The three ways to connect a soundbar to a projector
A projector and soundbar rarely connect directly to each other. Instead, the soundbar pulls audio from the same source your projector displays — a streaming device, Blu-ray player, game console, or computer. The connection method depends on what audio output your projector has and what inputs your soundbar accepts.
Most projectors output audio through HDMI, optical (Toslink), or a 3.5mm headphone jack. Most soundbars accept HDMI, optical, or both. The best route is usually optical, because it works with nearly every projector and soundbar combination, requires only one cable, and avoids the audio delay problems that sometimes happen with HDMI.
If your projector has no optical port, HDMI is the next choice. If neither works, a 3.5mm cable from the projector's headphone jack to the soundbar's auxiliary input will work, though this is the least reliable method and may require manual volume adjustment on both devices.
Key Takeaways
- Optical (Toslink) cable is the most reliable connection method for most projector and soundbar pairs because it carries audio only and avoids sync delays.
- Check your projector's audio outputs (usually on the back panel) and your soundbar's audio inputs (usually on the rear or side) before buying a cable.
- HDMI can work but sometimes causes audio to lag behind the picture; if this happens, your soundbar's settings menu usually has a delay adjustment.
- A 3.5mm cable from the projector's headphone jack works as a last resort but requires you to control volume on both devices separately.
Using an optical cable (the most common setup)
Look at the back of your projector for a port labeled "Optical Out," "Toslink," or "S/PDIF." It is a small square opening, usually black or red. If you see it, this is your best option. Optical cables carry audio signals as light pulses and work with nearly every soundbar.
Plug one end of the optical cable into the projector's optical output port. Plug the other end into the optical input on your soundbar — this is usually on the back panel, sometimes labeled "Optical In" or "S/PDIF In." The cable only fits one way, so do not force it.
Turn on the projector and soundbar. Go into your soundbar's settings menu (usually accessed with a button on the remote or the soundbar itself) and set the input to "Optical" or "Toslink." The soundbar should now play audio from whatever your projector is displaying. If you hear nothing, check that the optical cable is fully seated in both ports and that the soundbar is not muted.
Using HDMI when optical is not available
If your projector has no optical port, check for an HDMI port labeled "HDMI Out" or "HDMI ARC" (Audio Return Channel). Not all projectors have this — many have only HDMI inputs. If your projector has HDMI output, you can run an HDMI cable from the projector to an HDMI input on your soundbar.
Plug the HDMI cable into the projector's HDMI output port and into any HDMI input on the soundbar. Turn on both devices and set the soundbar's input to HDMI. The soundbar should recognize the audio signal automatically.
HDMI sometimes causes audio to play slightly after the picture moves — this is called lip-sync delay. If you notice this, enter your soundbar's settings menu and look for an option called "Delay," "Lip Sync," or "Audio Delay." Increase this value in small steps (usually 50 to 100 milliseconds at a time) until the sound and picture line up. Every soundbar's menu is different, so check your manual if you cannot find this setting.
Using a 3.5mm cable as a backup option
If your projector has neither optical nor HDMI output, look for a 3.5mm headphone jack on the back or side panel. This is a small round port, usually labeled "Audio Out," "Headphone," or "Line Out." Many projectors have this even when they lack optical.
Plug a 3.5mm cable into the projector's headphone jack and into the "Aux In" or "Line In" port on your soundbar. Set the soundbar's input to "Aux" or "Line." The soundbar should now play audio from the projector.
This method requires you to control volume separately on both the projector and the soundbar, which is inconvenient. If the sound is too quiet, raise the volume on the projector first, then adjust the soundbar if needed. If the sound is distorted, lower the projector's volume and raise the soundbar's instead.
Checking your projector's audio output ports
Before you buy a cable, locate your projector's audio outputs. Most projectors have these ports on the back panel, sometimes in a cluster with video and power connections. Consult your projector's manual or look at the manufacturer's website if you are unsure which port is which.
Write down which ports your projector has: optical, HDMI output, 3.5mm headphone jack, or some combination. Then check your soundbar's manual or the back panel to see which inputs it has. Match them up — if both have optical, buy an optical cable. If only HDMI matches, buy an HDMI cable. If only 3.5mm matches, buy a 3.5mm cable.
Do not assume your projector has a particular port just because it is a certain brand or price. Even expensive projectors sometimes lack optical output. Checking first saves you a return trip to the store.
Troubleshooting when you hear no sound
If you have connected the cable correctly but hear nothing, start with the simplest checks. Make sure the soundbar is powered on and not muted — look for a mute button on the remote or the soundbar itself. Check that the volume on the soundbar is turned up, not at zero.
Next, verify that the soundbar's input is set to the correct source. If you used an optical cable, the input should be set to "Optical" or "Toslink." If you used HDMI, it should be set to "HDMI." If you used 3.5mm, it should be set to "Aux" or "Line." Many soundbars cycle through inputs with a button on the remote — press it until you see the correct input displayed.
If the soundbar still produces no sound, disconnect the cable from both ends and reconnect it firmly. Optical cables are especially sensitive to loose connections. If the cable is damaged or bent, replace it. If you have tried all of this and still hear nothing, the projector's audio output may be disabled in its settings menu — check the projector's manual for how to enable audio output.
Controlling volume and settings
When you use an optical or HDMI connection, the soundbar usually responds to its own remote control for volume and input selection. The projector's volume controls may not affect the soundbar at all — this is normal. Use the soundbar's remote to adjust volume.
If you used a 3.5mm cable, you may need to adjust volume on both devices. Start by setting the projector's volume to about 75 percent, then use the soundbar's remote to fine-tune from there. This prevents distortion that can happen if the projector sends too strong a signal to the soundbar.
Most soundbars have a settings menu accessible through their remote. This is where you can adjust delay, change the input source, or enable features like night mode (which compresses loud sounds so you do not disturb others). Spend a few minutes exploring these settings to get the sound the way you want it.
Frequently Asked Questions
Can I connect a soundbar directly to a projector with one cable?
Yes, if both devices have matching ports. An optical cable is the most common single-cable solution. HDMI also works as a single cable if your projector has HDMI output. A 3.5mm cable works too, though it is less reliable and requires separate volume control on both devices.
Why is there a delay between the sound and picture?
HDMI connections sometimes cause this, called lip-sync delay. Most soundbars have a delay adjustment in their settings menu — look for "Lip Sync," "Delay," or "Audio Delay" and increase it in small steps until the sound and picture line up. Optical cables rarely have this problem.
What if my projector has no audio outputs at all?
Some budget projectors lack audio outputs and send sound only through their built-in speaker. In this case, you cannot connect an external soundbar to the projector itself. Instead, connect the soundbar to whatever device feeds the projector — the streaming device, Blu-ray player, or game console — using that device's audio outputs.
Do I need a special cable or will any optical cable work?
Any optical (Toslink) cable works with any projector and soundbar that have optical ports. They are inexpensive and widely available. The same is true for HDMI and 3.5mm cables — there is no special "projector" version. Buy the standard version for your connection type.
Can I use both the projector's speaker and the soundbar at the same time?
Most projectors automatically disable their built-in speaker when you connect an external audio output. If both are playing, go into the projector's settings menu and look for an option to disable the internal speaker or set audio output to external only. Consult your projector's manual for the exact steps.