Taking a Temperature with an Exergen Temporal Scanner

An Exergen temporal scanner reads body temperature by measuring infrared heat from the temporal artery, a blood vessel that runs across your forehead just under the skin. You hold the scanner about half an inch away from the center of the forehead and press the button once—it takes the reading in one to two seconds. The temperature appears on the small screen when ready, and the device beeps to signal it is done.

The scanner works without touching the skin, which makes it faster and more hygienic than other thermometers. It is also less disruptive than oral or ear thermometers, so it works well for infants, young children, and people who are sleeping or uncomfortable with other methods.

Key Takeaways

  • Position the scanner half an inch from the center of the forehead, directly above the eyebrows, and press the button once to read the temperature in one to two seconds.
  • Wipe the scanner lens with a clean, dry cloth before each use to remove dust or moisture that can block the infrared sensor.
  • Wait at least 15 minutes after the person has been in direct sunlight, worn a hat, or sweated heavily, because heat on the forehead can raise the reading by one degree or more.
  • If the reading seems wrong, take a second reading on the other side of the forehead or wait a few minutes and try again, because movement or skin moisture can cause false high readings.

Preparing the Scanner and the Person

Before you take a temperature, clean the lens on the front of the scanner with a soft, dry cloth. Dust, sweat, or dried skin oils block the infrared sensor and cause inaccurate readings. If the lens is wet, dry it completely—moisture interferes with the infrared signal just as much as dirt does.

Ask the person whose temperature you are taking to sit still for a moment. If they have been in direct sunlight, wearing a hat, or exercising, wait 15 minutes before scanning. Heat trapped on the forehead from any of these sources can add one degree or more to the reading. The same applies if they have been sweating—let the forehead dry first.

If the person is wearing a hat or headband, remove it and wait a minute or two for the forehead to cool. If they have been lying on their side, make sure you scan the side of the forehead that was not pressed against the pillow.

Positioning the Scanner Correctly

Hold the scanner so the lens points straight at the center of the forehead, directly above the eyebrows and between the eyebrows. The distance should be about half an inch—roughly the width of your pinky finger. If you hold it too far away, the reading will be too low. If you press it against the skin, you may get an inaccurate reading because you are blocking the infrared signal.

Keep the scanner still while you press the button. Do not move it side to side or up and down during the scan. Movement can interrupt the infrared reading and cause the device to show an error or a false temperature.

If you are scanning a sleeping child or infant, approach slowly and gently so you do not startle them awake. Position the scanner, press the button, and step back when ready. The entire process takes only a second or two.

Reading the Display and Understanding Results

When you press the button, the scanner sends a beam of infrared light to the forehead and measures how much heat bounces back. The temperature appears on the screen in the units your scanner is set to—Fahrenheit or Celsius. Most Exergen models beep once when the reading is complete and the number stops changing on the screen.

A normal temperature for most people is between 97°F and 99°F (36.1°C to 37.2°C) when measured on the temporal artery. Temporal readings run slightly lower than oral readings, so a temporal reading of 99°F is roughly equal to an oral reading of 100°F. If you are unsure whether a reading is normal for the person you are measuring, compare it to their baseline temperature when they are healthy.

If the scanner shows "Lo" or "Hi" on the screen, or if the number seems wrong, the lens may be dirty, the distance may be incorrect, or the person may have just come in from heat or cold. Clean the lens, wait a moment, and try again on the other side of the forehead.

Troubleshooting Common Problems

If the scanner shows a temperature that seems too high, check whether the person has been sweating, in the sun, or wearing a hat. Even if they say they have not, forehead heat can linger for 15 minutes or longer. Take a second reading after waiting a few minutes, or scan the other side of the forehead. If both readings are the same and higher than expected, the high temperature is likely real.

If the scanner shows a temperature that seems too low, the lens may be dirty or you may be holding it too far away. Clean the lens with a dry cloth and try again, keeping the scanner about half an inch from the skin. If the low reading happens only on one side of the forehead, try the other side—one side may be cooler due to air conditioning, a fan, or recent contact with a cold object.

If the scanner does not beep or the screen stays blank, the batteries may be dead. Replace them with fresh alkaline batteries of the correct size—check the manual or the battery compartment to see what type your model uses. If the screen still does not light up after new batteries, the scanner may need service.

Caring for Your Scanner Between Uses

Store the scanner in a clean, dry place at room temperature. Do not leave it in direct sunlight, in a hot car, or in a damp bathroom, because heat and moisture can damage the infrared sensor. Keep the lens cap on when you are not using it to protect the lens from dust.

Check the lens before each use and wipe it with a clean, dry cloth if you see any dust, fingerprints, or dried residue. Do not use water, alcohol, or cleaning solutions on the lens—these can damage the coating that allows the infrared sensor to work. If the lens is scratched or cloudy, the scanner may not read accurately and may need to be replaced.

Replace the batteries when the scanner stops beeping or the screen becomes dim. Most Exergen models use two or four AA or AAA batteries depending on the model. Check your manual for the correct battery type and how to open the battery compartment safely.

When to Use a Temporal Scanner and When to Choose Another Method

A temporal scanner is the fastest and least invasive option for most situations—taking a temperature at a glance without waking a sleeping child or asking someone to hold a thermometer in their mouth. It works well for infants, young children, people with sensory sensitivities, and anyone in a hurry.

An oral thermometer may be more accurate for adults who can hold it still under the tongue for the full time required. An ear thermometer works quickly but can be less accurate if earwax blocks the sensor or if you do not insert it correctly. A rectal thermometer is the most accurate for infants under three months old, though it is more invasive and takes longer.

If you are comparing temperatures across different methods or over time, use the same method each time. A temporal reading of 99°F is not directly comparable to an oral reading of 99°F because the two methods measure slightly different temperatures. Stick with one method so you can track whether the temperature is rising, falling, or staying the same.

Frequently Asked Questions

Can I use a temporal scanner on a baby?

Yes, temporal scanners work well on infants and babies because they do not require the baby to cooperate or stay still for long. The reading takes one to two seconds, so you can scan a sleeping infant without waking them. For newborns under three months old, a rectal thermometer is still considered more accurate, but a temporal scanner is a good option if you need a quick reading and the baby is older than three months.

Why does my scanner give different readings each time?

The most common cause is a dirty lens or incorrect positioning. Clean the lens with a dry cloth before each use and hold the scanner exactly half an inch from the center of the forehead. If the person has been sweating, in the sun, or wearing a hat, wait 15 minutes before scanning. If readings are still different, try scanning the other side of the forehead—one side may be cooler due to air flow or recent contact with something cold.

Is a temporal reading the same as an oral reading?

No. A temporal reading runs about one degree lower than an oral reading on the same person. So a temporal reading of 99°F is roughly equal to an oral reading of 100°F. If you are tracking someone's temperature over time, use the same method each time so the readings are comparable.

What should I do if the scanner shows an error code?

An error code usually means the lens is dirty, the batteries are low, or you are holding the scanner too far from the forehead. Clean the lens with a dry cloth, replace the batteries if they are old, and try again with the scanner held about half an inch away. If the error persists, the scanner may need service or replacement.

Can I use a temporal scanner through a forehead patch or sticker?

No. Anything covering the forehead—a patch, sticker, bandage, or even heavy makeup—blocks the infrared signal and causes an inaccurate reading. Make sure the forehead is clean and uncovered before you scan.