What the Opex Falcon Scanner Does and How to Start

The Opex Falcon is a high-speed document scanner designed to process large batches of paper quickly and convert them to digital images. It feeds sheets automatically, scans both sides at once, and sorts or stacks the originals as they exit. If you are working with stacks of invoices, contracts, medical records, or any mixed batch of pages, the Falcon handles the feeding and imaging without you touching each sheet individually.

Before you load paper, you need to power on the machine, check that the hopper (the input tray) is empty and clean, and make sure the output trays are positioned correctly. The Falcon has a control panel on the front with a touchscreen display that shows job settings, page counts, and error messages. Most of your setup happens through this screen or through the software on the computer connected to the scanner.

The software that runs the Falcon is usually Opex ImageWare or a similar capture process installed on a workstation. This software lets you set scanning parameters—resolution, color mode, whether to scan one or both sides—before you start a batch. Once you configure the job, you load paper and press Start on the scanner itself.

Key Takeaways

  • Load paper into the hopper with the first page face-down and the top edge toward the scanner's feed rollers, and the Falcon will pull sheets one at a time and scan both sides automatically.
  • Set your job parameters in the software before scanning—resolution (usually 200 or 300 dpi), color or black-and-white mode, and whether to scan single or double-sided—so the scanner knows what to do when you press Start.
  • The scanner will pause and display an error code on the touchscreen if it jams, detects a double-feed, or runs out of paper; clear the jam, remove the extra sheet, or refill the hopper and press Resume to continue.
  • Images are saved to a folder on the connected computer or sent to a network location, and you can review them in the software to check for quality, missing pages, or upside-down scans before archiving or printing.
  • Clean the feed rollers and glass platen weekly with a lint-free cloth and approved cleaner to prevent jams and keep image quality consistent.

Preparing Paper and Loading the Hopper

Before you load anything, separate your stack into batches of 50 to 200 sheets, depending on the paper weight and condition. Remove any staples, paper clips, sticky notes, or tape—these cause jams and damage the scanner. If pages are folded, creased, or stuck together, unfold and separate them by hand. Damaged or very thin pages should be set aside and scanned separately or by hand if the Falcon cannot feed them reliably.

Tap the stack on a flat surface to align all edges, then place it in the hopper with the first page face-down. The top edge of the stack should point toward the feed rollers—the Falcon will pull from the top of the stack. Make sure the paper sits flat in the hopper and does not curl or tilt. If the hopper has side guides, adjust them so they touch the edges of your paper stack without squeezing it.

Check the output tray configuration. The Falcon can stack scanned originals in one tray or sort them into multiple trays based on rules you set in the software (for example, separate by color, by barcode, or by blank pages). Make sure the output trays are empty and positioned to catch paper without overflow. If you are using a sorter attachment, confirm it is seated correctly and the software knows it is there.

Configuring the Scanning Job in Software

Open the Opex ImageWare software or your capture process on the workstation. You will see a job setup screen where you define how the scanner should process your batch. The most common settings are resolution, color mode, and sides.

Resolution is measured in dots per inch (dpi). For most office documents, 200 dpi is sufficient and scans faster; 300 dpi gives sharper text and is standard for archival or legal documents. Do not use 600 dpi unless you are scanning photographs or fine detail—it slows the scanner and creates very large files. Color mode choices are usually black-and-white (fastest, smallest files), grayscale (for documents with shading or faint text), or color (for photos or colored forms). Choose black-and-white for standard business documents unless you need to preserve color.

Sides means whether to scan one side or both sides of each sheet. The Falcon has dual imaging heads, so it scans both sides in a single pass—selecting "duplex" or "both sides" does not slow it down compared to single-sided mode. If your originals are only printed on one side, you can still scan both sides; the blank side will be blank in the output. Some jobs require you to specify output format (TIFF, PDF, JPEG) and whether to save to a local folder, a network drive, or send to an email address or cloud service.

Once you have set all parameters, save the job with a clear name (for example, "Invoices_March_Batch1") so you can reuse it for similar batches later. The software will remember these settings and explore them when you press Start on the scanner.

Starting the Scan and Monitoring Progress

Load your paper stack into the hopper and close any access doors. On the scanner's touchscreen, select the job you just configured or confirm the default job settings. Press the Start button on the control panel. The Falcon will begin pulling sheets from the hopper one at a time, scanning both sides, and moving originals to the output tray.

The touchscreen displays a live page count and scanning speed (sheets per minute). Most Falcon models scan at 90 to 120 pages per minute, so a 500-page batch takes roughly 5 to 10 minutes depending on resolution and whether the scanner pauses for any reason. Do not open the hopper or touch the paper path while scanning is in progress—wait for the scanner to finish or press Pause if you need to stop.

If the scanner detects a problem, it will pause and display an error code. Common codes are jam (paper stuck in the feed path), double-feed (two sheets pulled at once), or hopper empty (no more paper). The touchscreen will tell you which one. Open the access door, clear the jam or remove the extra sheet, refill the hopper if needed, and press Resume on the control panel. The scanner will continue from where it stopped.

Checking Image Quality and Handling Problems

When the batch finishes scanning, the software displays the scanned images in a preview window. Scroll through the batch and look for common issues: upside-down pages, blank pages that should have content, pages that are too dark or too light, or pages that are missing entirely. If you find problems, you have a few options depending on what went wrong.

If a page is upside-down or rotated, most software lets you rotate it in the preview before saving. If a page is too dark or too light, you can rescan that page at a different brightness or contrast setting—remove it from the output stack, reload it into the hopper, and run a single-page job with adjusted settings. If pages are missing, check the output tray and the area around the scanner; sometimes a sheet falls to the side or gets stuck in a sorter. If a page truly did not scan, reload it and scan it again.

Blank pages in the output are usually intentional (the original was blank), but if you want the software to skip them automatically, look for a "blank page removal" or "blank page detection" option in the job settings. Some software can also detect and remove duplicate pages if the same sheet was scanned twice by accident.

Saving and Organizing Your Scanned Files

Once you have reviewed the images and confirmed quality, the software saves them to the location you specified in the job setup. Files are usually named automatically with a timestamp or batch number (for example, "Invoices_March_Batch1_001.tif", "Invoices_March_Batch1_002.tif") so you can identify which batch they came from and in what order they were scanned.

If you scanned in TIFF format, each page is a separate file. If you scanned to PDF, the software may have combined all pages into a single PDF file or created one PDF per page, depending on your settings. Check your software's output folder to see what was created. Move the files to your archive location, backup drive, or document management system according to your organization's procedures.

Keep the scanned originals in the output tray until you have confirmed that all images are readable and complete. Once you are satisfied, you can recycle or shred the paper according to your data retention and privacy policies.

Routine Maintenance to Keep the Scanner Running

The Falcon requires regular cleaning to prevent jams and maintain image quality. Weekly, use a lint-free cloth slightly dampened with approved scanner cleaner (or distilled water if cleaner is not available) to wipe the feed rollers, the separation pad, and the glass platen (the flat surface where pages pass under the imaging heads). Do not use paper towels, which leave lint; use microfiber cloths or lens paper instead. Let all surfaces dry completely before scanning again.

Check the hopper and output trays for debris, dust, or torn pieces of paper. If you notice frequent jams with a particular type of paper, that paper may be too thin, too thick, or too humid. Store paper in a dry location and let it acclimate to room temperature before scanning if it has been stored in a cold or damp area.

The Falcon has a maintenance counter that tracks how many pages have been scanned. When the counter reaches a certain number (usually 500,000 to 1,000,000 pages), the software will alert you that a service is due. At that point, contact Opex or an authorized service provider to replace wear parts such as rollers, separation pads, and imaging lamps. Ignoring maintenance alerts leads to poor image quality and more frequent jams.

Frequently Asked Questions

What should I do if the scanner keeps jamming on the same type of paper?

Check that the paper is not too thin, too thick, or curled. Separate the stack into smaller batches (50 sheets instead of 200) so there is less weight on the feed rollers. Wipe the feed rollers and separation pad with a damp lint-free cloth to remove dust or residue. If jams continue, the paper may not be suitable for automatic feeding; scan those pages by hand using a flatbed scanner or a different device.

Can I scan mixed paper sizes in one batch?

The Falcon is designed for uniform paper sizes within a batch. If you mix letter-size and legal-size sheets, the scanner may misalign or jam. Separate your originals by size and run each size as a separate job with the correct settings. Some Falcon models have auto-size detection, but it is more reliable to sort first.

Why are my scanned images coming out upside-down?

You loaded the paper face-up instead of face-down, or you loaded it with the top edge pointing away from the feed rollers. The Falcon expects the first page face-down with the top edge toward the scanner. Reload the stack correctly and rescan, or use the rotation tool in your software to flip the images before saving.

How do I know if the scanner needs cleaning?

If you notice streaks on scanned images, pages are not feeding smoothly, or the scanner is jamming more often than usual, it is time to clean. Even if you do not see obvious problems, clean the rollers and platen weekly as part of routine maintenance. A clean scanner runs faster and produces sharper images.

What file format should I use for long-term storage?

TIFF is the standard for archival scanning because it is uncompressed, widely supported, and does not degrade over time. PDF is good for sharing and viewing but uses compression that can affect image quality if you need to re-scan or enhance images later. Check your organization's document retention policy to see which format is required.