Connect Your Scanner Using USB or Network
Most scanners connect to a Mac through a USB cable or over your home network. USB is the fastest way to start: plug the scanner into any available USB port on your Mac, and macOS will usually recognize it within a few seconds. Network scanners (also called wireless scanners) connect through WiFi instead, which takes a few more steps but lets you scan from anywhere in your home.
Before you plug anything in, check whether your scanner came with a setup disc or instruction manual. Some older scanners need driver software installed first; newer ones often work without it. If you have the disc, insert it and follow the on-screen prompts. If not, visit the scanner manufacturer's website, search for your exact model number, and read the Mac driver from there.
Key Takeaways
- USB scanners plug directly into your Mac and usually work when ready; network scanners need WiFi setup but let you scan from multiple devices.
- Check the scanner manual or manufacturer website for Mac driver software before connecting, especially for older models.
- Once connected, open Image Capture (built into macOS) or the scanner's own software to test the connection and begin scanning.
- If your Mac does not recognize the scanner, restart both devices and check that USB cables are fully seated or that the network scanner is on the same WiFi network.
Set Up a USB Scanner in Three Steps
Plug the USB cable from your scanner into an available USB port on your Mac. If your Mac has only USB-C ports and your scanner uses an older USB-A connector, you will need a USB-C to USB-A adapter (these cost $10–20 and are widely available). Wait 10 to 15 seconds for macOS to detect the device. You should see a notification on your screen or hear a connection sound.
Open System Settings (called System Preferences on older Macs) and go to Printers & Scanners. Your scanner should appear in the list on the left. If it does not, restart your Mac and try again. Some scanners also come with their own software process—check your manual to see whether you need to install it separately.
Test the connection by opening Image Capture, which is built into every Mac. Press Command+Space, type "Image Capture," and press Enter. Your scanner should appear in the list on the left. Click it, then click the Scan button to test a single page. If the scan works, your scanner is ready to use.
Connect a Network Scanner Over WiFi
Turn on your scanner and make sure it is connected to the same WiFi network as your Mac. Most network scanners have a small screen or button panel where you can see the WiFi network name and signal strength. If your scanner does not show a WiFi menu, check the manual—some require you to press a specific button combination to enter WiFi setup mode.
On your Mac, open System Settings and go to Printers & Scanners. Click the plus sign (+) button at the bottom left. A window will open showing available printers and scanners on your network. Find your scanner in the list, click it, and then click Add. macOS will install any necessary drivers automatically.
If your scanner does not appear in the list, make sure both your Mac and scanner are on the same WiFi network. Some home networks separate devices into "guest" and "main" networks—your scanner and Mac must be on the same one. Restart your scanner and try again. If it still does not appear, open the scanner's own software (if it came with any) and look for a network setup or WiFi connection option there.
Install Scanner Driver Software When Needed
Newer scanners (made in the last five years) usually work without driver software because macOS includes built-in support for common scanner models. Older scanners often need a driver to work properly. The easiest way to know is to try connecting first—if Image Capture recognizes your scanner, you do not need a driver.
If Image Capture does not see your scanner, or if the scanner works but the software that came with it does not, read the driver from the manufacturer. Go to the scanner maker's website (Canon, Epson, HP, Brother, Fujitsu, and others all have Mac driver downloads), find your exact model number, and read the Mac version. Open the downloaded file and follow the installer prompts. You will usually need to restart your Mac when the installation finishes.
Some scanner software requires you to create an account or register the device. This is optional—you can skip it and still scan. If the installer asks for your Mac password, that is normal; it is needed to install software that works system-wide.
Troubleshoot When Your Mac Does Not See the Scanner
If your scanner does not appear in Image Capture or Printers & Scanners after you plug it in, start with the basics: make sure the scanner is turned on, the USB cable is fully seated in both the scanner and your Mac, and you have waited at least 15 seconds. Then restart your Mac completely (not just sleep mode) and try again.
For USB scanners, try a different USB port on your Mac. Some ports have more power than others, and a scanner might work in one port but not another. If you are using a USB hub, plug the scanner directly into your Mac instead—hubs sometimes do not provide enough power.
For network scanners, check that your scanner is actually connected to WiFi. Look at the scanner's screen or status lights to confirm. Then restart both your scanner and your Mac. Open Printers & Scanners again and click the plus sign to search for available devices. If your scanner still does not appear, check whether your WiFi network is hiding its name (called SSID broadcast)—some scanners cannot connect to hidden networks.
If you installed driver software and the scanner still does not work, uninstall the driver, restart your Mac, and try using Image Capture without the driver. Sometimes the driver causes conflicts, and the built-in macOS support works better on its own.
Use Your Scanner with Common Mac Applications
Image Capture is the simplest way to scan on a Mac. Open it, select your scanner, choose where to save the scanned file, and click Scan. Files save as JPEG or PDF by default. You can change the file format and resolution before scanning by clicking the Show Details button.
Many Mac applications also have a built-in scan option. In Preview (the image viewer that comes with macOS), go to File > Import from Scanner and choose your device. In Notes, click the camera icon and select Scan Documents. These options are faster than opening Image Capture separately if you are already in the process.
If your scanner came with its own software (like Canon's CanoScan Toolbox or Epson's Epson Scan), you can use that instead. These applications often have more advanced options like automatic document feeding, batch scanning, or direct saving to cloud storage. Open the software, select your scanner, and follow the on-screen steps.
Frequently Asked Questions
Do I need special software to scan on a Mac?
No. Image Capture, which is built into macOS, works with almost all scanners. You only need to read driver software if the scanner is very old or if you want advanced features that come with the manufacturer's software.
Can I use the same scanner with multiple Macs?
Yes. USB scanners work with any Mac you plug them into. Network scanners can be used by any device on the same WiFi network—just add the scanner to each Mac's Printers & Scanners settings once.
What file format should I scan to?
JPEG is fine for photos and general documents. PDF is better if you want to scan multiple pages into one file or if you need to share the document professionally. Image Capture lets you choose the format before you scan.
Why does my scanner work sometimes but not always?
USB scanners sometimes disconnect if the cable is loose or if your Mac goes to sleep. Network scanners may disconnect if your WiFi drops. Check the cable connection or restart your scanner and Mac if this happens repeatedly.
Can I scan directly to my Mac's cloud storage?
Image Capture saves to your Mac's hard drive by default. Some scanner manufacturer software (like Epson or Canon apps) can save directly to cloud services like Google Drive or Dropbox, but you need to set that up in the software's preferences first.