Connect the scanner to your car's OBD2 port and turn on the ignition

The OBD2 port is a standardized diagnostic connector found on nearly every car made after 1996. On most vehicles, it sits under the steering wheel on the driver's side, sometimes hidden behind a panel you can pop off by hand. Locate it, then plug the Ancel scanner's cable directly into the port — it only fits one way.

Turn your car's ignition to the "On" position without starting the engine. The scanner will power up automatically once it detects the connection. You should see the Ancel logo or a welcome screen appear on the device's display within a few seconds. If nothing happens, check that the cable is fully seated in the port.

Do not start the engine yet. The scanner communicates with your car's computer while the ignition is on, and starting the engine can interrupt the connection or cause the scanner to reset.

Key Takeaways

  • The OBD2 port is under your steering wheel on the driver's side, and the scanner cable plugs in with the ignition on but the engine off.
  • Most Ancel models display trouble codes as four-character alphanumeric codes (like P0300) that point to a specific system or sensor problem.
  • You can clear codes after you have noted them, but clearing without fixing the underlying problem means the code will return when the condition happens again.
  • The scanner stores live data from your engine sensors, which helps a mechanic understand what was happening when a fault occurred.

Navigate the main menu to find the "Read Codes" option

Once the scanner is connected and powered, use the arrow buttons on the device to scroll through the menu. Most Ancel models show options like "Read Codes," "Clear Codes," "Live Data," and "Vehicle Information" on the home screen. Press the button marked "OK" or "Enter" to select "Read Codes."

The scanner will communicate with your car's computer for a few seconds. You may see a loading bar or a message saying "Communicating" — this is normal. Once the scan is complete, the display will show any trouble codes that are stored in your vehicle's system.

Understand what the trouble codes mean

Trouble codes are four-character combinations that start with a letter followed by four numbers, like P0300 or C0045. The first letter tells you which system the code relates to: P codes are powertrain (engine, transmission, emissions), C codes are chassis (brakes, suspension), B codes are body (windows, seats, lights), and U codes are network or communication faults.

The Ancel scanner displays a brief description of each code on its screen. For example, P0300 means "Random/Multiple Cylinder Misfire Detected." This tells you the general problem area, but not always the root cause — a misfire can be caused by a bad spark plug, a fuel injector, a coil pack, or low fuel pressure. Write down the exact code and description so you can research it further or show it to a mechanic.

If multiple codes appear, note all of them. Sometimes one problem triggers several codes, and sometimes you have multiple separate issues. A mechanic can use the full list to narrow down the actual cause.

Check live data to see real-time sensor readings

After reading the codes, return to the main menu and select "Live Data" or "Data Stream." This shows you real-time readings from your engine sensors while the ignition is on. You will see values like engine RPM, coolant temperature, fuel pressure, oxygen sensor voltage, and throttle position.

Live data is most useful when you are working with a mechanic or trying to understand what your engine was doing when a fault occurred. For example, if you have a code for low fuel pressure, you can watch the fuel pressure reading in live data to see if it drops below the normal range. Normal values vary by vehicle, so compare what you see to the specifications in your car's service manual.

You do not need to understand every value in live data to use the scanner. The main purpose is to give a mechanic a snapshot of what the engine was doing when the problem happened.

Clear codes only after you have noted them and addressed the problem

Once you have written down all the trouble codes and their descriptions, you can clear them from the scanner's menu. Return to the main screen, select "Clear Codes," and confirm when the scanner asks if you are sure. The codes will be erased from your car's computer.

Clearing codes does not fix the underlying problem — it only removes the record. If the fault still exists, the code will return within a few days or a few hundred miles of driving, depending on how often the condition occurs. Clear codes only after you have repaired the issue or confirmed with a mechanic that the code was a false alarm.

Some codes are harder to clear than others. If a code reappears when ready after clearing, the problem is still active and needs attention before you drive the car.

Disconnect the scanner and review what you found

Once you are done reading codes and live data, turn off the ignition and unplug the scanner from the OBD2 port. The scanner will power down automatically. Keep your notes of the trouble codes in a safe place — you will need them if you take the car to a mechanic or if the same code appears again later.

If you found codes, your next step is usually to research what they mean or take the car to a mechanic. Many repair shops will read your codes for free, but having the codes already written down saves time and money. If you cleared the codes, monitor your car over the next week or two to see if the check engine light comes back on, which would tell you the problem was not actually fixed.

Frequently Asked Questions

What if the scanner says "Unable to Connect"?

First, turn off the ignition, unplug the scanner, and check that the OBD2 port is not blocked by debris or a panel. Plug the scanner back in firmly and turn the ignition on again. If the error persists, your car may have a dead battery or a blown fuse in the OBD2 circuit — check your car's fuse box or have a mechanic test the port with a multimeter.

Can I use the Ancel scanner on any car?

The Ancel works on most cars made after 1996 that have an OBD2 port. Some older vehicles, some European imports, and some specialty vehicles may not be fully compatible. Check the Ancel model number against the manufacturer's compatibility list before you buy, or ask the seller if you are unsure.

Do I need to start the engine to read codes?

No. You can read stored codes with the ignition on and the engine off. However, some scanners can read "pending" codes only while the engine is running. If you want to check live data or see what the engine is doing right now, you will need to start the engine and keep it running while the scanner is connected.

What does it mean if the check engine light comes back after I cleared the codes?

It means the problem that caused the code is still happening. The code was not a one-time glitch — it is a recurring fault. Do not clear the codes again without fixing the underlying issue. Take the car to a mechanic or research the code more deeply to understand what needs to be repaired.

Can the scanner damage my car?

No. The OBD2 scanner only reads data from your car's computer; it does not send commands that change engine settings or fuel injection. Plugging it in and reading codes is completely safe. Clearing codes is also safe — it only erases the record, not the car's programming.