What a limit switch does and why it stops working
A limit switch on a motorized projector screen tells the motor when to stop rolling the screen up or down. It's a small mechanical switch mounted inside the tube that the screen fabric winds around. When the screen reaches the top or bottom position, a cam (a rotating piece attached to the motor shaft) pushes the switch, cutting power to the motor so the screen doesn't tear or jam.
The limit switch fails when the cam no longer lines up with the switch. This happens because the cam has shifted on the motor shaft, the switch bracket has bent or loosened, or the switch itself has worn out electrically. When calibration is off, the screen either stops before it reaches the end, stops after it should have, or doesn't stop at all.
You can fix most limit switch problems by repositioning the cam so it hits the switch at exactly the right moment. This is called calibrating the limit switch. If the switch itself is broken, you'll need to replace it.
Key Takeaways
- The limit switch stops your screen at the top and bottom by detecting a rotating cam on the motor shaft; when they don't line up, the screen won't stop properly.
- Most calibration problems can be fixed by loosening the cam set screw and rotating it until it hits the switch at the correct position, then tightening it again.
- You must disconnect power to the screen motor before opening the tube or adjusting any internal parts.
- If the switch itself is cracked, burned, or won't click when the cam touches it, the switch needs to be replaced rather than recalibrated.
- Calibration requires access to the inside of the motor tube, which means removing the screen fabric or opening an access panel — check your screen's manual for the correct method.
Disconnect power before you start
Before you touch anything inside the screen tube, turn off power at the wall outlet or breaker. Many motorized screens have a capacitor that holds an electrical charge even when the power switch is off. Touching live wires or capacitors can cause serious injury.
If your screen is hardwired to a wall switch or control panel, flip the breaker that controls it. If it plugs into an outlet, unplug it completely. Wait at least one minute to allow any stored charge to drain. Test the motor by pressing the up or down button — it should not move.
Access the motor tube and locate the cam and switch
The motor tube runs horizontally inside the rolled-up screen. To reach the limit switch and cam, you need to open the tube. The method depends on your screen model: some have a removable end cap, some have an access panel on the side, and some require you to partially unroll the screen fabric.
Check your screen's manual or the manufacturer's website for the correct access method. If you cannot find the manual, look for a model number on the motor housing or the screen's aluminum frame, then search the manufacturer's website. Do not force open any panels — you may crack the aluminum or damage the motor.
Once the tube is open, you will see the motor shaft running through the center. The cam is a small, off-center wheel or lobe attached to the shaft. The limit switch is a small lever or button mounted on a bracket near the cam's path. The switch should click when the cam pushes it.
Check whether the switch itself is broken
Before you adjust the cam, test the switch. Have someone press and hold the up button while you watch the cam rotate toward the switch. The switch lever should move when the cam touches it, and you should hear or feel a click. If the switch does not move or click, the switch is likely broken and needs to be replaced.
Also look for visible damage: a cracked plastic body, a burned or blackened contact point, or a lever that is bent or stuck. Any of these signs mean the switch should be replaced rather than recalibrated. Replacement switches are available from the screen manufacturer and typically cost between $30 and $80 plus shipping.
If the switch clicks and moves freely, the problem is calibration. Proceed to the next step.
Loosen the cam and rotate it to the correct position
The cam is held to the motor shaft by a single set screw, usually a small hex bolt or Phillips screw. Loosen this screw with the appropriate wrench or screwdriver — do not remove it completely, just loosen it enough that the cam can rotate on the shaft.
Manually rotate the motor shaft by hand (or have someone press the up or down button very briefly to move it a small amount). Position the cam so that it is just about to touch the switch lever, but not quite. The switch should be on the verge of clicking but not yet depressed.
Once the cam is in the correct position, tighten the set screw firmly. Do not overtighten — you only need enough pressure to keep the cam from slipping. Test the motor by pressing the up button. The screen should roll up and stop when the cam hits the switch.
Calibrate the bottom limit switch the same way
Most motorized screens have two limit switches: one at the top and one at the bottom. After you calibrate the top switch, you must calibrate the bottom one. Have someone press the down button to roll the screen all the way down. Stop the motor before the screen reaches the bottom, then manually rotate the motor shaft to position the bottom cam just before it touches its switch.
Loosen the bottom cam's set screw, rotate the cam to the correct position, and tighten it. Test by pressing the down button — the screen should roll down and stop at the bottom without jerking or overshooting.
If your screen has only one limit switch (some budget models do), you only need to calibrate that one.
Test the screen and close the tube
With power still off, manually roll the screen up and down by hand to make sure the cams move freely and don't bind. Then restore power and test the motor. Press the up button and watch the screen roll up. It should stop smoothly when it reaches the top. Press the down button and watch it roll down and stop at the bottom.
If the screen overshoots or stops too early, the cam is still slightly out of position. Disconnect power again, loosen the cam set screw, adjust it a small amount, and tighten it. Retest. Calibration often takes two or three tries to get exactly right.
Once the screen stops correctly at both ends, close the motor tube access panel or end cap. If you removed the screen fabric to access the tube, rewind it carefully and make sure it is centered before closing the tube. Restore full power and test one more time.
When to replace the limit switch instead of recalibrating
If the switch does not click, the lever is bent or stuck, or the contact points are burned or corroded, the switch cannot be fixed by moving the cam. The switch itself must be replaced. Replacement switches are specific to each screen model, so you will need the exact model number.
Contact the screen manufacturer's customer service with your model number and ask for the replacement switch part number and installation instructions. Some switches are soldered to the motor housing and require a soldering iron to remove and install. If you are not comfortable soldering, a technician can do it for $75 to $150 in labor.
If your screen is still under warranty, contact the manufacturer about a warranty replacement before you buy a new switch yourself.
Frequently Asked Questions
Can I calibrate the limit switch without opening the motor tube?
No. The cam and switch are inside the tube, and you cannot reach them from outside. You must open the tube to adjust the cam position. Some screens have an access panel specifically for this purpose, which is faster than removing the screen fabric.
What if the screen still won't stop after I recalibrate?
The motor may have a separate electrical problem — a relay or capacitor that is not cutting power when the switch clicks. If the switch clicks and moves but the motor keeps running, the problem is in the control circuit, not the limit switch. This requires a technician or a replacement control board.
How often do limit switches need to be recalibrated?
A properly installed limit switch should not drift out of calibration during normal use. If you find yourself recalibrating it every few months, the cam set screw may be loose or the motor shaft may be bent. Check that the set screw is tight and that the shaft spins smoothly without wobbling.
Can I use a different brand of limit switch if mine breaks?
No. Limit switches are specific to each motor model because the cam shape and switch mounting bracket are designed to work together. Using a different switch will not align properly with your cam. Always order the exact replacement part from the screen manufacturer.
Is it safe to manually roll the screen up and down while testing?
Yes, as long as power is disconnected. Manually rotating the motor shaft or rolling the screen by hand is safe and is actually the correct way to test the cams and switches during calibration. Never manually roll the screen when power is on, because the motor could suddenly start and pinch your fingers.