Programming a Radio Shack scanner means entering the frequencies you want to monitor into the device's memory

Radio Shack sold several scanner models over the years, and the exact steps depend on which one you own. The most common models—the PRO-95, PRO-96, and BC125AT—all use a similar process: you access the programming menu, enter a frequency number, assign it to a channel, and save it. The scanner then stores that frequency and monitors it when you turn the device on.

Before you start, you need to know which frequencies to enter. Police, fire, and emergency services broadcast on specific frequencies assigned by the FCC. You can find your local frequencies through online databases like RadioReference.com or by contacting your local police department's non-emergency line and asking which frequency they use for dispatch.

Key Takeaways

  • Most Radio Shack scanners require you to enter frequencies manually through a menu system accessed by pressing the Menu or Prog button.
  • You will need the exact frequency number for the service you want to monitor, which you can find on RadioReference.com or by calling your local police department.
  • Each frequency is stored in a numbered channel slot, and you can organize channels into groups called banks so you monitor only certain services at a time.
  • Once programmed, the scanner will cycle through your active channels and alert you when it detects a transmission on any of them.

Finding the frequencies you want to monitor

The FCC assigns specific frequencies to police departments, fire services, emergency medical dispatch, and other public safety agencies. These frequencies are public information, but they vary by location. A frequency that works for police in one county will not work in another.

RadioReference.com is the most complete source. Search for your state and county, and the site lists all active frequencies for that area, organized by service type. You will see frequencies listed in MHz (megahertz)—for example, 460.125 or 155.475. Write down the exact number, including the decimal places.

If you prefer to call, your local police department's non-emergency dispatch line can tell you the main frequency they use for patrol radio traffic. They may not give you every frequency, but they will give you the primary one.

Accessing the programming menu on your scanner

The method depends on your specific Radio Shack model. On the PRO-95 and PRO-96, press the Menu button on the front panel. On the BC125AT, press the Prog button. The scanner's display will show a menu with options like "Frequency," "Channel," or "Bank."

Consult your scanner's manual to confirm the exact button sequence for your model—the manual is often available as a PDF on the manufacturer's website if you no longer have the printed version. RadioShack.com and the manufacturer's support page (usually under Uniden, Whistler, or Bearcat, depending on the model) both host manuals for older scanners.

If you cannot find the manual, search "[Your Scanner Model] programming manual" on Google. Many scanner enthusiast forums have uploaded copies or step-by-step guides specific to each model.

Entering a frequency and assigning it to a channel

Once you are in the menu, select "Frequency" or "New Channel." The scanner will prompt you to enter a number. Use the keypad to type the frequency exactly as you found it—for example, 460.125. Do not add spaces or extra characters.

After you enter the frequency, the scanner will ask you to assign it to a channel number. Channel 1, Channel 2, and so on are just storage slots. You can assign any frequency to any channel; the order does not matter. If you are organizing by service type, you might put all police frequencies in channels 1–10, fire in channels 11–20, and so on.

Some scanners also let you name each channel. If your model supports this, enter a short label like "Police Dispatch" or "Fire Main" so you can identify the frequency when it is transmitting. Press Enter or Save to store the frequency.

Organizing frequencies into banks

A bank is a group of channels that the scanner monitors together. Most Radio Shack scanners come with 10 or more banks, each holding multiple channels. Banks let you monitor only certain services without cycling through every frequency you have programmed.

For example, you might put all police frequencies in Bank 1, all fire frequencies in Bank 2, and all emergency medical frequencies in Bank 3. When you turn on the scanner, you select which bank to monitor, and the scanner cycles only through those channels.

To assign a channel to a bank, go back to the channel you just created and look for a "Bank" option in the menu. Select the bank number you want, then save. Repeat this for every frequency you add. Your manual will show the exact menu path for your model.

Testing your programmed frequencies

Once you have entered at least one frequency, turn on the scanner and select the bank or channel you programmed. Set the scanner to Scan mode (not Hold mode). The display should show the channel number and frequency. If the frequency is active, you will hear transmissions. If it is silent, the frequency may not have traffic at that moment, or you may have entered the number incorrectly.

Double-check the frequency against your source. A single digit wrong will cause the scanner to monitor the wrong frequency entirely. If you are still not hearing anything after 10 or 15 minutes, try a different frequency to confirm the scanner is working.

Some frequencies are encrypted or use digital modes that older Radio Shack scanners cannot decode. If you know a frequency is active but your scanner is silent, the service may be using encryption. Your scanner's manual will tell you whether it supports digital modes like P25 or DMR.

Saving your programming and backing it up

Radio Shack scanners store your programmed frequencies in memory even when powered off. However, if the battery dies completely or the scanner is reset, you will lose all your channels. Some newer models allow you to back up your programming to a computer using a USB cable and software.

Check your scanner's manual or the manufacturer's website to see if your model supports computer backup. If it does, read the programming software and connect your scanner to a computer. The software will let you save your channels to a file, which you can restore later if needed.

If your scanner does not support computer backup, write down all your frequencies and channel assignments in a notebook or spreadsheet. If you ever need to reprogram, you will have the information ready.

Frequently Asked Questions

What is the difference between Scan and Hold mode?

Scan mode makes the scanner cycle through all active channels in your selected bank, stopping briefly on each one to listen for transmissions. Hold mode locks the scanner on a single channel. Use Scan to monitor multiple frequencies; use Hold to listen to one specific service.

Can I program a Radio Shack scanner from my computer?

Some newer models like the BC125AT support computer programming via USB cable and software. Older models like the PRO-95 and PRO-96 require manual entry through the keypad. Check your manual or the manufacturer's website to see if your model has computer software available.

Why am I not hearing anything on a frequency I programmed?

The frequency may be correct but inactive at that moment, or you may have entered a digit wrong. Double-check the number against your source. If the frequency is correct and you still hear nothing after 15 minutes, the service may be using encryption or digital modes your scanner cannot decode.

Can I program frequencies from other states or counties?

Yes, you can enter any frequency into your scanner. However, you will only hear transmissions from that frequency if you are within range of the transmitter. Most police and fire frequencies have a range of 10 to 30 miles depending on terrain and antenna height.

What happens if I enter a frequency incorrectly?

The scanner will monitor the wrong frequency and you will not hear the service you intended. Edit the channel by going back into the menu, selecting the channel number, and re-entering the correct frequency. Save the change and test again.