Most soundbars work with your TV remote through HDMI-CEC, a built-in connection standard
Your TV remote can control your soundbar without any setup if both devices support HDMI-CEC (Consumer Electronics Control). This is a feature built into most modern TVs and soundbars that lets them communicate over the same HDMI cable. When you press volume up or down on your TV remote, the signal travels through HDMI to the soundbar, which adjusts its volume automatically.
HDMI-CEC works only if your soundbar is connected to your TV with an HDMI cable — not an optical or 3.5mm audio cable. The soundbar must be plugged into an HDMI port on your TV that supports CEC (usually labeled ARC or eARC). Your TV remote does not need to be reprogrammed; the connection happens automatically once both devices are powered on and properly connected.
If your soundbar and TV both have HDMI-CEC but it is not working, the feature may be turned off in your TV's settings. Check your TV's menu under names like "HDMI-CEC", "Anynet+", "Bravia Sync", "EasyLink", or "SimpLink" — the exact name depends on your TV brand. Turn this setting on, power cycle both devices, and try again.
Key Takeaways
- HDMI-CEC lets your TV remote control soundbar volume automatically if both devices support it and are connected via HDMI.
- Your soundbar must be plugged into an HDMI ARC or eARC port on your TV for HDMI-CEC to work.
- If HDMI-CEC is not working, check your TV's settings menu and enable the feature — it may be called Anynet+, Bravia Sync, EasyLink, or SimpLink depending on your TV brand.
- If your soundbar uses an optical or 3.5mm cable instead of HDMI, you will need to use a separate remote or program your TV remote manually.
Check which HDMI port your soundbar is connected to
Not every HDMI port on your TV supports CEC. Most TVs have one or two ports labeled ARC (Audio Return Channel) or eARC (enhanced Audio Return Channel) — these are the ports that allow two-way communication. Your soundbar should be plugged into one of these ports, not into a regular HDMI input.
If your soundbar is connected to a regular HDMI port, move it to the ARC or eARC port. You may need to unplug and replug the cable. Once it is in the correct port, power off both the TV and soundbar completely, wait 30 seconds, and turn them back on. This full restart often fixes HDMI-CEC problems that appear after a connection change.
Enable HDMI-CEC in your TV's settings
The setting name varies by TV manufacturer. On Samsung TVs, it is called Anynet+ and is found under Settings > System > Anynet+ (HDMI-CEC). On Sony TVs, look for Bravia Sync under Settings > External Inputs > HDMI Signal Format. LG TVs use EasyLink under Settings > Sound > EasyLink. Panasonic calls it Viera Link, and Philips uses EasyLink as well.
Once you find the setting in your TV's menu, make sure it is turned on. Some TVs have this enabled by default, but others ship with it off. After you turn it on, restart both devices. If your TV remote still does not control the soundbar volume, check whether your soundbar also has a CEC setting that needs to be enabled — consult your soundbar's manual or the manufacturer's website.
Program your TV remote manually if HDMI-CEC is not an option
If your soundbar uses an optical or 3.5mm audio cable instead of HDMI, or if HDMI-CEC straightforward will not work, you can program your TV remote to send volume commands directly to the soundbar. This requires your TV remote to support learning mode — a feature that lets it record infrared signals from another remote.
First, find your soundbar's original remote. Put your TV remote into learning mode (check your TV remote's manual for the exact button combination — it is often a combination like holding Setup and pressing a number). Point the soundbar remote at your TV remote and press the volume up button on the soundbar remote. Your TV remote will record that signal. Repeat for volume down and mute. Now your TV remote can control the soundbar volume directly, even without HDMI-CEC.
If your TV remote does not have learning mode, you can purchase a universal remote that does. Universal remotes like the Logitech Harmony or GE Enbrighten can be programmed to control both your TV and soundbar from a single device. These remotes connect to your home network or use infrared signals to communicate with both devices.
Use your soundbar's own remote if TV control is not working
If you cannot get your TV remote to work with your soundbar, your soundbar's original remote will always work. Most soundbars come with a dedicated remote that controls volume, input selection, and sound modes. Keep this remote in an accessible place as a backup.
Some soundbars also have physical buttons on the unit itself — usually a power button and volume controls on the side or back. You can adjust volume using these buttons if you cannot locate the remote. Check your soundbar's manual to see which buttons do what.
Troubleshoot when your TV remote stops controlling the soundbar
If your TV remote was controlling the soundbar but suddenly stopped, the HDMI-CEC connection may have been interrupted. Power cycle both devices: turn off the TV, turn off the soundbar, wait 30 seconds, and turn them back on in that order. This resets the HDMI-CEC handshake and often restores control.
If power cycling does not work, check whether a TV software update disabled HDMI-CEC. Go back into your TV's settings and confirm the CEC feature is still enabled. Some TV updates reset this setting to off. You may also need to unplug the HDMI cable from both the TV and soundbar, wait 10 seconds, and plug it back in firmly — a loose connection can break HDMI-CEC communication.
If the soundbar remote still works but the TV remote does not, the problem is likely with your TV's CEC implementation rather than the soundbar. Try a different HDMI cable to rule out a damaged cable, or contact your TV manufacturer's support line if the issue persists.
Frequently Asked Questions
Do I need to reprogram my TV remote to control the soundbar?
No, if both devices support HDMI-CEC and are properly connected via HDMI ARC or eARC, the connection is automatic. Your TV remote will control the soundbar without any setup. If you are using learning mode on a universal remote, you will need to record the soundbar remote's signals once, but your TV remote itself does not need reprogramming.
Why does my TV remote control the soundbar volume but not the input?
HDMI-CEC typically only passes volume and power commands, not input selection. To switch the soundbar's input, use the soundbar's own remote or the physical buttons on the soundbar itself. Some universal remotes can be programmed to send input commands, but standard TV remotes cannot.
Can I control my soundbar with my TV remote if they are different brands?
Yes, HDMI-CEC is a standard that works across brands. A Samsung TV can control an LG soundbar, or a Sony TV can control a Bose soundbar, as long as both devices support HDMI-CEC and are connected via HDMI ARC or eARC. The brand does not matter.
What if my TV does not have an HDMI ARC port?
Older TVs may not have ARC or eARC ports. In that case, HDMI-CEC will not work. You will need to use your soundbar's own remote, or purchase a universal remote that can be programmed to control both devices using infrared signals.
Does HDMI-CEC work with wireless soundbars?
No, wireless soundbars that connect via Bluetooth or Wi-Fi cannot use HDMI-CEC because they are not connected to your TV with an HDMI cable. You must use the soundbar's own remote or a universal remote programmed in learning mode.