Clean the glass and rollers first, then the interior
A scanner collects dust and paper debris inside its mechanism, which causes jams, streaks on scans, and eventually mechanical failure. The fastest way to prevent this is to clean three parts: the glass platen (the flat surface you place documents on), the feed rollers (the rubber wheels that pull paper through), and the interior dust that settles on the lens and mirrors.
Most of this cleaning takes five to ten minutes and requires only materials you already have at home. You do not need to disassemble the scanner or buy special tools. The key is doing it regularly — monthly if you scan often, or every three months if you scan occasionally.
Key Takeaways
- The glass platen and feed rollers collect the most dust and paper residue, and cleaning them monthly prevents jams and streaky scans.
- Use a soft, lint-free cloth slightly dampened with distilled water or a 50/50 mix of distilled water and isopropyl alcohol — never spray liquid directly on the scanner.
- Clean the interior lens and mirrors by opening the scanner lid and gently wiping with a dry microfiber cloth, never touching the glass with your fingers.
- Unplug the scanner before you start cleaning and let any damp parts air-dry completely before plugging it back in.
What you need to gather before you start
Collect these items before you open the scanner: a soft, lint-free cloth (microfiber works best), distilled water, isopropyl alcohol (70 percent strength is standard), and a small container to mix a cleaning solution if you choose to use one. Do not use paper towels, tissues, or cotton balls — they leave fibers behind that interfere with scanning.
If you do not have isopropyl alcohol, distilled water alone works fine for the glass and rollers. Tap water leaves mineral deposits, so avoid it. Unplug the scanner from the wall outlet before you begin, and make sure it has cooled for at least five minutes if you have been using it.
Cleaning the glass platen and document feed area
Open the scanner lid or cover to expose the glass platen — the flat glass surface where you place documents. Look for dust, paper crumbs, and any visible smudges. Dampen a corner of your cloth with distilled water or your water-alcohol mix, then wipe the glass in one direction, from the back of the scanner toward the front. Do not scrub in circles; long, straight strokes prevent streaking on your scans.
Flip the cloth to a dry section and wipe the glass again to remove any moisture. Check the document feed area (the slot where paper enters) for torn pieces of paper or dust buildup. Use a dry cloth to gently wipe out any debris you see. If paper is stuck inside, do not force it — turn the scanner on its side and let gravity help, or use a flashlight to see what you are working with before you pull.
Cleaning the feed rollers
The feed rollers are the rubber wheels inside the document feeder that grip and pull paper through the scanner. They sit at the entrance of the paper path and collect dust, paper powder, and ink residue that causes jams and misfeeds. Dampen your cloth with the same water or water-alcohol solution and wipe each roller by rotating it by hand as you clean, so you cover the entire surface.
Use gentle pressure — the rollers are rubber and can be damaged by hard scrubbing. If a roller is very dirty, you may need to wipe it two or three times, letting it dry between passes. Once the rollers look clean, use a dry cloth to remove any remaining moisture. Let them air-dry for a few minutes before you close the scanner.
Cleaning the interior lens and mirrors
Open the scanner lid fully and look inside. You will see a glass lens (usually in the center or toward the back) and possibly reflective mirrors that direct light to the sensor. These parts collect dust that degrades scan quality. Use a dry microfiber cloth only — never use liquid on the lens or mirrors, as moisture can damage the internal optics.
Gently wipe the lens and any visible mirrors with a dry cloth, using light pressure and straight strokes. Do not touch the glass with your bare fingers, as skin oils leave marks that affect scanning. If you see dust that will not come off with a dry cloth, use a cloth barely dampened with isopropyl alcohol (not water), but let it dry completely before you close the lid and plug the scanner back in.
Drying and reassembly
After you finish cleaning, leave the scanner lid open for five to ten minutes so any damp areas can air-dry completely. Check the glass platen and feed rollers one more time to make sure they are dry to the touch. If any part still feels damp, wait another few minutes.
Once everything is dry, close the lid, plug the scanner back into the wall outlet, and run a test scan on a blank page or a document you do not need. The scan should be clear with no streaks or smudges. If you see streaks, the glass or rollers may not be completely dry, or you may have left lint behind — unplug the scanner again and wipe with a fresh, dry cloth.
How often to clean and what to watch for
If you scan documents daily, clean the glass and rollers once a month. If you scan a few times a week, clean every two to three months. If you scan rarely, clean before each use. You will know it is time to clean if you notice streaks on scans, paper jams, or the scanner taking longer to process documents.
Watch for these warning signs: horizontal lines across scans (usually the glass or lens is dirty), paper not feeding smoothly (the rollers need cleaning), or the scanner making grinding sounds (debris is caught in the mechanism). If you hear grinding or the scanner will not turn on after cleaning, stop and let it sit unplugged for 30 minutes — moisture may have reached an electrical component.
Frequently Asked Questions
Can I use Windex or glass cleaner on the scanner glass?
No. Windex and similar cleaners contain ammonia and other chemicals that can damage the scanner's optical components and leave residue that interferes with scanning. Stick to distilled water or a 50/50 mix of distilled water and isopropyl alcohol.
What if paper tears inside the scanner and I cannot get it out?
Turn the scanner off and unplug it. Tilt the scanner on its side so gravity helps the paper fall out, or use a flashlight to see inside and gently guide the paper out with a plastic ruler or old credit card — never use metal objects. If the paper is wrapped around a roller, you may need to contact the manufacturer for disassembly instructions.
How long should I wait after cleaning before I use the scanner again?
Wait at least five to ten minutes for damp areas to air-dry, or longer if you used liquid on the interior. If you used isopropyl alcohol, it dries faster than water. Always make sure the glass platen and rollers feel completely dry to the touch before you plug the scanner back in and scan.
Will cleaning the scanner void the warranty?
Cleaning the exterior and accessible interior parts (glass, rollers, and the area you can see with the lid open) is normal maintenance and will not void the warranty. Do not disassemble the scanner or open sealed compartments, as that may affect coverage.
What is the difference between isopropyl alcohol and rubbing alcohol?
Rubbing alcohol is usually 70 percent isopropyl alcohol mixed with water, while pure isopropyl alcohol is 90 percent or higher. For scanner cleaning, 70 percent rubbing alcohol works fine and is easier to find. Both evaporate quickly and leave no residue, making them safe for electronics.