Samsung rear speakers connect to your soundbar through a wireless pairing process that usually takes under five minutes
Most Samsung soundbars with rear speaker compatibility use a dedicated wireless connection—not Bluetooth or Wi-Fi, but a proprietary Samsung protocol. The speakers and soundbar communicate on their own closed network, which keeps the signal stable and reduces interference from other devices in your home. The pairing happens once during setup, and after that the rear speakers stay connected whenever both devices are powered on.
The exact steps depend on your soundbar model, but the general process is the same: put the soundbar in pairing mode, then put the rear speakers in pairing mode, and they find each other automatically. You do not need a remote, an app, or a network connection to make this work—just power and proximity.
Key Takeaways
- Samsung rear speakers pair wirelessly using Samsung's proprietary protocol, not Bluetooth, so they stay connected even if your phone leaves the room.
- The pairing process requires you to hold a button on the soundbar for a few seconds, then hold a button on each rear speaker, usually in that order.
- Both devices must be powered on and within 10 to 15 feet of each other during pairing, though they can be farther apart once the connection is established.
- If pairing fails, reset both devices by unplugging them for 30 seconds, then try again—this solves most connection problems without calling support.
Locate the pairing buttons on your soundbar and rear speakers
The pairing button on your soundbar is usually on the back panel or the bottom edge. Look for a small button labeled ID Set, Pairing, or Wireless—some models call it something slightly different. If you cannot find it on the device itself, check the manual that came in the box or search your soundbar model number plus "pairing button" online.
The rear speakers have a similar button, usually on the back or underside. On some Samsung models, it is a recessed button you press with a paperclip or pen tip. On others, it is a larger button you can press with your finger. The manual will show you exactly where it is on your specific model.
Put your soundbar into pairing mode first
Power on the soundbar and wait for it to fully boot—usually 10 to 15 seconds. Then press and hold the pairing button on the soundbar for 5 to 10 seconds. You should see a light on the soundbar begin to blink, usually blue or white. This blinking light means the soundbar is now in pairing mode and listening for rear speakers.
Leave the soundbar in this state while you move to the rear speakers. The pairing mode window usually stays open for about 2 to 3 minutes, so you have time to walk to the other room without rushing.
Put each rear speaker into pairing mode
Power on the first rear speaker and wait a few seconds for it to boot. Then press and hold its pairing button for 5 to 10 seconds, just as you did with the soundbar. The rear speaker's light should begin to blink, indicating it is searching for a soundbar to pair with.
Within a few seconds, the rear speaker should find the soundbar and connect automatically. The blinking light will usually become solid or change color to show the connection is complete. Repeat this process with the second rear speaker if you have a pair. Each speaker pairs individually, so you may need to do this twice if your system includes two rear speakers.
Verify the connection is complete
Once both rear speakers are paired, all three devices should show solid lights (not blinking). Play a test sound through your soundbar—a movie scene with surround effects works well—and listen to whether sound comes from the rear speakers. If you hear audio from behind you, the pairing was successful.
If the rear speakers do not produce sound, check that they are turned on and that the soundbar's surround speaker setting is enabled in its menu. Some soundbars require you to turn on surround speakers in the settings even after pairing is complete. Consult your soundbar's manual for the exact menu path.
Reset the devices if pairing fails
If the rear speakers do not connect after you follow the pairing steps, unplug both the soundbar and rear speakers from power for 30 seconds. Plug them back in and wait for them to fully boot. Then repeat the pairing process from the beginning—this time starting with the soundbar first, then the rear speakers.
If pairing still fails after a reset, check that both devices are within 10 to 15 feet of each other during the pairing process. Walls and metal objects can weaken the signal, so try pairing in an open area if possible. If you continue to have trouble, your soundbar or rear speakers may have a hardware issue, and you should contact Samsung support with your model number and serial number.
Troubleshoot common connection problems
If the rear speakers pair successfully but then disconnect randomly, the devices may be too far apart or there may be interference from a microwave, cordless phone, or wireless router. Try moving the soundbar and rear speakers closer together, or move the router away from the entertainment area. You can also try repositioning the rear speakers to a different shelf or wall location.
If the rear speakers are paired but produce no sound, check your soundbar's audio settings. Some models have a separate "surround speaker" or "rear speaker" toggle that must be turned on in the menu, even after successful pairing. Check the manual for your specific model to find this setting. If the setting is already on, try unplugging the rear speakers for 30 seconds and plugging them back in—this refreshes the connection without erasing the pairing.
Frequently Asked Questions
Do I need to use the Samsung SmartThings app to pair the rear speakers?
No. The wireless pairing between the soundbar and rear speakers happens without any app or network connection. The SmartThings app can control your soundbar's volume and input, but it is not required for the rear speakers to work. Pairing is done entirely through the physical buttons on the devices.
Can I pair the rear speakers if my soundbar is connected to a TV with HDMI?
Yes. The HDMI connection to your TV does not interfere with the wireless pairing between the soundbar and rear speakers. Pair them first, then connect the soundbar to your TV. The rear speakers will continue to work normally.
What if I only have one rear speaker instead of a pair?
You can pair a single rear speaker to your soundbar, and it will work. However, most Samsung soundbars are designed to use a pair of rear speakers for proper surround sound. With only one speaker, you will hear surround effects from only one side of the room. If possible, adding a second matching rear speaker will give you the full surround experience.
How far apart can the soundbar and rear speakers be once they are paired?
Once paired, the rear speakers can typically be 30 to 50 feet away from the soundbar, depending on your model and whether there are walls between them. Check your manual for the exact range, as it varies by soundbar model. During the initial pairing, keep them within 10 to 15 feet for the best chance of a successful connection.
Will I lose the pairing if I unplug the soundbar or rear speakers?
No. The pairing is stored in the devices' memory, so unplugging them will not erase it. When you plug them back in, they will reconnect automatically as long as they are powered on and within range. You only need to pair them once, unless you factory reset one of the devices.