Clearing codes with an OBD2 scanner takes three steps: connect the scanner to your vehicle's diagnostic port, navigate to the clear or erase function, and confirm the action

Most OBD2 scanners have a dedicated button or menu option labeled "Clear Codes," "Erase Codes," or "Delete Codes." The exact wording and location depend on your scanner model, but the process is the same across nearly all devices. After you clear the codes, the check engine light turns off when ready, though the light will return if the underlying problem still exists.

Before you clear codes, write down what they say. A code like P0300 (random misfire) tells you what to fix. Once cleared, that information is gone until the problem happens again and the vehicle logs it a second time. If you clear codes without addressing the root cause, you are just hiding the warning light, not fixing the vehicle.

Key Takeaways

  • Connect your OBD2 scanner to the diagnostic port under the steering column or dashboard, usually on the driver's side, before powering it on.
  • Write down all fault codes and their descriptions before clearing, because you lose that record once the codes are erased.
  • Navigate to the clear, erase, or delete function in your scanner's menu — the exact path varies by brand and model.
  • The check engine light turns off when ready after clearing, but returns if the problem that caused the code still exists.
  • Some vehicles require the engine to run through a full drive cycle before the light stays off permanently, even after clearing codes.

Locating the diagnostic port on your vehicle

The OBD2 port is a 16-pin connector, usually rectangular and about the size of a deck of cards. On most vehicles built after 1996, it sits under the steering column on the driver's side, either mounted to the underside of the dashboard or recessed into a panel. You may need to crouch down and look up to find it, or remove a plastic cover if one is present.

Some vehicles hide the port behind a removable trim panel or inside the center console. Check your owner's manual if you cannot locate it within a minute of looking. The manual lists the exact location for your year, make, and model. Once you find it, make sure the connector is clean and free of dust before plugging in your scanner.

Powering on the scanner and connecting to your vehicle

Plug the OBD2 cable into the diagnostic port firmly until you hear or feel a click. Power on the scanner — most models turn on automatically when you insert the connector, while others have a dedicated power button. The scanner will communicate with your vehicle's computer and display a menu within a few seconds.

If the scanner does not communicate, check that the connector is fully seated in the port. A loose connection is the most common reason for "no communication" errors. If it is fully inserted and still does not work, try turning the vehicle's ignition to the "On" position without starting the engine — some vehicles require this before the diagnostic port becomes active.

Reading and recording the fault codes

Navigate to "Read Codes," "Scan," or "Diagnostics" in your scanner's main menu. The scanner displays all stored codes and pending codes. Pending codes are faults the vehicle detected but has not yet flagged with a check engine light. Write down the code number (like P0420) and the description (like "Catalyst System Efficiency Below Threshold") for each one.

The code number tells a technician or repair manual exactly what system failed. The description gives you context. A P0300 code means the engine misfired, but it does not tell you whether a spark plug is bad, the fuel injector is clogged, or the ignition coil is failing. Keeping this record helps you understand what to repair before you clear the codes and lose the information.

Finding and using the clear codes function

Return to the main menu and look for an option labeled "Clear Codes," "Erase Codes," "Delete Codes," or "Clear DTC" (Diagnostic Trouble Code). On some scanners, this option appears in a submenu under "Diagnostics" or "Service." On others, it is a dedicated button on the device itself. Check your scanner's manual if you cannot find it in the menu.

Select the clear function and confirm the action when prompted. Most scanners ask "Are you sure?" to prevent accidental clearing. Answer yes, and the scanner sends a command to your vehicle's computer to erase all stored codes. This takes a few seconds. Once complete, the scanner displays a confirmation message, and the check engine light turns off.

What happens after you clear the codes

The check engine light goes out when ready after clearing. However, if the problem that caused the code still exists, the vehicle will detect it again during normal driving and log the same code a second time. This usually takes anywhere from a few minutes to several days, depending on how often the fault occurs.

Some vehicles require a full drive cycle — a combination of city and highway driving under various engine loads and temperatures — before the system confirms the problem is fixed. If you clear codes and the light stays off after a week of normal driving, the issue was likely temporary or has been resolved. If the light returns within hours or days, the underlying problem remains.

Common reasons codes return after clearing

Codes return most often because the fault still exists. A loose gas cap, a failing oxygen sensor, or a vacuum leak will log the same code repeatedly until you fix the actual problem. Clearing codes without addressing the cause is temporary — the light will come back.

Some codes are harder to clear than others. A pending code (one the vehicle detected but has not fully confirmed) may clear and stay cleared after one drive cycle. A confirmed code (one the vehicle has logged multiple times) may require several drive cycles before the system considers it resolved. Patience and actual repair are the only reliable solutions.

Frequently Asked Questions

Will clearing codes damage my vehicle?

No. Clearing codes only erases the record of the fault from the computer's memory. It does not affect how the engine runs or any mechanical systems. The underlying problem, if it exists, remains unchanged.

Can I clear codes without a scanner?

Yes, but it is slower. Disconnecting the negative battery terminal for 10 to 15 minutes drains the vehicle's computer memory and clears codes. However, this also resets other settings like radio presets and clock time, and it does not work on all vehicles. An OBD2 scanner is faster and cleaner.

What if the same code comes back when ready after clearing?

The problem still exists and needs repair. Clearing codes again will not fix it. Use your scanner to read the code a second time and confirm it is the same one. Then research that specific code and the symptoms your vehicle is showing to identify what needs repair.

Do I need to clear codes before selling my vehicle?

Not legally, but many sellers do to make the vehicle appear healthier. A buyer with an OBD2 scanner can read the codes again if the problem persists. If you clear codes without fixing the underlying issue, you are hiding a known problem, which may create liability depending on your state's disclosure laws.

How often can I clear codes safely?

There is no limit to how many times you can clear codes. However, repeatedly clearing the same code without fixing the problem wastes time and masks a real issue. Clear codes once, drive the vehicle normally, and if the code returns, focus on repair rather than clearing again.