Clean the exterior and rollers first, then the glass
Most scanner problems come from dust and paper debris stuck inside. Start by unplugging the scanner, then wipe the outside casing with a soft, dry cloth. Open the scanner lid or access panel — your manual will show you where — and look for visible dust or torn paper bits around the rollers and feed path.
Use a dry cotton swab or soft brush to gently remove debris from the rollers (the rubber wheels that pull paper through). Do not use water or cleaning solution on the rollers themselves; moisture can make them slip and cause paper jams. If a roller feels sticky or gummy, a swab barely dampened with distilled water can help, but let it dry completely before closing the scanner.
For the glass scanning surface, use a microfiber cloth or lens tissue slightly dampened with distilled water. Wipe in one direction, not circles. If the glass has stubborn marks, a 50/50 mix of distilled water and white vinegar works, but never spray liquid directly onto the scanner — spray it onto the cloth first, then wipe the glass.
Key Takeaways
- Always unplug the scanner before cleaning any internal parts to avoid electrical hazard and accidental operation.
- Use only dry cloths on rollers and feed paths; moisture on rubber parts causes paper jams and slipping.
- Clean the glass scanning surface with a microfiber cloth and distilled water, never tap water, which leaves mineral deposits.
- Replace the feed roller or separation pad if paper jams continue after cleaning, as these wear out over time and cannot be restored.
What not to use inside a scanner
Compressed air is tempting but risky. It can blow dust deeper into the scanner instead of out, and the pressure can damage delicate sensors or dislodge internal components. If you use it at all, use short bursts at low pressure and hold the scanner so debris falls out, not further in.
Never use paper towels, tissues, or cloth napkins on the glass or internal parts. They shed fibers that stick to sensors and rollers. Avoid alcohol, acetone, or harsh solvents — they can strip coatings from the glass or damage rubber rollers. Distilled water is safer than tap water because tap water leaves mineral streaks on the glass that affect scan quality.
Clean the feed rollers and separation pad
If your scanner has a sheet-feed tray (the kind you load paper into), the feed roller and separation pad do most of the work and collect the most dirt. The feed roller is the rubber wheel that grabs the top sheet; the separation pad is the rubber or felt strip that keeps only one sheet moving at a time.
Open the scanner and locate these parts — they are usually near the paper tray. Gently wipe the feed roller with a dry cotton swab, rotating it by hand as you go so you clean the whole surface. For the separation pad, use a swab barely dampened with distilled water. Let both dry completely before closing the scanner.
If paper still jams after cleaning, the feed roller or separation pad may be worn smooth and need replacement. Most manufacturers sell these as separate parts, and they usually cost between $15 and $40. Replacement takes five minutes and involves unclipping the old part and snapping the new one in.
Clean the glass platen and underside
The platen is the glass or plastic surface under the lid where you place a document for scanning. Dust and smudges here show up as dark spots or lines in your scans. Wipe it with a microfiber cloth and distilled water, using gentle pressure. Do not scrub or use abrasive pads.
If your scanner has a removable lid or cover, check underneath for dust buildup. Use a dry cloth or soft brush to clear it out. Some flatbed scanners have a white or gray backing behind the glass; do not clean this unless your manual says it is safe — it can be a sensor or light source.
How often to clean and when to do it
Clean your scanner every three to six months if you use it regularly, or whenever you notice scan quality dropping — dark lines, streaks, or spots that were not in the original document. If you scan a lot of old or dusty documents, clean it more often. If you scan mostly clean office paper once a week, you may only need to clean it once a year.
Clean it when ready if you notice a paper jam, because torn paper left inside will cause more jams. Also clean it right away if you spilled anything on or near it, even if nothing seems to have gotten inside — moisture can travel and cause problems later.
When to replace parts instead of cleaning
Some scanner parts wear out and cannot be cleaned back to working order. If paper keeps jamming even after you have cleaned the feed roller and separation pad, those parts are probably worn smooth and need replacement. If the glass has scratches or cracks, it needs replacement — no amount of cleaning will fix it.
If the scanner still does not scan properly after cleaning, the problem may be inside the light source or sensor, which you should not try to clean yourself. At that point, contact the manufacturer or a repair shop. Trying to clean internal optics can cause permanent damage.
Frequently Asked Questions
Can I use Windex or glass cleaner on the scanning glass?
No. Windex and similar cleaners leave streaks and residue that show up in scans. Distilled water with a microfiber cloth is safer and works just as well. If you need extra cleaning power, use a 50/50 mix of distilled water and white vinegar instead.
What if I see dust inside the scanner but cannot reach it?
Do not force anything into the scanner to reach it. Use a dry cotton swab or soft brush to gently sweep debris toward the opening where you can pull it out. If dust is truly unreachable, it is probably not affecting scan quality. If scans look dirty, the problem is usually on the glass or rollers, which you can clean.
Is it safe to clean a scanner while it is plugged in?
No. Always unplug the scanner before opening it or cleaning any internal parts. This prevents accidental operation and electrical hazard. Wait at least 30 seconds after unplugging before opening the scanner, in case there is residual power.
How do I know if the feed roller needs replacement?
If paper jams frequently, skips pages, or feeds multiple sheets at once even after cleaning, the feed roller is probably worn. You can also look at it — if it feels smooth and slippery instead of slightly grippy, it is time to replace it. Replacement rollers are inexpensive and take just a few minutes to install.
Can I use a hair dryer to dry the scanner after cleaning?
No. Heat can damage internal components and sensors. Let the scanner air-dry completely after cleaning — usually 30 minutes to an hour. Make sure all moisture is gone before plugging it back in or closing the lid.