Recessed ceiling screens mount inside a soffit or dropped frame so the screen rolls up and disappears when not in use
A recessed projector screen hides completely in the ceiling cavity when retracted, leaving only a thin trim ring visible. The screen itself sits in a motorized housing that pulls it down when you want to watch and retracts it back up into the soffit or frame when you're done. This is different from a surface-mounted screen, which hangs visibly on the wall or ceiling even when rolled up.
The main requirement is ceiling space — you need at least 4 to 6 inches of depth above the finished ceiling to fit the motor housing and rolled screen. If your ceiling is drywall over joists, you can build a soffit (a dropped frame) to create that space. If you have a suspended ceiling with a plenum above, you can mount directly into the structural space. Either way, the screen stays hidden until you lower it.
Key Takeaways
- Recessed screens need 4 to 6 inches of ceiling depth, which you can create by building a soffit or using existing plenum space in a suspended ceiling.
- Motorized screens cost more than manual ones but roll up and down at the push of a button, making them practical for everyday use.
- You will need to run power to the motor and often run a control wire or wireless receiver, which is easier to hide during new construction than retrofit.
- Drywall, framing, and trim work around the screen opening is usually the largest part of the job, not the screen itself.
- A professional installer can may support the frame is level, the screen hangs straight, and the motor is wired correctly — mistakes here cause binding and noise.
Assess your ceiling space and structure
Before buying a screen, measure the space above your finished ceiling. If you have a standard drywall ceiling, look in the attic or crawl space directly above where you want the screen. You need at least 4 to 6 inches of clear depth between the top of the drywall and the underside of the joists or roof structure. If there are ducts, pipes, or wiring in that space, you may need to reroute them — this is a job for a contractor.
If you have a suspended (drop) ceiling with a plenum above, you have more flexibility. The space above the tiles is usually 12 to 24 inches deep, which is plenty. You can mount the screen housing directly to the structural ceiling or to the grid system, depending on the weight and your local building code.
Measure the width and height of the wall or area where you want the screen to appear. Screens come in standard sizes — 100 inches, 120 inches, 150 inches — measured diagonally. Choose a size that fits your room and viewing distance. The housing will be slightly wider and deeper than the screen itself, so account for that in your soffit or frame design.
Build or prepare a soffit to house the screen
If you have a standard drywall ceiling and not enough natural depth, you will need to build a soffit — a shallow dropped frame that creates a pocket for the screen housing. A soffit is typically 12 to 18 inches wide and runs the full width of the screen opening, plus a few inches on each side.
Frame the soffit using 2×4 or 2×6 lumber attached to the ceiling joists and the wall. The depth should be at least 6 inches to accommodate the motor housing and rolled screen. Once the frame is in place, run drywall over it and finish the edges with trim that matches your ceiling. Leave an opening in the drywall where the screen will mount — the trim ring of the screen will cover the raw edge.
If you are building a new room or doing a major renovation, plan the soffit during the framing stage. It is much easier to build the frame and run power and control wires before drywall goes up. If you are retrofitting into an existing ceiling, you will need to cut into the drywall, reroute any wiring or ducts, and patch around the new frame — this is more disruptive and usually requires a contractor.
Run power and control wiring before installation
Motorized screens need a dedicated power source, usually a standard 120-volt outlet. The outlet should be located near the screen housing, ideally inside the soffit or hidden behind trim. If the outlet is far away, you can run a power cord through the ceiling cavity, but it must be in conduit and follow local electrical code.
Most motorized screens come with a wireless remote, so you do not need a separate control wire. However, some models use a hardwired control that runs from the motor to a wall switch or control panel. If you want a wall switch, run the control wire during framing, before drywall is installed. If you are retrofitting, you can run the wire inside the soffit or hide it behind trim.
Hire a licensed electrician to run the outlet and any hardwired controls. They will may support the circuit is properly sized, the outlet is grounded, and the installation meets code. This is not a DIY task — mistakes can cause fire or shock hazard.
Choose between motorized and manual screens
A motorized screen has an electric motor that rolls the screen up and down. You control it with a remote, wall switch, or smartphone app. Motorized screens cost more — typically $800 to $3,000 depending on size and features — but they are convenient and practical for daily use. The motor is quiet (usually 30 to 40 decibels) and the screen retracts fully into the housing.
A manual screen uses a spring-loaded roller or hand crank. You pull a cord or turn a handle to lower the screen, and it retracts on its own when you release it. Manual screens cost less — $300 to $1,000 — but they are slower and require physical effort. They are better suited to occasional use or spaces where you do not want to add electrical wiring.
For a hidden ceiling installation, motorized is usually the better choice because you do not have to reach up to operate it, and the screen retracts completely and smoothly. Manual screens can stick or bind if the frame is not perfectly level, which is more likely in a soffit where alignment is critical.
Install the screen housing and frame
Once the soffit is finished and power is run, the screen housing is mounted to the structural frame inside the soffit. The housing is a metal or composite tube that holds the rolled screen and the motor. It must be level and centered in the opening, or the screen will bind or hang crooked.
The trim ring — the visible part that frames the screen opening — is attached to the housing and sits flush with the finished ceiling. The trim comes in white, black, or custom colors to match your décor. The screen itself is attached to the bottom of the housing and rolls down when you set up the motor.
This step is best left to a professional installer. They have the tools to level the housing precisely, align the screen, and test the motor under load. A screen that is even slightly out of level will bind, make noise, or wear unevenly. If you do install it yourself, use a laser level and have a helper hold the housing while you fasten it.
Finish trim and test the mechanism
Once the screen is mounted, finish any drywall seams around the soffit and paint or texture to match the ceiling. The trim ring of the screen will cover the gap between the housing and the drywall, so you do not need to tape and mud that edge — just make sure the drywall is cut cleanly.
Before you consider the job done, test the screen multiple times. Lower it fully and check that it hangs straight and does not bind at the sides. Raise it fully and listen for grinding or squeaking — these are signs of misalignment or a motor problem. If the screen is motorized, test the remote and any wall switches. If it is manual, check that the spring tension is even and the screen does not drop or stick.
If the screen binds, makes noise, or does not retract fully, stop using it and call the installer or manufacturer. Continuing to use a misaligned screen will damage the roller and the fabric.
Frequently Asked Questions
Can I install a recessed screen in a room with low ceiling clearance?
If you have less than 4 inches of space above the drywall, you cannot fit a standard motorized housing. You can use a manual screen with a thinner housing, or mount a surface screen on the wall instead. Some ultra-thin motorized screens exist but are expensive and have limited size options.
What happens if my soffit is not perfectly level?
A screen that is even slightly out of level will bind when it rolls up or down. The roller will catch on one side of the housing, causing noise and wear. Always use a laser level when building the soffit frame and mounting the housing. If your soffit is already built and the screen binds, you may need to shim the housing or rebuild the soffit.
Can I hide the power cord for a motorized screen?
Yes, run the power cord through the ceiling cavity in conduit and bring it down inside the soffit to a hidden outlet. The outlet can be mounted on the inside of the soffit frame where it is not visible. A licensed electrician should do this work to may support it meets code.
How do I clean a recessed projector screen?
Most projector screens have a vinyl or fabric surface that collects dust. Gently wipe it with a soft, dry cloth when the screen is fully extended. Do not use water, solvents, or abrasive cleaners — these can damage the material. If dust builds up inside the housing, you may need to have a professional clean it.
What is the difference between a recessed screen and a motorized wall-mounted screen?
A recessed screen hides in the ceiling and takes up no visible space when retracted. A motorized wall-mounted screen hangs on the wall and rolls up into a visible case. Recessed screens look cleaner and are better for rooms where you want the ceiling to look finished, but they cost more and require soffit construction.