The Smartglow Exergen Temporal Scanner reads your temperature from your forehead in three seconds without touching your skin
The Smartglow Exergen is a non-contact infrared thermometer that measures the temperature of the temporal artery — the blood vessel that runs across your forehead. You point it at your forehead from about one inch away, press the button, and it displays your temperature on a small screen. No probe, no waiting, no discomfort. The scanner works on batteries and costs between $40 and $60 depending on where you buy it.
The device is designed for home use and works fastest on people over age three months. It is less accurate on infants under that age because their temporal arteries are harder to locate. The scanner stores your last eight readings in memory, which can be useful if you want to track a fever over a few hours.
Key Takeaways
- Hold the scanner one inch from the center of your forehead, press the button, and read the temperature on the screen within three seconds.
- The scanner works best on a dry forehead — sweat, hair, or hats can block the infrared signal and give a low reading.
- Replace the two AAA batteries when the low-battery symbol appears on the screen, usually after 3,000 to 5,000 readings.
- The device stores your last eight temperature readings, which you can scroll through using the memory button on the back.
Step-by-step: Taking a temperature with the Smartglow Exergen
Start with a clean, dry forehead. If you have been wearing a hat or have sweat on your skin, wipe your forehead with a dry cloth and wait 30 seconds. Sweat and moisture block the infrared beam and cause the scanner to read low.
Hold the scanner perpendicular to your forehead — that means straight on, not at an angle — about one inch away from the skin. Aim for the center of your forehead, between your eyebrows. Press and hold the button on the side of the device. You will hear a beep and see a number appear on the screen within two to three seconds. Release the button. The temperature will stay on the screen for about 10 seconds before it disappears.
If the screen shows "Lo" or "Hi," the reading is outside the device's range (below 50°F or above 104°F). A "Lo" reading usually means the forehead was too cold or the device was not held close enough. Try again after waiting a minute.
Why your reading might be wrong
The most common reason for a low reading is moisture or obstruction on the forehead. Sweat, lotion, makeup, or a wet cloth will scatter the infrared beam. Dry your forehead completely and wait at least 30 seconds before trying again. If you have just come inside from the cold, wait five minutes for your forehead to warm up to body temperature.
Holding the scanner too far away or at an angle also causes low readings. The beam needs to hit the temporal artery directly. Practice holding it exactly one inch away and pointing straight at your forehead. Some people find it easier to use a ruler the first time to get the distance right.
If the device is very cold — for example, if it has been sitting in a car in winter — let it warm to room temperature for 15 minutes before using it. A cold scanner can give inaccurate readings until it reaches the temperature of the room.
Checking and replacing the batteries
The Smartglow Exergen uses two AAA batteries. When the battery symbol appears on the screen, the batteries are running low and should be replaced within the next week. Do not wait until the device stops working.
To replace the batteries, locate the battery compartment on the back of the device. It is usually held closed by a small plastic tab or a screw. Slide the tab or unscrew the compartment, remove the old batteries, and insert two new AAA batteries with the positive end facing up. Close the compartment and press the button once to confirm the device is working.
If you replace the batteries and the screen still shows "Lo" or "Hi" for every reading, the device may need recalibration. Contact Exergen customer service — they can walk you through a reset or arrange a replacement if the device is still under warranty.
Using the memory function to track readings over time
The Smartglow Exergen stores your last eight temperature readings. To view them, press the memory button on the back of the device. The screen will show the most recent reading first, with the time elapsed since that reading (for example, "2 hours ago"). Press the memory button again to cycle through older readings.
This feature is useful if you are tracking a fever and want to see whether your temperature is going up, down, or staying the same. Write down the readings if you plan to share them with a doctor. The memory clears when you replace the batteries, so take notes before you do a battery swap if you need to keep a record.
Cleaning and storing your scanner
Wipe the lens on the front of the scanner with a soft, dry cloth once a week. Do not use water, alcohol, or cleaning solutions — they can damage the infrared sensor. If dust or debris gets stuck on the lens, use a dry cotton swab to gently remove it.
Store the scanner in a cool, dry place at room temperature. Do not leave it in direct sunlight, in a hot car, or in a damp bathroom. Extreme heat or humidity can shorten the life of the batteries and damage the sensor. Keep it in a drawer or a cabinet where it will stay at a steady temperature.
When to replace your Smartglow Exergen
The device usually lasts three to five years with normal home use. If you take 10 to 15 readings per day, you may need to replace it sooner. Signs that it is time for a new one include readings that are consistently off by more than one degree, a screen that does not light up even with fresh batteries, or a lens that has become cloudy or scratched.
Most retailers offer a one-year warranty on the Smartglow Exergen. If your device stops working within that time, contact the store where you bought it or reach out to Exergen directly with your receipt. They will either repair it or send you a replacement.
Frequently Asked Questions
Can I use the Smartglow Exergen on a baby?
The scanner works on infants over three months old, but it is less reliable on younger babies because their temporal arteries are harder to locate. For infants under three months, a rectal thermometer is more accurate. Always check with your pediatrician about which method to use for your child.
Does the scanner work if I have a headband or hat on?
No. The infrared beam cannot pass through fabric. Remove any headband, hat, or hair clip before taking a reading. Make sure your forehead is fully exposed and dry.
How accurate is the Smartglow Exergen compared to other thermometers?
Non-contact infrared thermometers are generally accurate within 0.5 to 1 degree Fahrenheit when used correctly. They are less precise than rectal thermometers but faster and less invasive. If you need a very precise reading for medical reasons, ask your doctor which type of thermometer they recommend.
What does it mean if the screen shows "Er"?
An "Er" message usually means the device detected an error in the reading. This can happen if you moved the scanner while the button was pressed or if the forehead was too wet. Wait 30 seconds, dry your forehead, and try again.
Can I use the scanner on someone else?
Yes. The scanner is non-contact, so there is no risk of spreading germs. Just make sure the other person's forehead is clean and dry, and hold the scanner the same way you would for yourself.