LiDAR works best when mounted high and pointed straight down at the ground

A LiDAR scanner detects buried structures by bouncing laser pulses into the earth and measuring what bounces back. To map a buried city, you need the scanner positioned where it can "see" the largest area with the clearest signal. That means mounting it as high as possible and aiming it downward at the ground you want to scan.

The height and angle matter because LiDAR's laser beam spreads as it travels. A scanner mounted 100 feet up covers a wider ground area than one at 20 feet, and the signal penetrates soil more effectively when the beam hits nearly perpendicular to the surface. If you tilt the scanner at a shallow angle, the beam spreads across a larger area but loses depth penetration into the earth.

The type of LiDAR system you use—airborne, drone-mounted, or ground-based—determines where installation is practical. Each has different mounting heights, coverage speeds, and soil-penetration capabilities.

Key Takeaways

  • Airborne LiDAR mounted on aircraft or helicopters covers large areas quickly but requires professional operation and is expensive for small sites.
  • Drone-mounted LiDAR systems offer flexibility and lower cost than airborne options, though they cover smaller areas per flight and require line-of-sight operation.
  • Ground-based LiDAR systems mounted on vehicles or tripods work best for detailed mapping of specific locations and can penetrate soil more deeply than airborne systems.
  • The scanner should be positioned perpendicular to the ground surface and high enough to avoid obstacles like trees and buildings that block the laser signal.
  • Soil composition, moisture content, and vegetation cover affect how well LiDAR penetrates to buried structures, so site conditions matter as much as scanner placement.

Airborne LiDAR mounted on aircraft or helicopters

Airborne LiDAR systems are flown at altitudes between 1,000 and 10,000 feet, depending on the resolution needed and the area to be covered. At these heights, a single flight pass can map hundreds of square miles. The scanner is mounted on the aircraft's belly or side and points downward at a slight angle, allowing the plane's forward motion to build a complete map as it flies.

This approach works well for mapping large buried cities or archaeological sites spread across many square miles. The high altitude means the laser beam covers a wide swath of ground, and the speed of the aircraft lets you collect data quickly. However, airborne LiDAR requires hiring a specialized survey company with aircraft and trained operators, which is expensive—typically thousands of dollars per flight hour.

Airborne systems also struggle with dense vegetation. If trees or thick brush cover the site, the laser may not penetrate to the ground beneath. In tropical or heavily forested regions, you may need to clear vegetation first or use a different scanning method.

Drone-mounted LiDAR for smaller or difficult-to-reach sites

A drone-mounted LiDAR scanner is attached to a multirotor or fixed-wing drone and flown at altitudes between 100 and 500 feet. At these lower heights, the scanner produces higher-resolution maps than airborne systems and can focus on specific areas without covering unnecessary ground. Drones are cheaper to operate than aircraft and do not require airfield access.

Drone LiDAR works well for buried cities in remote locations, dense forests, or areas where airborne access is restricted. You can fly multiple passes over the same site to build a detailed 3D model of subsurface features. The main limitation is flight time—most drones carry a LiDAR scanner for 20 to 45 minutes before the battery depletes, so large sites require multiple flights.

Drone operation also requires clear line of sight and good weather. Wind, rain, and low visibility ground the aircraft. In areas with dense canopy, the drone must fly lower to penetrate vegetation, which reduces the area covered per flight and increases the total time needed to map the site.

Ground-based LiDAR systems for detailed mapping

Ground-based LiDAR scanners are mounted on tripods, vehicles, or handheld rigs and positioned at ground level or on low platforms. These systems excel at penetrating soil because the laser beam travels a shorter distance through air before entering the earth, and the signal is not scattered by atmospheric particles the way airborne signals are.

A ground-based scanner can be moved to different positions around a site to build a complete 3D map of buried structures. This method is slower than airborne or drone scanning—covering a large area takes days or weeks instead of hours—but the data quality is often superior, especially in areas with complex subsurface geometry or multiple overlapping structures.

Ground-based systems are also the only option in places where airborne or drone access is impossible: inside caves, under dense forest canopy, or in urban areas where flying is restricted. You can position the scanner directly above the area of interest and adjust the angle and height to optimize signal penetration.

Positioning the scanner perpendicular to the ground surface

Regardless of the mounting platform, the scanner should point as close to straight down as possible. When the laser beam hits the ground at a steep angle (close to perpendicular), it penetrates soil more effectively and produces clearer reflections of buried structures. A shallow angle spreads the beam across a larger area but weakens the signal returning from depth.

On an aircraft or drone, this means the scanner is mounted on a gimbal or fixed bracket that keeps it pointed downward as the platform moves. On a ground-based system, you adjust the tripod or vehicle position so the scanner faces the target area directly. If the terrain is sloped, you may need to reposition the scanner multiple times to maintain perpendicularity across the entire site.

Obstacles also affect positioning. Trees, buildings, power lines, and other structures block the laser beam. Before installing the scanner, survey the site for obstacles and choose a mounting location that has a clear line of sight to the ground you want to scan.

How soil composition affects scanner placement

LiDAR penetration depth depends heavily on soil type and moisture. Sandy or dry soil allows the laser to penetrate deeper than clay or wet soil. In wet conditions, the signal is absorbed quickly and may not reach buried structures more than a few feet down. This means your scanner placement strategy should account for local soil conditions.

In areas with shallow water tables or recent rainfall, you may need to mount the scanner lower and closer to the target area to maximize penetration. In dry, sandy regions, you can operate from greater heights and still detect structures several meters below the surface. Before planning your scan, research the site's geology and recent weather to estimate how deep the LiDAR signal will travel.

Vegetation also affects results. Dense grass, shrubs, or trees scatter the laser signal and reduce penetration. If the site is heavily vegetated, you may need to clear some cover or use a ground-based scanner positioned lower to the soil surface.

Combining multiple scanner positions for complete coverage

Large buried cities often require scanning from multiple positions to capture all structures and avoid shadows or blind spots. A shadow occurs when a tall buried feature blocks the laser signal from reaching structures behind it. By scanning from different angles and heights, you build a complete 3D model that shows all subsurface features.

For airborne systems, this means flying multiple passes over the site in different directions. For drone systems, you fly several missions at different altitudes or angles. For ground-based systems, you move the scanner to different locations around the perimeter and center of the site. Each scan is processed and combined into a single map using specialized software.

Planning multiple scans takes more time and money, but it produces the most accurate and complete picture of buried structures. Start with a single scan to identify major features, then plan additional scans to fill gaps and confirm findings.

Frequently Asked Questions

Can LiDAR see through solid rock or stone walls?

LiDAR cannot penetrate solid rock, but it can detect the boundaries of stone structures buried in soil. The laser bounces off the surface of the stone and returns a signal showing the structure's outline and depth. Dense stone walls block deeper penetration, so structures buried beneath them may not be visible.

How deep can LiDAR detect buried structures?

Penetration depth varies by soil type and moisture. In dry sand, LiDAR may detect structures 10 to 20 feet deep. In wet clay or soil with high mineral content, penetration may be only 3 to 5 feet. Ground-based systems penetrate deeper than airborne systems because the signal travels a shorter distance through air before entering soil.

What is the best time of year to scan a buried city?

Dry seasons are best because wet soil absorbs the laser signal more quickly. Scan after a period of dry weather when soil moisture is low. Avoid scanning during or when ready after heavy rain. In tropical regions, the dry season may be only a few months long, so plan scans accordingly.

Do I need to clear vegetation before scanning?

Dense vegetation reduces LiDAR penetration, but light grass and small shrubs do not always require clearing. Airborne and drone systems can often see through sparse vegetation. Ground-based systems work better with cleared ground. Test a small area first to see whether vegetation is blocking the signal before committing to large-scale clearing.

Can LiDAR distinguish between different types of buried structures?

LiDAR shows the shape and depth of buried features but not their material composition. You cannot tell from LiDAR alone whether a structure is stone, brick, or packed earth. Ground-truthing—excavating test pits to confirm what the LiDAR detected—is necessary to identify structure types and confirm findings.