives you a cleaner signal.

Extracting audio from HDMI when there is no audio-out port

Newer projectors sometimes skip the 3.5mm audio-out port to save cost. If your projector has no audio-out jack, the audio is still traveling through your HDMI cable—you just need to pull it out. You do this with an HDMI audio extractor, a small box that costs $15 to $40 and sits between your video source and the projector.

Unplug the HDMI cable that runs from your device (a laptop, streaming box, or Blu-ray player) to the projector. Plug that cable into the HDMI input on the audio extractor. Then run a new HDMI cable from the extractor's HDMI output to the projector. The extractor now has the audio separated out—plug a 3.5mm cable from the extractor's audio-out port into your powered speakers. The video goes to the projector, and the audio goes to the speakers.

The extractor does not need power in most cases—it draws power from the HDMI cable itself. If it has a USB port, plug that into a USB power adapter just to be safe. Test the setup before you hide the cables, because some extractors have trouble with certain HDMI versions or video formats. If you get no sound, try a different extractor model—they are cheap enough that swapping one out is faster than troubleshooting.

Connecting Bluetooth speakers to a projector

Not all projectors have Bluetooth. Check your projector's manual or the specifications sheet to confirm it lists "Bluetooth" or "Bluetooth audio." If it does, the process is straightforward: put your Bluetooth speakers in pairing mode (usually a button you hold for three seconds), then go into the projector's menu and select "Bluetooth" or "Wireless Audio." The projector will search for nearby devices and show your speakers' name. Select it, and the connection is done.

Bluetooth is convenient because you have no cables to run, but it adds complexity. The speakers need to be charged, they can drift out of range if you move them far from the projector, and some projectors have weak Bluetooth that cuts out if there is interference from WiFi or other wireless devices nearby. If you are setting up a permanent installation, a wired 3.5mm connection is more reliable. Bluetooth works better for portable setups where you move the projector between rooms.

One common mistake: people assume Bluetooth audio will work the same way as Bluetooth video. It does not. Your projector can receive video over HDMI and audio over Bluetooth at the same time, but if you are using an older projector that only has HDMI input, the audio may not separate from the HDMI signal automatically. In that case, you need the audio extractor method described above, even if you plan to use Bluetooth speakers.

Choosing the right speakers for your space

Powered speakers come in two main sizes: compact desktop models (4 to 8 inches wide) and larger floor-standing or bookshelf models (12 to 24 inches wide). For a small bedroom or office, a compact pair works fine. For a living room or basement, larger speakers will fill the space better and handle louder volumes without distortion. The wattage rating (usually 20 to 100 watts per speaker) matters less than you think—even 20 watts is loud enough for most rooms if the speakers are decent quality.

Look for speakers with a volume knob on the front or back, not just a remote control. A knob lets you adjust volume quickly without hunting for a remote. Check that the speakers have a 3.5mm input jack—some budget models only have Bluetooth or USB, which limits your options. If you are buying new speakers, brands like Edifier, Klipsch, and Audioengine make reliable powered speakers in the $50 to $200 range that work well with projectors.

Placement matters. Speakers sound best when they are at ear level and pointed toward where you sit, not hidden in a cabinet or pointed at a wall. If you are mounting the projector on the ceiling, put the speakers on a shelf or stand below the screen, angled slightly upward. Avoid putting speakers directly on the floor or in a corner, where bass gets muddy. A small speaker stand costs $20 to $40 and makes a noticeable difference.

Testing before you install

Before you mount the projector or run cables behind walls, plug everything in and test it with the projector sitting on a table. Play a video with dialogue and music—a movie trailer or YouTube video works fine. Listen for crackling, buzzing, or dropout. If you hear noise, try these fixes in order: lower the projector's volume to 75 percent, move the audio cable away from power cables (interference can cause buzzing), swap the audio cable for a different one, or try a different speaker input if your speakers have multiple options.

If the speakers have no sound at all, check that the cable is plugged all the way in—a loose connection is the most common cause. Then check the projector's audio settings. Some projectors default to internal speaker only, and you have to go into the menu and select "External Audio" or "Audio Out." The menu path varies by brand, but it is usually under "Audio," "Sound," or "Settings." Your projector's manual will tell you the exact steps.

Once everything works, you can hide the cables. Run the audio cable along the same path as the HDMI cable if possible, and use cable clips or conduit to keep it organized. If you are running cables through walls, use in-wall rated cable (marked CL2 or CL3), which is safer and meets electrical codes.

Troubleshooting common problems

If you have sound from the projector's internal speaker but not from the external speakers, the projector may not be set to output audio. Go into the projector's menu, find the audio settings, and look for an option that says "Audio Output," "Speaker," or "Output Device." Select "External" or "Line Out" instead of "Internal." Some projectors require you to physically disable the internal speaker before external audio works—check the manual if you cannot find the setting.

If the speakers are connected but very quiet, check the volume on both the projector and the speakers. The projector's volume should be at 75 to 100 percent, and the speaker's volume dial should be at 50 to 75 percent. If it is still quiet, the audio cable may be plugged into the wrong input on the speakers—some speakers have separate inputs for different devices, and you may have plugged into a muted or inactive input. Try each input one at a time.

If you hear crackling or buzzing, the audio cable is probably picking up electrical interference. Move the audio cable at least 6 inches away from power cables, HDMI cables, and the projector itself. If that does not help, replace the audio cable with a shielded one (marked "shielded" on the package), which costs a few dollars more but blocks interference. Crackling can also mean the volume is too high—lower it by 10 percent and see if it clears up.

Frequently Asked Questions

Can I use regular passive speakers instead of powered speakers?

No. Passive speakers have no built-in amplifier, so they need a separate receiver or amplifier to work. A projector's audio output is too weak to drive passive speakers on its own. You must use powered speakers, which have an amplifier built in. If you already own passive speakers, you would need to buy a separate amplifier, which costs more than just buying powered speakers.

What if my projector has no audio port at all?

Use an HDMI audio extractor as described in the section above. The extractor pulls the audio out of the HDMI signal and sends it to your speakers. This is the standard solution for projectors without a dedicated audio-out port, and it costs $15 to $40. Make sure the extractor supports the HDMI version your projector uses—most modern extractors work with HDMI 2.0 and newer.

Do I need to buy expensive speakers to get good sound?

No. A $60 to $100 pair of powered speakers will sound significantly better than the projector's internal speaker and is plenty for most rooms. Spending more gets you louder volume, deeper bass, and better build quality, but the jump from internal speaker to any decent external speaker is the biggest improvement. Test speakers in person if you can, or buy from a retailer with a return policy so you can send them back if they do not sound right in your space.

Can I connect multiple speakers to one projector?

Yes, but it depends on your setup. If you are using a 3.5mm audio cable, you can plug it into a powered speaker that has a second audio output, then run a cable from that output to a second speaker. Some powered speakers are designed as a pair and come with this built in. If you are using Bluetooth, most projectors can only connect to one Bluetooth speaker at a time, though some newer models support multiple devices—check your manual.

Will the audio cable interfere with the video signal?

No. Audio and video travel on separate cables and do not interfere with each other. You can run the audio cable right next to the HDMI cable without any problem. However, audio cables can pick up interference from power cables (the thick cables that carry electricity), so keep audio cables at least 6 inches away from those. This is a general best practice for any audio setup, not specific to projectors.