Mounting a soundbar takes 30 minutes and three tools
A soundbar hangs on the wall using a bracket that screws into wall studs or uses heavy-duty anchors if studs are not where you need them. You will need a drill or screwdriver, a level, and a stud finder (or a way to locate studs by tapping). Most soundbars come with a mounting bracket in the box, but if yours did not, you can buy a universal bracket for $15 to $40. The bracket attaches to the back of the soundbar first, then the bracket screws to the wall.
The whole job is straightforward if you follow the order: find studs, mark the holes, drill pilot holes, screw the bracket to the wall, then attach the soundbar. The most common mistake is hanging the soundbar too high—it should be at ear level when you are sitting down, not at eye level when standing. If you get the height wrong, the sound will bounce over your head instead of reaching your ears.
Key Takeaways
- A soundbar should hang at ear level when seated, usually 12 to 18 inches below your TV, not centered on the wall above it.
- Use a stud finder to locate wall studs and screw into them whenever possible, because drywall anchors alone may not hold a heavy soundbar long-term.
- Attach the mounting bracket to the soundbar first, then hold the bracket against the wall, mark the holes, and drill pilot holes before screwing in.
- A level ensures the soundbar sits straight, which matters both for appearance and for how the sound projects into the room.
Locate the studs in your wall
Use a stud finder to scan the wall where you want to hang the soundbar. Run it horizontally across the wall and mark the center of each stud with a pencil. Studs are usually 16 inches apart. If you do not have a stud finder, tap the wall with your knuckles—a solid sound means a stud is there, a hollow sound means empty space.
Most soundbars are 30 to 50 inches wide, so you will likely find at least one stud within that span. If no studs line up with your bracket holes, you can use heavy-duty drywall anchors rated for 25 pounds or more, but studs are always the stronger choice. Mark the stud locations on the wall with a pencil so you can see them when you hold the bracket in place.
Measure and mark the bracket height
Hold the soundbar bracket against the wall at ear level when you are sitting on your couch. This is usually 12 to 18 inches below the bottom of your TV, depending on how high your TV is mounted and how far back your seating is. Use a level to make sure the bracket is perfectly horizontal before you mark anything.
Once the bracket is level and at the right height, use a pencil to mark the center of each screw hole on the wall. Do not mark the holes while the bracket is tilted—tilt causes the marks to be off by an inch or more. Step back and look at the marks. They should form a straight line across the wall.
Drill pilot holes and attach the bracket
Drill a pilot hole at each mark you made. A pilot hole is a small hole (usually 1/8 inch) that guides the screw and prevents the wall from cracking. If you are drilling into a stud, use a bit slightly smaller than your screw. If you are drilling into drywall, use a bit that matches the size of your drywall anchor.
Insert drywall anchors into the holes if you are not screwing into studs, then screw the bracket to the wall. Tighten each screw firmly but do not over-tighten—you want the bracket snug against the wall, not so tight that you strip the hole. If the bracket shifts while you are tightening, hold it steady with your other hand or have someone else hold it.
Attach the soundbar to the bracket
Most soundbars have a mounting plate on the back with threaded holes or slots. Align the bracket arms with these holes and slide the soundbar onto the bracket, or screw it in depending on your model. Check your soundbar's manual for the exact attachment method—some slide on, some bolt down, and some use a quick-release clip.
Once the soundbar is attached, gently push up and down on it to make sure it does not move. If it shifts or feels loose, remove it and tighten the bracket screws on the wall. Do not hang the soundbar and then discover it is wobbly—fix it before you plug it in and walk away.
Connect the cables and test
Route the power cable and any audio cables (HDMI, optical, or aux) down the wall toward your TV or receiver. Many people use cable clips or a cable raceway to keep wires organized and hidden. Leave a little slack in the cables so the soundbar can vibrate without pulling the connections loose.
Plug in the soundbar, turn it on, and play some music or a movie scene with bass. Listen for any rattling or buzzing that might mean the bracket is loose or the soundbar is touching the wall. If everything sounds clean and the soundbar does not move when you touch it, you are done.
Frequently Asked Questions
Can I hang a soundbar without studs?
Yes, if you use heavy-duty drywall anchors rated for at least 25 pounds. Drill the holes, insert the anchors, and screw the bracket in. Studs are stronger and preferred, but anchors work for soundbars under 15 pounds. Check your soundbar's weight in the manual before choosing anchors.
What if my TV is mounted and there is no room below it?
Mount the soundbar above the TV instead, angled downward slightly so the sound projects toward the seating area. This is not ideal for sound quality, but it works. Some people also mount soundbars on a shelf or stand in front of the TV if wall space is not available.
Do I need to use the bracket that came with the soundbar?
Yes, unless you buy a universal bracket designed for your soundbar's size and weight. The bracket that comes in the box is engineered for that specific model. Using the wrong bracket risks the soundbar falling.
How do I hide the cables after hanging?
Use adhesive cable clips to route wires down the wall, or buy a cable raceway (a plastic channel that mounts to the wall and hides wires inside). Paint the raceway to match your wall, or run cables behind the TV stand if the soundbar is close enough. Avoid running cables across the floor where people can trip.
What if the soundbar is too heavy for drywall anchors?
Find studs and screw directly into them. If no studs are in the right spot, you may need to move the soundbar left or right to align with a stud, or consider a shelf or stand instead of wall mounting. Never hang a heavy soundbar on anchors alone.