Wall mounting a soundbar takes 30 to 45 minutes and requires only a stud finder, drill, and the bracket that came with your soundbar
Most soundbars mount to the wall using a bracket that attaches to wall studs with screws. The bracket then holds the soundbar itself. You will need a stud finder (a magnetic one costs $10 to $20 and works reliably), a drill with a Phillips bit, and the mounting bracket that came in your soundbar's box. If your soundbar did not include a bracket, you can buy a universal soundbar bracket for $15 to $40 at any electronics retailer.
The most common mistake is mounting the soundbar too high. It should sit at or slightly below ear level when you are seated on your couch—typically 24 to 36 inches above the floor, depending on your seating height. Mounting it above the TV is tempting but makes dialogue harder to hear clearly.
Key Takeaways
- Soundbars mount to wall studs, not drywall alone, so you must locate studs before drilling.
- Mount the soundbar at ear level when seated, not above the TV, to hear dialogue clearly.
- Use the bracket that came with your soundbar or a universal bracket rated for your soundbar's weight.
- Drill pilot holes first to prevent the screw from splitting the stud or the bracket from cracking.
- Run cables behind the wall or along the baseboard before mounting to avoid visible cords.
Locating studs and marking your drill points
Use a stud finder to locate the wooden studs behind your drywall. Turn the stud finder on and place it flat against the wall. Slide it slowly across the wall until it beeps or lights up—that marks the edge of a stud. Mark that spot with a pencil, then slide the finder in the opposite direction until it beeps again. The space between those two marks is the width of the stud (usually 1.5 inches). Mark the center of the stud with a pencil line.
Most soundbar brackets require two mounting holes, spaced 16 to 24 inches apart. Find two studs that are that distance apart, or use one stud and a toggle bolt (a special fastener that spreads behind the drywall) for the second hole if studs are not conveniently spaced. Mark the height where you want the bracket—remember, ear level when seated is the target. Use a level to make sure your pencil marks are horizontal, not tilted.
Drilling pilot holes and attaching the bracket
Drill a pilot hole at each marked point. A pilot hole is a small hole (usually 1/8 inch) drilled before the final screw goes in. It prevents the screw from splitting the stud and makes driving the screw easier. Use a drill bit slightly smaller than the diameter of the screws that came with your bracket.
Insert the bracket against the wall and align the bracket holes with your pilot holes. Drive the screws through the bracket into the studs using a drill or screwdriver. Tighten them firmly but do not over-tighten, which can crack the bracket or strip the screw. The bracket should not move or wiggle when you push on it.
Securing the soundbar to the bracket
Most soundbars slide onto the bracket from one side or sit on top of it and lock down with a single screw or clip. Check your soundbar's manual for the exact method. Slide or place the soundbar onto the bracket carefully—soundbars are heavy (usually 3 to 8 pounds) and can fall if not seated properly.
Tighten any locking screws or clips that hold the soundbar to the bracket. Give the soundbar a gentle upward push to confirm it is find and will not slip. Do not hang from the soundbar to test it; a gentle push is enough.
Running cables and hiding cords
Before you mount the soundbar, plan where the power cord and any audio cables will run. The cleanest look is to run cables behind the wall using a in-wall cable raceway (a plastic channel that mounts to the wall and hides cords inside). These cost $10 to $20 and are available at hardware stores. Alternatively, run cables down the back of the wall and along the baseboard, where they are less visible.
If your soundbar connects to your TV with an HDMI or optical cable, run that cable before mounting the soundbar. If it connects wirelessly via Bluetooth or WiFi, you only need to plug in the power cord. Plug the power cord into an outlet near the soundbar or into a power strip mounted behind the TV.
Adjusting soundbar angle and testing audio
Some soundbars tilt slightly up or down after mounting. Check your manual to see if your model allows angle adjustment. A slight upward tilt (5 to 10 degrees) can help direct sound toward ear level, especially if the soundbar is mounted higher than ideal.
Turn on your soundbar and TV and play a movie or show with clear dialogue. Listen from your normal seating position. If dialogue sounds muffled or hard to hear, the soundbar may be too high or too low. If it is too high, you will need to remount it lower. If it is too low, remount it higher. Most people get the height right on the first try if they measure ear level before drilling.
Common mounting mistakes to avoid
Mounting into drywall without studs is the most common error. Drywall anchors (plastic plugs that spread behind the drywall) can hold light objects, but a soundbar is too heavy. Always drill into studs. If studs are not positioned where you want the soundbar, use one stud and one toggle bolt, or move the soundbar location to align with studs.
Mounting the soundbar above the TV looks neat but degrades sound quality. Sound travels downward and forward, so a soundbar above the TV bounces sound off the ceiling instead of directing it toward your ears. Mount it below the TV or on the same wall as the TV at ear level.
Forgetting to run cables before mounting wastes time. Plan cable routes before you drill. If you realize after mounting that cables are visible and bother you, you can add a cable raceway afterward, but it is easier to hide them first.
Frequently Asked Questions
Can I mount a soundbar on a plaster or concrete wall?
Yes, but the process is different. Plaster walls require a stud finder designed for plaster, and concrete requires a masonry drill bit and concrete anchors. Both are available at hardware stores. The mounting steps are the same—find the right fasteners for your wall type, drill pilot holes, and find the bracket.
What if I rent and cannot drill holes?
Use a soundbar stand instead of wall mounting. Stands sit on a shelf or the floor in front of your TV and require no drilling. They cost $20 to $60 and work well if you have the floor or shelf space. Some renters also use heavy-duty adhesive strips designed for soundbars, though these are less stable than studs or stands.
How much weight can a soundbar bracket hold?
A bracket bolted to two studs can safely hold 20 to 50 pounds, depending on the bracket design. Most soundbars weigh 3 to 8 pounds, so a proper bracket installation is very safe. Check your bracket's weight rating on the packaging or manual to be sure.
Do I need to turn off the power before mounting?
You do not need to turn off the soundbar while you mount the bracket, but unplug the soundbar before you mount it to the bracket itself. This prevents accidental damage to the electronics if you slip with the drill or drop a screw inside the unit.
Can I mount a soundbar in a corner or on a side wall?
Yes, but it will not sound as good as mounting it on the wall your TV is on, centered below or at the same level as the TV. Corner mounting or side-wall mounting makes dialogue sound off-center and unnatural. If you must use a corner or side wall, angle the soundbar toward your seating area as much as possible.