Programming a Uniden Bearcat Scanner: The Basic Steps
A Uniden Bearcat scanner stores radio frequencies in channels so you can listen to police, fire, and emergency services in your area. Programming means entering those frequencies into the scanner's memory, assigning them to channels, and organizing them into groups. Most Bearcat models let you program directly on the device using the keypad, though newer models also support computer software.
The exact steps depend on your Bearcat model — a BC125AT works differently from a BC895XLT — but the core process is the same: turn on the scanner, enter programming mode, select a channel, type in a frequency, name it if your model allows, and save it. This guide covers the manual keypad method, which works on nearly all Bearcat scanners.
Key Takeaways
- You need the correct frequencies for your area before you start; local police and fire departments publish these online or you can find them through RadioReference.com.
- Most Bearcat scanners enter programming mode by holding down a button (often labeled PRG or PROG) for two to three seconds until a light or tone signals you are in edit mode.
- Each frequency must be entered with the correct modulation type — FM for most police and fire, AM for some emergency services — or the scanner will not receive clearly.
- After programming, test each channel by tuning to it and listening for activity to confirm the frequency is correct and the scanner is receiving.
- Bearcat scanners sold in the United States come with blocks that prevent receiving certain frequencies; do not attempt to remove or bypass these blocks.
Finding the Right Frequencies for Your Area
Before you program anything, you need to know which frequencies your local police, fire, and emergency services use. The fastest source is RadioReference.com, a database maintained by scanner enthusiasts that lists frequencies by state, county, and city. Search for your county or city name, and you will see a list of agencies and their frequencies, usually organized by type (police dispatch, fire dispatch, emergency medical services).
You can also contact your local police or fire department directly and ask for their dispatch frequency — many departments post this information on their websites or will tell you over the phone. Write down the frequency number (usually between 150 and 500 MHz for local services) and note whether it is FM or AM. Most police and fire use FM; some emergency medical services use AM.
If you live near a state border or a large city, you may want to program frequencies from neighboring areas as well. Start with your when ready county, then expand once you understand how the scanner works.
Entering Programming Mode on Your Bearcat
The method to enter programming mode varies by model, so check your scanner's manual first — you can usually find it as a PDF on the Uniden website by searching for your model number. On most handheld Bearcat models (like the BC125AT or BC346XT), you hold down the button labeled PRG or PROG for two to three seconds. On desktop models (like the BC895XLT), you may press a menu button or use a combination of keys.
When you are in programming mode, the scanner will show a light, beep, or display a message on the screen. On models with a display, you will usually see a channel number and a prompt asking you to enter a frequency. On older models without a display, you will hear a series of beeps confirming each key press.
If you are unsure whether you are in programming mode, press a number key — the scanner should respond by beeping or showing the number on the display. If nothing happens, try holding the button longer or check your manual for the correct sequence for your specific model.
Entering Frequencies and Setting Modulation
Once you are in programming mode, the scanner will prompt you to select a channel. Channels are straightforward numbered slots in the scanner's memory — channel 1, channel 2, and so on. You can program them in any order, so start with channel 1 and work your way up. Use the number pad to enter the channel number, then press the button to confirm (usually labeled ENT or ENTER).
Next, enter the frequency. If your local police dispatch uses 460.1250 MHz, type 460.1250 using the number pad. The scanner will display or confirm the frequency. After you enter the frequency, you will be asked to set the modulation — this is the signal type the frequency uses. Press the button for FM (most common for police and fire) or AM (less common, used by some emergency services). If you choose the wrong modulation, you will hear static or nothing at all when you try to listen.
Some Bearcat models allow you to name each channel — for example, typing "POLICE" or "FIRE" — so you can identify it on the display. If your model has this feature, enter a short name (usually up to 8 characters) after setting the modulation. Then press ENT or ENTER to save the channel and move to the next one.
Programming Multiple Channels and Organizing Groups
Repeat the process for each frequency you want to program. If you have ten frequencies to enter, you will go through the channel selection, frequency entry, modulation, and name steps ten times. This takes time, but it is straightforward — each channel follows the same pattern.
Many Bearcat scanners let you organize channels into groups or banks so you can scan only police frequencies one moment and fire frequencies the next. On models with this feature, you assign each channel to a group during programming or after. Check your manual for the exact steps, as this varies widely by model. Some scanners use a menu system; others use dedicated buttons.
After you program all your channels, exit programming mode by pressing the button you used to enter it (usually PRG or PROG) or by pressing a menu button to return to normal scanning mode. The scanner should now display your channels and be ready to scan.
Testing Your Programmed Channels
Before you assume your programming is complete, test each channel to confirm it is receiving correctly. Turn on the scanner and select channel 1 (or use the scan button to cycle through all channels). Listen for activity — you should hear dispatch traffic, background noise, or at least static. If you hear nothing or only heavy static, the frequency may be wrong, the modulation may be incorrect, or the scanner may not be receiving in your area.
If a channel is not working, go back into programming mode, select that channel, and double-check the frequency and modulation against your source (RadioReference.com or your local department). A single digit wrong — 460.1250 instead of 460.1200 — will prevent the scanner from receiving. Correct the frequency, save it, and test again.
Once you have confirmed that several channels are receiving, you can be confident your programming method is correct. If you programmed twenty channels and the first five work, the rest almost certainly will too.
Common Programming Mistakes to Avoid
The most common error is entering the frequency with the wrong number of decimal places. Police frequencies in the United States use four decimal places (460.1250), not two (460.12). If you enter only two decimals, the scanner will not receive the correct frequency. Always check your source and count the decimal places before you enter.
The second most common mistake is setting the wrong modulation. If you program a frequency as AM when it should be FM, you will hear only static or nothing. Most police and fire frequencies are FM, but some emergency medical services use AM. When in doubt, try FM first — if you hear nothing, go back and change it to AM.
A third mistake is programming a frequency that does not exist in your area. RadioReference.com is usually accurate, but if you program a frequency and never hear any activity after several hours of listening, it may be inactive, out of service, or used only during emergencies. This is not a programming error — it is straightforward a frequency that is not active in your area at that moment.
Finally, do not attempt to program frequencies outside the legal range for your scanner or to remove the blocks that prevent receiving certain frequencies. Uniden Bearcat scanners sold in the United States have built-in restrictions that prevent receiving cellular, cordless phone, and other protected frequencies. These restrictions are legal requirements, and attempting to bypass them is illegal.
Using Computer Software to Program Your Scanner
If your Bearcat model supports it, you can program frequencies using a computer instead of the keypad. Uniden offers free software for many models — search "Uniden [your model number] software" on the Uniden website to see if yours is supported. You will need a USB cable to connect the scanner to your computer.
Computer programming is faster if you have many frequencies to enter, because you can paste a list of frequencies from RadioReference.com or another source instead of typing each one. However, the process is the same: you still need the correct frequencies, you still need to set the modulation for each one, and you still need to test each channel after programming.
If you use software, follow the instructions that come with it. Most software guides you through the same steps as manual programming, just with a graphical interface instead of buttons and a display.
Frequently Asked Questions
What if my Bearcat scanner will not enter programming mode?
Check your manual for the exact button combination for your model — different Bearcat models use different methods. Make sure you are holding the button long enough (usually two to three seconds). If the scanner still will not enter programming mode, the battery may be low, or the scanner may need to be reset. Try charging the battery fully, then try again.
Can I program frequencies from other states or countries?
Yes, you can program any frequency into your scanner, but your scanner will only receive frequencies that are actually broadcasting in your area. If you program a police frequency from another state, you will hear nothing because that frequency is not active where you are. Programming frequencies from outside the United States may be illegal depending on your country's regulations — check your local laws before programming international frequencies.
Why do I hear static on some channels even though I programmed them correctly?
Static usually means the frequency is correct but there is no active transmission at that moment. Police and fire frequencies are not always in use — you may hear nothing for hours, then suddenly hear dispatch traffic. If you hear only static and never any clear speech, the frequency may be inactive in your area, or you may be out of range of the transmitter. Try moving to a higher location or near a window to improve reception.
Do I need to reprogram my scanner if I move to a different city?
You can keep your old frequencies programmed if you want, but you will need to add new frequencies for your new location. Look up the police and fire frequencies for your new city on RadioReference.com and program them into empty channels. You can keep the old channels if you want to listen to your previous area, or you can delete them to make room for new ones.
What is the difference between FM and AM, and how do I know which one to use?
FM and AM are two ways radio signals are transmitted. FM is used by most police, fire, and emergency services in the United States. AM is used by some emergency medical services and older systems. Your source (RadioReference.com or your local department) will tell you which modulation to use. If you are unsure, try FM first — if you hear only static, go back and change it to AM.