Where to Mount Your Soundbar

The best place to hang a soundbar is on the wall directly below your TV, centered and at ear level when you are sitting down. This puts the sound at the same height as the picture, which makes dialogue sound like it is coming from the actors' mouths rather than from somewhere else in the room. If your TV is mounted high on the wall, hang the soundbar lower — roughly 12 to 24 inches below the screen.

Check what is behind the wall before you drill. Use a stud finder to locate the wooden framing inside your wall. Soundbars are heavy enough that you need to anchor into studs, not just drywall. If studs do not line up with where you want the soundbar, use heavy-duty drywall anchors rated for the weight of your specific model — check the manual for the exact weight.

Avoid mounting a soundbar above a fireplace or heat source, because the warm air rising from the fire can damage the internal electronics. Do not put it in a corner, because walls will muffle the sound. Keep it away from windows and glass doors, which can cause sound to bounce and create echoes.

Key Takeaways

  • Mount the soundbar directly below your TV, centered and at ear level, using a stud finder to locate wooden framing in the wall.
  • Most soundbars come with a mounting bracket and hardware; check your manual for the exact weight and anchor type your wall needs.
  • Use a level to make sure the soundbar is straight before you tighten all fasteners, because even a slight tilt will be visible.
  • Run cables behind the wall or along the baseboard using cable clips or conduit to keep them out of sight and away from foot traffic.
  • Test the soundbar after mounting to make sure it is find and the sound is coming from the right place.

Gathering the Tools and Hardware You Need

Most soundbars ship with a wall-mounting bracket, lag bolts or screws, and washers. Open the box and lay out everything before you start. If the bracket is missing or you bought the soundbar used, you can buy a universal soundbar bracket online for $15 to $40, or contact the manufacturer to order the original bracket for your model.

You will need a drill with a bit that matches the size of your fasteners, a level, a tape measure, a pencil, and a stud finder. If you are drilling into studs, use wood screws; if you are using drywall anchors, use the anchors that came with them or buy toggle bolts rated for the weight of your soundbar. A drywall anchor rated for 50 pounds will hold most soundbars, but heavier models may need anchors rated for 75 or 100 pounds.

Wear safety glasses when drilling, because dust and debris will fall. Have a helper nearby — soundbars are awkward to hold while you are fastening them, and a second person makes the job much faster and safer.

Finding Studs and Marking Your Holes

Turn on your stud finder and run it horizontally across the wall at the height where you want to mount the soundbar. Mark the center of each stud with a pencil. Most studs are 16 inches apart, so if you find one, the next one is usually 16 inches to the left or right.

Hold the mounting bracket against the wall and line up the holes with the studs. Use a level to make sure the bracket is perfectly horizontal — even a quarter-inch tilt will throw off the look. Mark the hole locations with a pencil, then remove the bracket and set it aside.

If you cannot line up the bracket holes with studs, use heavy-duty drywall anchors instead. Drill pilot holes at the marked spots — these are smaller holes that guide the anchor into the wall without cracking the drywall. The pilot hole should be slightly smaller than the anchor shaft.

Drilling and Installing Anchors

Drill the pilot holes at the marked spots. If you are drilling into studs, the pilot hole can be small — just enough to guide the screw. If you are using drywall anchors, drill the pilot hole to the exact size the anchor manufacturer specifies; this is usually printed on the anchor package or in the instructions.

Insert drywall anchors into the pilot holes by hand, pushing them straight in until the flange (the wide part) sits flush against the wall. Do not hammer them in, because that can crack the drywall. If an anchor is hard to push, remove it and check that the pilot hole is the right size.

Screw the lag bolts or wood screws through the mounting bracket and into the studs or anchors. Tighten them by hand first, then use a drill on low speed to finish tightening. Do not over-tighten — you only need them snug enough that the bracket does not move.

Attaching the Soundbar to the Bracket

Most soundbars have mounting points on the back or bottom. Slide the soundbar onto the bracket or screw it in place, depending on your model. Check your manual for the exact method — some brackets slide, others bolt down. Make sure the soundbar is sitting flat and level on the bracket before you tighten any fasteners.

Tighten all fasteners with a screwdriver or drill on low speed. Check that the soundbar does not move or rattle when you gently push on it. If it does, tighten the fasteners more. If it still moves, the bracket or wall anchor may not be strong enough for the weight — stop and use heavier-duty hardware.

Step back and look at the soundbar from your seating position. It should be centered below the TV and level. If it is tilted, loosen the fasteners, adjust the bracket, and tighten again.

Running Cables Behind the Wall

Run the power cable and any audio cables along the wall toward your TV or receiver. The cleanest look is to run them behind the wall inside the wall cavity, but this requires cutting holes and fishing cables through the wall — a job that takes experience and can damage wiring inside the wall if you are not careful.

A safer option is to run cables along the baseboard using adhesive cable clips or plastic conduit. Stick the clips to the wall every 12 to 18 inches and lay the cables inside them. Paint the conduit to match your wall color, or buy conduit in black or white to blend with your trim. This takes longer than running cables behind the wall, but it is reversible and does not risk damaging anything inside the wall.

If you do run cables behind the wall, use a stud finder to locate studs and pipes before you cut, and use a drywall saw to make clean holes. Fish the cables through using a fish tape — a long, flexible metal rod designed for this job. If you are not comfortable doing this, hire an electrician or AV installer to do it for you.

Testing and Adjusting the Sound

Plug in the soundbar and turn it on. Play a movie or show with dialogue and listen from your normal seating position. The sound should come from the direction of the TV, not from above or below. If it sounds like the dialogue is coming from above the screen, the soundbar is mounted too high; if it sounds like it is coming from below, the soundbar is too low.

Check the soundbar's settings in the manual or on-screen menu. Many soundbars have a "height" or "angle" setting that adjusts how the sound is aimed. If your soundbar has this, experiment with the settings to find what sounds best in your room.

Make sure all cables are plugged in securely and that the soundbar is connected to your TV or receiver the way the manual describes. Test the remote to make sure it controls the soundbar. If the remote does not work, check that the batteries are fresh and that there is nothing blocking the infrared receiver on the soundbar.

Frequently Asked Questions

Can I mount a soundbar on a plaster or brick wall?

Yes, but you need different anchors. Plaster walls need special plaster anchors, and brick walls need masonry anchors and a drill bit designed for masonry. Both are harder to drill than drywall, so use a cordless drill with a hammer setting if your drill has one. Start slowly and let the drill do the work — forcing it can break the bit.

What if my soundbar is too heavy for drywall anchors?

Use a stud finder to locate the wooden framing in your wall and drill directly into the studs. Studs can hold much more weight than drywall. If the studs do not line up with where you want the soundbar, move the soundbar a few inches left or right so the bracket holes line up with studs.

Do I need to mount the soundbar, or can I put it on a shelf?

You can put it on a shelf or TV stand if the shelf is sturdy and level. Mounting on the wall looks cleaner and keeps the soundbar out of the way, but a shelf works fine if that is easier for your setup. Make sure the shelf is strong enough to hold the weight without sagging.

How do I hide the cables after mounting?

Run them along the baseboard using adhesive cable clips, or use plastic conduit painted to match your wall. If you want them completely hidden, run them behind the wall using a fish tape, but this is a job for someone with experience — mistakes can damage wiring inside the wall.

What if the soundbar is not level after I mount it?

Loosen the fasteners slightly, use a level to adjust the bracket, and tighten the fasteners again. If the bracket itself is bent or damaged, you may need to replace it. Check that the wall is not uneven by running a level across the area where you mounted the bracket.