A basic projector you can make from a magnifying glass and a phone
You can build a working projector for tracing using a magnifying glass, a cardboard box, and a smartphone or small light source. The magnifying glass acts as a lens to enlarge and focus an image onto a wall or paper, and the box holds everything in the right position. This method costs under $20 if you already own a phone, and it works well enough to trace outlines of photos, drawings, or printed images onto a larger surface.
The projector works because a magnifying glass bends light rays to make small objects appear larger. When you place a light source and an image at the right distance from the lens, the light passes through the image, gets magnified by the lens, and projects onto a wall. The tricky part is getting the distances right — too close and the image blurs, too far and it becomes too dim to see clearly.
Key Takeaways
- A magnifying glass with a focal length between 4 and 8 inches works best; you can find the focal length by focusing sunlight onto a piece of paper outdoors.
- The image source (phone screen or printed photo) must sit between the focal length and twice the focal length from the lens for a clear, enlarged projection.
- A dark room or covered space makes the projection much brighter and easier to see, since the image is not very bright even in ideal conditions.
- The projector inverts the image upside down, so you will need to flip your phone screen or printed image before you start tracing.
- This method works best for straightforward outlines and bold shapes; fine details and small text may be too blurry to trace accurately.
What you need to gather
Start with a magnifying glass — a 3-inch or 4-inch diameter lens works well. Avoid tiny pocket magnifiers; they do not bend light enough. You can test a magnifying glass before you buy by holding it in sunlight and moving it toward a piece of paper until the light focuses into the smallest, brightest spot. That distance is the focal length, and you want one between 4 and 8 inches.
Next, gather a cardboard box large enough to hold your light source and lens. A shoe box, small storage box, or even a paper towel tube works. You will also need your image source — either a smartphone with the image displayed on the screen, or a printed photo or drawing. A light source is essential: a smartphone flashlight, a small LED flashlight, or a desk lamp all work, though a phone's built-in flashlight is the easiest because it doubles as your image source.
You will need tape (duct tape or masking tape), a utility knife or box cutter to cut holes in the cardboard, and black construction paper or black tape to block stray light and reduce glare. A white wall, white poster board, or white sheet serves as your projection surface.
Building the box and mounting the lens
Cut a hole in one end of the cardboard box slightly smaller than the diameter of your magnifying glass. The hole should be clean and round so the lens sits flush. Tape the magnifying glass over the hole from the outside, using duct tape around the rim. Make sure the lens is find and does not wobble.
On the opposite end of the box, cut a smaller hole for your light source to shine through, or leave one end open if you are using a phone flashlight. If you are using a separate flashlight, tape it inside the box pointing toward the lens. Line the inside of the box with black construction paper or black tape to absorb stray light and prevent reflections that wash out your image.
If you are using a smartphone as both the light source and image display, you can place it inside the box with the screen facing the lens, or position it outside the box and shine its light through a hole. Experiment with placement — the phone screen should be between the focal length and twice the focal length away from the lens for a clear image.
Positioning the image and focusing
Place your image source (phone screen or printed image) inside the box between the light source and the lens. If you are using a phone, flip the image upside down on the screen first, because the projection will invert it again and show it right-side up on the wall. For a printed image, flip the paper upside down as well.
Darken the room as much as possible — close curtains, turn off overhead lights, and cover windows. Aim the lens at a white wall or white poster board about 3 to 6 feet away. Move the box closer to or farther from the wall until the image comes into focus. You may need to adjust the distance between the image source and the lens inside the box as well. This takes patience; small movements make a big difference.
If the image is too dim, move the box closer to the wall or use a brighter light source. If it is too blurry, check that the image source is at the right distance from the lens — usually between 6 and 12 inches, depending on your magnifying glass's focal length. If the image is upside down on the wall, you flipped the source image correctly; that is how this projector works.
Tracing from the projected image
Once the image is focused and bright enough to see, tape a piece of white paper or poster board to the wall where the image projects. You can now trace the outline with a pencil, pen, or marker. Work in a dark room so the projection stays visible. If you need to trace fine details, move the box closer to the wall to make the image larger, though this may make it slightly dimmer.
For best results, trace only the main outlines and bold shapes. Small text, thin lines, and fine details often blur too much to trace accurately with this method. If you are tracing a face or figure, focus on the overall proportions and major features first, then add details by hand afterward.
Troubleshooting common problems
The image is too dim to see: Move the box closer to the wall, use a brighter light source (a desk lamp works better than a phone flashlight), or darken the room further. You can also try a larger magnifying glass, which gathers more light.
The image is blurry: The image source is probably too close to or too far from the lens. Move it in small increments — even half an inch matters. Also check that the lens is clean and not smudged. If the edges are sharp but the center is blurry, the lens may be tilted; adjust the tape holding it until it is perpendicular to the box.
The image is too small: Move the box farther from the wall, or use a magnifying glass with a longer focal length (weaker magnification). You can also move the image source closer to the lens, though this reduces brightness.
Light is leaking around the lens: Seal gaps with black tape or black construction paper. Stray light washes out the image and makes it harder to see. Check all seams and edges of the box as well.
When to use a different method
A homemade projector works well for tracing straightforward shapes, outlines, and bold images. If you need to trace fine details, small text, or very precise lines, a commercial projector, a light box, or a window-tracing method may give better results. A light box (which you can also make from a picture frame and a phone flashlight) works better for detailed work because the image does not need to be magnified.
If you are tracing a large mural or wall-sized image, a commercial projector is worth renting or borrowing, since it is brighter and easier to focus. For everyday tracing tasks — enlarging a photo to paint, copying a drawing to a larger scale, or projecting a pattern onto fabric — the homemade version is fast, cheap, and effective enough.
Frequently Asked Questions
Can I use any magnifying glass?
Not all magnifying glasses work equally well. You need one with a focal length between 4 and 8 inches — too short and the image is too small, too long and it is too dim. Test the lens in sunlight first by focusing the light onto a piece of paper and measuring the distance. Avoid tiny pocket magnifiers; they do not bend light enough to create a usable projection.
Do I need a completely dark room?
The darker the room, the brighter and clearer the projection will be. You do not need total darkness, but closing curtains and turning off overhead lights makes a big difference. Even a dimly lit room works better than a bright one. If you are working during the day, cover windows with blankets or cardboard.
Why is my image upside down?
That is how magnifying lenses work — they flip the image. To get a right-side-up projection on the wall, flip your image source (phone screen or printed picture) upside down before you place it in the projector. The two flips cancel each other out.
Can I use a phone flashlight instead of a desk lamp?
Yes, a phone flashlight works, and it is convenient because the phone can also display the image. The projection will be dimmer than with a desk lamp, so you will need a darker room. For brighter results, use a separate LED flashlight or a small desk lamp as the light source.
What if the image is still too blurry after I adjust the distance?
Check that the magnifying glass is clean and not smudged. Make sure the lens is perpendicular to the box — if it is tilted, the image will blur. Also verify that your image source is flat and not curved or wrinkled. If the edges are sharp but the center is blurry, the lens may have a curved field, which is normal for cheap magnifiers; move the image source slightly closer to the lens.