How the Exergen Temporal Scanner Works

The Exergen temporal scanner is a non-contact infrared thermometer that reads temperature from the temporal artery—the blood vessel that runs across the forehead just under the skin. You hold the device about half an inch away from the forehead and press the button. The scanner measures infrared heat radiating from that artery and displays the temperature on a small screen in about one second. No probe goes in the ear or mouth, and the person being measured does not have to hold still for long.

The device works because the temporal artery is close enough to the skin surface that an infrared sensor can detect its heat accurately. The scanner's software is calibrated to convert that infrared reading into a core body temperature—the temperature inside the body, not just the skin surface. This is why the temporal scanner is considered more reliable than a forehead strip thermometer, which only measures skin temperature.

Key Takeaways

  • Hold the scanner about half an inch from the center of the forehead, press the button, and read the temperature in one second.
  • Wipe the sensor lens with a clean, dry cloth before each use to remove dust or moisture that can block the infrared reading.
  • Do not use the scanner on a forehead that is wet with sweat or covered by hair; dry the skin first or brush hair away.
  • Replace batteries when the low-battery indicator appears on the screen, and check the manual for the correct battery type for your model.

Positioning the Scanner Correctly

The most common mistake is holding the scanner too far away or at the wrong angle. Position the device so the sensor lens points straight at the center of the forehead, about half an inch away. Some models have a small target light or guide to help you aim. If your model has a guide, align it with the center of the forehead between the eyebrows.

Make sure the person's forehead is dry and free of hair. If sweat or moisture covers the skin, the infrared reading will be inaccurate because water absorbs heat differently than skin does. If hair is hanging over the forehead, brush it away. Wait a few minutes after the person has been in direct sunlight, near a heater, or wearing a hat, because the forehead skin temperature may not yet match core body temperature.

Cleaning the Sensor Lens

The infrared sensor lens is the small window on the front of the scanner. Dust, fingerprints, or dried sweat on this lens will block or scatter the infrared signal, leading to a reading that is too low. Before each use, wipe the lens gently with a clean, dry, lint-free cloth. Do not use water, alcohol, or cleaning solutions unless the manual specifically says they are safe for your model.

If the lens has dried residue that does not wipe away easily, dampen the cloth very slightly with distilled water, wipe the lens, and then dry it when ready with a second dry cloth. Never let liquid drip into the device or soak the lens. Store the scanner in a clean, dry place where dust will not settle on the exposed lens.

Reading and Recording the Temperature

Most Exergen temporal scanners display the temperature in large numbers on a small LCD screen. The reading appears within one second of pressing the button. Some models show the temperature in Fahrenheit, others in Celsius, and some can switch between the two—check your manual to see how to change the display if needed.

Write down the temperature and the time you took it, especially if you are monitoring someone's fever over several hours or days. Note whether the person had just eaten, exercised, or been in a warm or cold environment, because these factors can affect the reading slightly. If the temperature seems unusually high or low compared to how the person feels, take it again after cleaning the lens and repositioning the scanner.

Troubleshooting Common Problems

If the scanner shows "Lo" or "Hi" on the screen, the temperature is outside the device's range. Most models read between 50°F and 108°F (10°C and 42°C). If you see "Lo" and the person is alive and conscious, the scanner may not be positioned correctly or the lens may be dirty. Clean the lens, reposition the device, and try again.

If the screen is blank or does not light up, check that the batteries are installed correctly and have not run out. Consult the manual for the battery compartment location and the correct battery type. If the batteries are fresh and correctly installed but the screen still does not light, the device may need repair or replacement.

If the reading seems too low compared to how the person feels, the forehead may be wet or cool. Dry the skin, wait a minute, and try again. If readings are consistently lower than expected, the lens may need cleaning even if it looks clear to the eye.

Battery Replacement and Storage

Most Exergen temporal scanners use two or four AA or AAA batteries, depending on the model. When the low-battery indicator appears on the screen—usually a small battery symbol or warning message—replace the batteries promptly. Do not wait until the device stops working, because the reading may become inaccurate as voltage drops.

Open the battery compartment according to your manual's instructions, remove the old batteries, and insert new ones with the positive and negative ends facing the correct direction. Close the compartment securely. Store the scanner in a cool, dry place away from direct sunlight, heat sources, and moisture. If you will not use it for several months, remove the batteries to prevent corrosion inside the device.

When to Call the Manufacturer

If the scanner consistently gives readings that do not match how the person feels or how other thermometers read, contact the manufacturer's customer service. Exergen provides phone support and can walk you through additional troubleshooting steps. If the device is still under warranty, they may replace it at no cost.

Do not attempt to open the device yourself or use compressed air to clean the internal lens, because you may damage the infrared sensor. If the lens is scratched or the device has been dropped, the sensor may no longer be accurate, and repair or replacement is the only option.

Frequently Asked Questions

Can I use the temporal scanner on a baby or small child?

Yes, the temporal scanner is safe for infants and children because it does not require inserting anything into the ear or mouth. Position it on the forehead the same way you would for an adult. Babies' foreheads are smaller, so aim for the center area between the eyebrows. If the child is crying or has just been in a warm room, wait a minute before taking the temperature.

Why does the scanner give a different reading than an ear thermometer?

Ear thermometers measure infrared heat from the eardrum, while temporal scanners measure heat from the forehead artery. Both are designed to estimate core body temperature, but they use different sites and calibrations. A difference of 0.5°F to 1°F between the two is normal. If the difference is larger, check that both devices are clean and that you are positioning each one correctly.

Is the temporal scanner accurate for people with dark or light skin?

The temporal scanner measures infrared heat, not skin color, so skin tone does not affect accuracy. The infrared sensor detects heat radiating from the temporal artery beneath the skin surface. Accuracy depends on a clean lens, correct positioning, and a dry forehead—not on the person's appearance.

Can I use the scanner through a window or plastic barrier?

No. Glass, plastic, and other transparent materials block or scatter infrared radiation. You must position the scanner directly against the skin or within the recommended distance from bare skin. If infection control is a concern, wipe the lens with a clean cloth between uses rather than trying to use the scanner through a barrier.

What should I do if the forehead is too wet or dirty to get an accurate reading?

Gently pat the forehead dry with a clean cloth and wait a minute for the skin temperature to stabilize. If the person has been sweating heavily, wait a few minutes in a cool environment before taking the temperature. If the forehead is visibly dirty, wash it gently with a damp cloth, dry it thoroughly, and then take the reading.